Re: [PATCH RFT 2/3] media: i2c: dw9719: Add DW9800W support

Hi Danila,

Thank you for the patch.

On Sat, Aug 01, 2026 at 09:04:15PM +0300, Danila Tikhonov wrote:
> The DW9800W uses the same chip ID and register layout as the DW9800K,
> but requires different default VCM frequency value.

Is this a real difference between the two models or what fits for the
attached lens? Too bad the datasheet isn't publicly available. :-(

At least the differing default and constraints for dongwoon,vcm-prescale
needs to be documented in bindings.

> 
> Add a separate device match entry for the DW9800W and validate the
> common chip ID. Use the matched variant to select the appropriate
> default values.
> 
> Tested on the Nothing Phone (1) smartphone.
> 
> Signed-off-by: Danila Tikhonov <[email protected]>
> ---
>  drivers/media/i2c/dw9719.c | 25 +++++++++++++++++++++----
>  1 file changed, 21 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/media/i2c/dw9719.c b/drivers/media/i2c/dw9719.c
> index 3b7ba88fd67c..bb9319fc350b 100644
> --- a/drivers/media/i2c/dw9719.c
> +++ b/drivers/media/i2c/dw9719.c
> @@ -44,6 +44,7 @@
>  
>  #define DW9719_INFO			CCI_REG8(0)
>  #define DW9719_ID			0xF1
> +#define DW9800_ID			0xF2
>  #define DW9761_ID			0xF4
>  
>  #define DW9719_CONTROL			CCI_REG8(2)
> @@ -72,6 +73,8 @@
>  #define DW9800K_MODE_SAC_SHIFT		6
>  #define DW9800K_DEFAULT_VCM_FREQ		0x10
>  
> +#define DW9800W_DEFAULT_VCM_FREQ	0x60
> +
>  #define to_dw9719_device(x) container_of(x, struct dw9719_device, sd)
>  
>  enum dw9719_model {
> @@ -79,6 +82,7 @@ enum dw9719_model {
>  	DW9719,
>  	DW9761,
>  	DW9800K,
> +	DW9800W,
>  };
>  
>  struct dw9719_device {
> @@ -140,10 +144,6 @@ static int dw9719_power_up(struct dw9719_device *dw9719, bool detect)
>  			dw9719->sac_mode = DW9718S_DEFAULT_SAC;
>  			dw9719->vcm_freq = DW9718S_DEFAULT_VCM_FREQ;
>  			goto props;
> -		case DW9800K:
> -			dw9719->sac_mode = DW9800K_DEFAULT_SAC;
> -			dw9719->vcm_freq = DW9800K_DEFAULT_VCM_FREQ;
> -			goto props;
>  		default:
>  			break;
>  		}
> @@ -159,6 +159,21 @@ static int dw9719_power_up(struct dw9719_device *dw9719, bool detect)
>  			dw9719->sac_mode = DW9719_DEFAULT_SAC;
>  			dw9719->vcm_freq = DW9719_DEFAULT_VCM_FREQ;
>  			break;
> +		case DW9800_ID:

Ideally the detection change would be in its own patch but I guess it's ok
as-is.

> +			dw9719->sac_mode = DW9800K_DEFAULT_SAC;
> +			switch (dw9719->model) {
> +			case DW9800K:
> +				dw9719->model = DW9800K;
> +				dw9719->vcm_freq = DW9800K_DEFAULT_VCM_FREQ;
> +				break;
> +			case DW9800W:
> +				dw9719->model = DW9800W;
> +				dw9719->vcm_freq = DW9800W_DEFAULT_VCM_FREQ;
> +				break;
> +			default:
> +				return -ENODEV;
> +			}
> +			break;
>  		case DW9761_ID:
>  			dw9719->model = DW9761;
>  			dw9719->mode_low_bits = 0x01;
> @@ -189,6 +204,7 @@ static int dw9719_power_up(struct dw9719_device *dw9719, bool detect)
>  
>  	switch (dw9719->model) {
>  	case DW9800K:
> +	case DW9800W:
>  		cci_write(dw9719->regmap, DW9719_CONTROL, DW9719_ENABLE_RINGING, &ret);
>  		cci_write(dw9719->regmap, DW9719_MODE,
>  			  dw9719->sac_mode << DW9800K_MODE_SAC_SHIFT, &ret);
> @@ -453,6 +469,7 @@ static const struct of_device_id dw9719_of_table[] = {
>  	{ .compatible = "dongwoon,dw9719", .data = (const void *)DW9719 },
>  	{ .compatible = "dongwoon,dw9761", .data = (const void *)DW9761 },
>  	{ .compatible = "dongwoon,dw9800k", .data = (const void *)DW9800K },
> +	{ .compatible = "dongwoon,dw9800w", .data = (const void *)DW9800W },
>  	{ }
>  };
>  MODULE_DEVICE_TABLE(of, dw9719_of_table);
> 

-- 
Kind regards,

Sakari Ailus