Re: [PATCH v5 13/25] clk: mediatek: pll: Add ops for PLLs using set/clr regs

Hi Louis-Alexis,

On Sat, Aug 01, 2026 at 01:20:59PM +0200, Louis-Alexis Eyraud wrote:
> MT8189 SoC uses a new combination of status and set/clr registers to
> control its PLL enable state and perform BAR reset, that are different
> than the current default clock prepare/unprepare operations are using.
> 
> Add new set of PLL clock operations to support this logic that relies
> on the following registers for prepare/unprepare operations:
>   - en/en_set/en_clr, rather than en register, for PLL enable
>     control
>   - rst_bar/rst_bar_set/rst_bar_clr, rather than default rst_bar
>     register for BAR reset control
> 
> Also, handle rst_bar register setting/clearing with a timeout, to
> verify the operation was correctly performed.
> 
> Signed-off-by: Louis-Alexis Eyraud <[email protected]>
> ---
>  drivers/clk/mediatek/clk-pll.c | 66 ++++++++++++++++++++++++++++++++++++++++++
>  drivers/clk/mediatek/clk-pll.h |  5 ++++
>  2 files changed, 71 insertions(+)
> 
> diff --git a/drivers/clk/mediatek/clk-pll.c b/drivers/clk/mediatek/clk-pll.c
> index 9a197a657dce..3118f68aa9ac 100644
> --- a/drivers/clk/mediatek/clk-pll.c
> +++ b/drivers/clk/mediatek/clk-pll.c
> @@ -9,6 +9,7 @@
>  #include <linux/delay.h>
>  #include <linux/err.h>
>  #include <linux/io.h>
> +#include <linux/iopoll.h>
>  #include <linux/module.h>
>  #include <linux/of_address.h>
>  #include <linux/platform_device.h>
> @@ -32,6 +33,7 @@
>  #define INTEGER_BITS		7
>  
>  #define PLL_STABILIZATION_DELAY	20 /* in us */
> +#define RST_BAR_TIMEOUT		20 /* in us */
>  
>  int mtk_pll_is_prepared(struct clk_hw *hw)
>  {
> @@ -301,6 +303,60 @@ void mtk_pll_unprepare(struct clk_hw *hw)
>  	mtk_pll_power_off(pll);
>  }
>  
> +int mtk_pll_prepare_setclr(struct clk_hw *hw)
> +{
> +	struct mtk_clk_pll *pll = to_mtk_clk_pll(hw);
> +	u32 val = 0;
> +	int ret;
> +
> +	mtk_pll_power_on(pll);
> +
> +	writel(BIT(pll->data->pll_en_bit), pll->en_set_addr);
> +
> +	__mtk_pll_tuner_enable(pll);
> +
> +	udelay(PLL_STABILIZATION_DELAY);
> +
> +	if (pll->data->flags & HAVE_RST_BAR) {
> +		writel(pll->data->rst_bar_mask, pll->rst_bar_set_addr);
> +
> +		ret = readl_poll_timeout(pll->rst_bar_addr, val,
> +					(val & pll->data->rst_bar_mask), 1,
> +					RST_BAR_TIMEOUT);
> +		if (ret) {
> +			mtk_pll_unprepare_setclr(hw);
> +			return ret;
> +		}
> +	}
> +
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(mtk_pll_prepare_setclr);
> +
> +void mtk_pll_unprepare_setclr(struct clk_hw *hw)
> +{
> +	struct mtk_clk_pll *pll = to_mtk_clk_pll(hw);
> +	u32 val = 0;
> +
> +	if (pll->data->flags & HAVE_RST_BAR) {
> +		writel(pll->data->rst_bar_mask, pll->rst_bar_clr_addr);
> +
> +		/* ignore return code to continue unpreparing the PLL if
> +		 * a error occurs on register read poll.

Use proper kernel comment:

  /*
   * Ignore return code...
   */

Also s/a error/an error/

With that fixed:

Reviewed-by: Brian Masney <[email protected]>