[PATCH v4 8/8] riscv: dts: starfive: jhb100: Add syscon nodes

Add syscon nodes for JHB100 RISC-V BMC SoC. They contain
pcieep0_ecsr_syscon | host0_syscon | husb0_syscon | husbd0_syscon |
pcieep1_ecsr_syscon | host1_syscon | husb1_syscon | husbd1_syscon |
gpu0_syscon | gpu1_syscon | husbcmn_syscon | b2h_syscon | h2b_syscon |
vout_syscon | pcierp_ecsr_syscon | pcierp_syscon | usb_syscon |
npu_syscon | per0_syscon | per1_syscon | per2_syscon | per3_syscon |
sys0_syscon | sys1_syscon | sys2_syscon | strap_syscon |
sfc0_filter_syscon | sfc1_filter_syscon | sfc2_filter_syscon.

Also update the references of pll nodes.

Signed-off-by: Changhuang Liang <[email protected]>
---
 arch/riscv/boot/dts/starfive/jhb100.dtsi | 193 +++++++++++++++++++----
 1 file changed, 159 insertions(+), 34 deletions(-)

diff --git a/arch/riscv/boot/dts/starfive/jhb100.dtsi b/arch/riscv/boot/dts/starfive/jhb100.dtsi
index 6b2863fd3fd3..e76cf0f3c380 100644
--- a/arch/riscv/boot/dts/starfive/jhb100.dtsi
+++ b/arch/riscv/boot/dts/starfive/jhb100.dtsi
@@ -282,36 +282,6 @@ pll1: clock-pll1 {
 		clock-frequency = <1000000000>;
 	};

-	pll2: clock-pll2 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <903168000>;
-	};
-
-	pll4: clock-pll4 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <100700000>;
-	};
-
-	pll5: clock-pll5 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <100700000>;
-	};
-
-	pll6: clock-pll6 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <2400000000>;
-	};
-
-	pll7: clock-pll7 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <1950000000>;
-	};
-
 	per2_gmac2_rgmii_rx: clock-per2-gmac2-rgmii-rx {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -393,6 +363,97 @@ bus_nioc: bus {
 				     <0x4 0x00000000 0x4 0x00000000 0x2 0x0>;
 			ranges;

+			pcieep0_ecsr_syscon: syscon@10511000 {
+				compatible = "starfive,jhb100-pcieep-ecsr-syscon", "syscon";
+				reg = <0x0 0x10511000 0x0 0x1000>;
+			};
+
+			host0_syscon: syscon@10519000 {
+				compatible = "starfive,jhb100-host-syscon", "syscon";
+				reg = <0x0 0x10519000 0x0 0x1000>;
+			};
+
+			husb0_syscon: syscon@10695000 {
+				compatible = "starfive,jhb100-husb-syscon", "syscon";
+				reg = <0x0 0x10695000 0x0 0x800>;
+			};
+
+			husbd0_syscon: syscon@10695800 {
+				compatible = "starfive,jhb100-husbd-syscon", "syscon";
+				reg = <0x0 0x10695800 0x0 0x800>;
+			};
+
+			gpu0_syscon: syscon@10745000 {
+				compatible = "starfive,jhb100-gpu-syscon", "syscon";
+				reg = <0x0 0x10745000 0x0 0x1000>;
+			};
+
+			pcieep1_ecsr_syscon: syscon@10d11000 {
+				compatible = "starfive,jhb100-pcieep-ecsr-syscon", "syscon";
+				reg = <0x0 0x10d11000 0x0 0x1000>;
+			};
+
+			host1_syscon: syscon@10d19000 {
+				compatible = "starfive,jhb100-host-syscon", "syscon";
+				reg = <0x0 0x10d19000 0x0 0x1000>;
+			};
+
+			husb1_syscon: syscon@10e95000 {
+				compatible = "starfive,jhb100-husb-syscon", "syscon";
+				reg = <0x0 0x10e95000 0x0 0x800>;
+			};
+
+			husbd1_syscon: syscon@10e95800 {
+				compatible = "starfive,jhb100-husbd-syscon", "syscon";
+				reg = <0x0 0x10e95800 0x0 0x800>;
+			};
+
+			gpu1_syscon: syscon@10f45000 {
+				compatible = "starfive,jhb100-gpu-syscon", "syscon";
+				reg = <0x0 0x10f45000 0x0 0x1000>;
+			};
+
+			husbcmn_syscon: syscon@11045000 {
+				compatible = "starfive,jhb100-husbcmn-syscon", "syscon";
+				reg = <0x0 0x11045000 0x0 0x1000>;
+			};
+
+			b2h_syscon: syscon@11135000 {
+				compatible = "starfive,jhb100-b2h-syscon", "syscon";
+				reg = <0x0 0x11135000 0x0 0x400>;
+			};
+
+			h2b_syscon: syscon@11135400 {
+				compatible = "starfive,jhb100-h2b-syscon", "syscon";
+				reg = <0x0 0x11135400 0x0 0x200>;
+			};
+
+			vout_syscon: syscon@11135800 {
+				compatible = "starfive,jhb100-vout-syscon", "syscon";
+				reg = <0x0 0x11135800 0x0 0x400>;
+			};
+
+			pcierp_ecsr_syscon: syscon@11711000 {
+				compatible = "starfive,jhb100-pcierp-ecsr-syscon", "syscon";
+				reg = <0x0 0x11711000 0x0 0x1000>;
+			};
+
+			pcierp_syscon: syscon@11719000 {
+				compatible = "starfive,jhb100-pcierp-syscon", "syscon";
+				reg = <0x0 0x11719000 0x0 0x1000>;
+				#reset-cells = <1>;
+			};
+
+			usb_syscon: syscon@11820000 {
+				compatible = "starfive,jhb100-usb-syscon", "syscon";
+				reg = <0x0 0x11820000 0x0 0x10000>;
+			};
+
+			npu_syscon: syscon@118e5000 {
+				compatible = "starfive,jhb100-npu-syscon", "syscon";
+				reg = <0x0 0x118e5000 0x0 0x100>;
+			};
+
 			uart6: serial@11982000 {
 				compatible = "starfive,jhb100-uart", "snps,dw-apb-uart";
 				reg = <0x0 0x11982000 0x0 0x400>;
@@ -410,7 +471,8 @@ uart6: serial@11982000 {
 			per0crg: clock-controller@11a08000 {
 				compatible = "starfive,jhb100-per0crg";
 				reg = <0x0 0x11a08000 0x0 0x1000>;
-				clocks = <&osc>, <&pll6>,
+				clocks = <&osc>,
+					 <&per0_syscon JHB100_PER0PLL_PLL6_OUT>,
 					 <&sys0crg JHB100_SYS0CLK_BMCPER0_CFG_400>,
 					 <&sys0crg JHB100_SYS0CLK_BMCPER0_CFG_800>,
 					 <&sys0crg JHB100_SYS0CLK_BMCPER0_NCNOC_INIT>,
@@ -422,10 +484,17 @@ per0crg: clock-controller@11a08000 {
 				#reset-cells = <1>;
 			};

+			per0_syscon: syscon@11a09000 {
+				compatible = "starfive,jhb100-per0-syscon", "syscon";
+				reg = <0x0 0x11a09000 0x0 0x1000>;
+				clocks = <&osc>;
+				#clock-cells = <1>;
+			};
+
 			per1crg: clock-controller@11b40000 {
 				compatible = "starfive,jhb100-per1crg";
 				reg = <0x0 0x11b40000 0x0 0x1000>;
-				clocks = <&pll7>,
+				clocks = <&per1_syscon JHB100_PER1PLL_PLL7_OUT>,
 					 <&sys0crg JHB100_SYS0CLK_BMCPER1_NCNOC_INIT>,
 					 <&sys0crg JHB100_SYS0CLK_BMCPER1_CFG_800>,
 					 <&sys2crg JHB100_SYS2CLK_BMCPER1_NCNOC_TARG>,
@@ -437,6 +506,13 @@ per1crg: clock-controller@11b40000 {
 				#reset-cells = <1>;
 			};

+			per1_syscon: syscon@11b41000 {
+				compatible = "starfive,jhb100-per1-syscon", "syscon";
+				reg = <0x0 0x11b41000 0x0 0x1000>;
+				clocks = <&osc>;
+				#clock-cells = <1>;
+			};
+
 			per2crg: clock-controller@11bc0000 {
 				compatible = "starfive,jhb100-per2crg";
 				reg = <0x0 0x11bc0000 0x0 0x1000>;
@@ -458,6 +534,11 @@ per2crg: clock-controller@11bc0000 {
 				#reset-cells = <1>;
 			};

+			per2_syscon: syscon@11bc1000 {
+				compatible = "starfive,jhb100-per2-syscon", "syscon";
+				reg = <0x0 0x11bc1000 0x0 0x1000>;
+			};
+
 			per3crg: clock-controller@11c40000 {
 				compatible = "starfive,jhb100-per3crg";
 				reg = <0x0 0x11c40000 0x0 0x1000>;
@@ -477,11 +558,16 @@ per3crg: clock-controller@11c40000 {
 				#reset-cells = <1>;
 			};

+			per3_syscon: syscon@11c41000 {
+				compatible = "starfive,jhb100-per3-syscon", "syscon";
+				reg = <0x0 0x11c41000 0x0 0x1000>;
+			};
+
 			sys0crg: clock-controller@13000000 {
 				compatible = "starfive,jhb100-sys0crg";
 				reg = <0x0 0x13000000 0x0 0x4000>;
 				clocks = <&osc>, <&pll0>, <&pll1>,
-					 <&pll2>;
+					 <&sys0_syscon JHB100_SYS0PLL_PLL2_OUT>;
 				clock-names = "osc", "pll0", "pll1", "pll2";
 				#clock-cells = <1>;
 				#reset-cells = <1>;
@@ -491,7 +577,9 @@ sys1crg: clock-controller@13004000 {
 				compatible = "starfive,jhb100-sys1crg";
 				reg = <0x0 0x13004000 0x0 0x4000>;
 				clocks = <&osc>, <&pll0>, <&pll1>,
-					 <&pll2>, <&pll4>, <&pll5>,
+					 <&sys0_syscon JHB100_SYS0PLL_PLL2_OUT>,
+					 <&sys0_syscon JHB100_SYS0PLL_PLL4_OUT>,
+					 <&sys0_syscon JHB100_SYS0PLL_PLL5_OUT>,
 					 <&sys0crg JHB100_SYS0CLK_NPU_NCNOC_INIT>;
 				clock-names = "osc", "pll0", "pll1", "pll2",
 					      "pll4", "pll5", "npu_ncnoc_init";
@@ -511,6 +599,28 @@ sys2crg: clock-controller@13008000 {
 				#reset-cells = <1>;
 			};

+			sys0_syscon: syscon@13010000 {
+				compatible = "starfive,jhb100-sys0-syscon", "syscon";
+				reg = <0x0 0x13010000 0x0 0x2000>;
+				clocks = <&osc>;
+				#clock-cells = <1>;
+			};
+
+			sys1_syscon: syscon@13014000 {
+				compatible = "starfive,jhb100-sys1-syscon", "syscon";
+				reg = <0x0 0x13014000 0x0 0x4000>;
+			};
+
+			sys2_syscon: syscon@13018000 {
+				compatible = "starfive,jhb100-sys2-syscon", "syscon";
+				reg = <0x0 0x13018000 0x0 0x2000>;
+			};
+
+			strap_syscon: syscon@1301a000 {
+				compatible = "starfive,jhb100-strap-syscon", "syscon";
+				reg = <0x0 0x1301a000 0x0 0x2000>;
+			};
+
 			intc: interrupt-controller@13220000 {
 				compatible = "starfive,jhb100-intc";
 				reg = <0x0 0x13220000 0x0 0x80>;
@@ -518,6 +628,21 @@ intc: interrupt-controller@13220000 {
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
+
+			sfc0_filter_syscon: syscon@14090000 {
+				compatible = "starfive,jhb100-sfc-filter-syscon", "syscon";
+				reg = <0x0 0x14090000 0x0 0x1000>;
+			};
+
+			sfc1_filter_syscon: syscon@14091000 {
+				compatible = "starfive,jhb100-sfc-filter-syscon", "syscon";
+				reg = <0x0 0x14091000 0x0 0x1000>;
+			};
+
+			sfc2_filter_syscon: syscon@14092000 {
+				compatible = "starfive,jhb100-sfc-filter-syscon", "syscon";
+				reg = <0x0 0x14092000 0x0 0x1000>;
+			};
 		};
 	};
 };
--
2.25.1