[PATCH 14/16] arm64: dts: st: enable usb on stm32mp257f-ev1

STM32MP257F-EV1 board uses two USB controllers:
- USB Host port, with external onboard HUB providing to connectors
- USB Dual role Type-C port
Both are capable of to operate in High-Speed mode.
The Type-C port management is done through integrated UCPD controller
and external TCPP03 I2C protection chip on I2C1.

Signed-off-by: Christian Bruel <[email protected]>
Signed-off-by: Fabrice Gasnier <[email protected]>
---
 arch/arm64/boot/dts/st/stm32mp257f-ev1.dts | 79 ++++++++++++++++++++++++++++++
 1 file changed, 79 insertions(+)

diff --git a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
index 14e033f365e3..6c2bfbf77aac 100644
--- a/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
+++ b/arch/arm64/boot/dts/st/stm32mp257f-ev1.dts
@@ -253,6 +253,28 @@ phy0_eth2: ethernet-phy@1 {
 	};
 };
 
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	tcpp: typec@34 {
+		compatible = "st,tcpp03";
+		reg = <0x34>;
+		enable-gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpiog>;
+		interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tcpp_flgn_pins_a>;
+		status = "okay";
+	};
+};
+
 &i2c2 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c2_pins_a>;
@@ -516,6 +538,27 @@ timer@11 {
 	};
 };
 
+&ucpd {
+	st,tcpp = <&tcpp>;
+	status = "okay";
+
+	connector {
+		compatible = "usb-c-connector";
+		label = "USB-C";
+		data-role = "dual";
+		power-role = "dual";
+		try-power-role = "sink";
+		typec-power-opmode = "1.5A";
+		pd-disable;
+		self-powered;
+		port {
+			typec_ep: endpoint {
+				remote-endpoint = <&dwc3_ep>;
+			};
+		};
+	};
+};
+
 &usart2 {
 	pinctrl-names = "default", "idle", "sleep";
 	pinctrl-0 = <&usart2_pins_a>;
@@ -534,3 +577,39 @@ &usart6 {
 	uart-has-rtscts;
 	status = "disabled";
 };
+
+&usb2_phy1 {
+	vdd33-supply = <&scmi_vdd3v3_usb>;
+	status = "okay";
+};
+
+&usb2_phy2 {
+	vdd33-supply = <&scmi_vdd3v3_usb>;
+	status = "okay";
+};
+
+&usb3dr {
+	maximum-speed = "high-speed";
+	phys = <&usb2_phy2>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+	port {
+		dwc3_ep: endpoint {
+			remote-endpoint = <&typec_ep>;
+		};
+	};
+};
+
+&usbh_ehci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&scmi_v3v3>;
+		vdda-supply = <&scmi_v3v3>;
+	};
+};

-- 
2.43.0