[PATCH v3 1/9] dt-bindings: iio: adc: support the TI ADS126x ADC family

The ADS1262 and ADS1263 are 32-bit, 38.4-kSPS delta-sigma ADCs with an
integrated PGA, internal reference, excitation and burn-out current
sources for sensor biasing and diagnostics. The ADS1263 adds a second,
24-bit delta-sigma ADC (ADC2) for background measurements.

Each can configure its own voltage reference source, the two excitation
current sources (IDAC), plus input and excitation channels rotation for
offset and IDAC mismatch cancellation. This lets the device drive and
ratiometrically measure RTDs and other resistive sensors.

Signed-off-by: Kurt Borja <[email protected]>
---
 .../devicetree/bindings/iio/adc/ti,ads1262.yaml    | 379 +++++++++++++++++++++
 MAINTAINERS                                        |   6 +
 2 files changed, 385 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/adc/ti,ads1262.yaml b/Documentation/devicetree/bindings/iio/adc/ti,ads1262.yaml
new file mode 100644
index 000000000000..c43ba7abb391
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti,ads1262.yaml
@@ -0,0 +1,379 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/ti,ads1262.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI ADS1262/ADS1263 analog to digital converter
+
+maintainers:
+  - Kurt Borja <[email protected]>
+
+description: |
+  The ADS1262 and ADS1263 are 38.4-kSPS, delta-sigma (ΔΣ) ADCs with an
+  integrated PGA, reference, and internal fault monitors. The ADS1263 integrates
+  an auxiliary, 24-bit, ΔΣ ADC intended for background measurements.
+
+  Datasheets:
+    - ADS126x: https://www.ti.com/lit/ds/symlink/ads1262.pdf
+
+properties:
+  compatible:
+    oneOf:
+      - const: ti,ads1262
+      - items:
+          - const: ti,ads1263
+          - const: ti,ads1262
+
+  reg:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  spi-max-frequency:
+    maximum: 8000000
+
+  spi-cpha: true
+
+  interrupts:
+    description: Data Ready (DRDY) interrupt line.
+    maxItems: 1
+
+  interrupt-names:
+    description:
+      Specify which pin should be configured as Data Ready interrupt.
+    enum: [drdy, dout-drdy]
+
+  start-gpios:
+    description: Start conversion control.
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  dvdd-supply:
+    description: Digital power supply.
+
+  avdd-supply:
+    description:
+      Analog power supply. In bipolar supply configurations, the reported
+      voltage should be in reference to DGND.
+
+  avss-supply:
+    description:
+      Negative analog power supply for bipolar configurations. AVSS can only be
+      at or below the ground reference (DGND). If not described, AVSS is assumed
+      to be connected to ground (0V).
+
+  clocks:
+    maxItems: 1
+
+  '#io-channel-cells':
+    minimum: 1
+    maximum: 2
+    description:
+      The first cell selects the channel by it's reg. The second cell selects
+      between ADC1 (0) and ADC2 (1).
+
+  '#gpio-cells':
+    const: 2
+
+  gpio-controller: true
+
+  regulators:
+    type: object
+    description:
+      List of regulators provided by this chip.
+
+    properties:
+      vbias:
+        $ref: /schemas/regulator/regulator.yaml#
+        type: object
+        description:
+          Level-shift voltage output on the AINCOM pin. Its output is the
+          mid-voltage of the analog supply, (AVDD + AVSS) / 2, and is used to
+          shift floating sensors to within the ADC input range.
+        unevaluatedProperties: false
+
+      refout:
+        $ref: /schemas/regulator/regulator.yaml#
+        type: object
+        description:
+          Buffered internal voltage reference output on the REFOUT pin.
+        unevaluatedProperties: false
+
+    additionalProperties: false
+
+patternProperties:
+  "^ain([0-9]|com)-supply$":
+    description:
+      Common-mode voltage supply connected to AIN<N> or AINCOM.
+
+  "^refp[1-3]-supply$":
+    description:
+      Positive voltage reference connected to REFP1 (AIN0), REFP2 (AIN2) or
+      REFP3 (AIN4). If not described, its assumed to be connected to ground
+      (0V).
+
+  "^refn[1-3]-supply$":
+    description:
+      Negative voltage reference connected to REFN1 (AIN1), REFN2 (AIN3) or
+      REFN3 (AIN5). If not described, its assumed to be connected to ground
+      (0V).
+
+  "^ti,refp[1-3]-refn[1-3]-resistor-ohms$":
+    description:
+      Magnitude of the external reference resistor connected between REFP<N>
+      and REFN<M>. In ratiometric configurations, such as RTD measurements, the
+      IDAC excitation current returns through this resistor, generating the
+      reference voltage for the conversion.
+
+  "^channel@[0-9]+$":
+    $ref: /schemas/iio/adc/adc.yaml#
+    unevaluatedProperties: false
+
+    properties:
+      reg:
+        maxItems: 1
+
+      single-channel:
+        minimum: 0
+        maximum: 10
+
+      common-mode-channel:
+        minimum: 0
+        maximum: 10
+        default: 10
+
+      diff-channels:
+        description: |
+          In addition to the analog input pins 0 (AIN0) - 10 (AINCOM), there are
+          special inputs that can be selected from the following values:
+          11: Temperature sensor monitor
+          12: Analog power supply monitor
+          13: Digital power supply monitor
+          14: TDAC test signal
+        items:
+          minimum: 0
+          maximum: 14
+
+      reference-sources:
+        minItems: 2
+        description:
+          Indicates the reference sources for this channel. The first and second
+          items are the positive (REFP) and negative (REFN) sources of the main
+          ADC (ADC1). The third item is the reference source of the secondary
+          ADC (ADC2) and must always have a positive differential voltage.
+        items:
+          - enum: [internal, refp1, refp2, refp3, avdd]
+          - enum: [internal, refn1, refn2, refn3, avss]
+          - enum: [internal, refp1-refn1, refp2-refn2, refp3-refn3, avdd-avss]
+
+      ti,reference-reversal:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Indicates that the ADC1 (this has no effect on ADC2) reference voltage
+          for this channel has negative polarity and thus should be internally
+          reversed.
+
+      excitation-channels:
+        minItems: 1
+        maxItems: 2
+        description:
+          Selects the pins for the IDAC sources from 0 (AIN0) to 10 (AINCOM).
+          The first value corresponds to IDAC1 and the second to IDAC2.
+        items:
+          minimum: 0
+          maximum: 10
+
+      excitation-current-nanoamp:
+        minItems: 1
+        maxItems: 2
+        description:
+          The first value corresponds to IDAC1 and the second to IDAC2.
+        items:
+          enum: [50000, 100000, 250000, 500000, 750000, 1000000, 1500000,
+                 2000000, 2500000, 3000000]
+
+      burn-out-current-nanoamp:
+        description:
+          Selects current magnitude for the sensor bias current source.
+        enum: [500, 2000, 10000, 50000, 200000]
+
+      ti,burn-out-resistor:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Instead of a fixed current, the sensor bias (burn-out) current source
+          can be pulled using an internal 10 MΩ resistor.
+
+      ti,burn-out-polarity:
+        $ref: /schemas/types.yaml#/definitions/string
+        description:
+          The sensor bias can be configured to either pull-up or pull-down mode.
+          In pull-up mode, the current flows into the positive input and flows
+          out of the negative input. In pull-down mode, the polarities are
+          reversed.
+        enum: [pull-up, pull-down]
+        default: pull-up
+
+      input-chopping: true
+
+      ti,idac-rotation:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          Automatically swap the IDAC1 and IDAC2 connections of alternate
+          conversions. The ADC averages the alternate conversions to eliminate
+          IDAC mismatch.
+
+    dependencies:
+      excitation-channels: [excitation-current-nanoamp]
+      excitation-current-nanoamp: [excitation-channels]
+      burn-out-current-nanoamp:
+        not:
+          required:
+            - ti,burn-out-resistor
+
+    required:
+      - reg
+
+    allOf:
+      - if:
+          properties:
+            excitation-channels:
+              maxItems: 1
+          required:
+            - excitation-channels
+        then:
+          properties:
+            excitation-current-nanoamp:
+              maxItems: 1
+        else:
+          properties:
+            excitation-current-nanoamp:
+              minItems: 2
+
+    oneOf:
+      - required: [single-channel]
+      - required: [diff-channels]
+
+dependencies:
+  interrupts: [interrupt-names]
+  interrupts-extended: [interrupt-names]
+
+required:
+  - compatible
+  - reg
+  - spi-cpha
+  - avdd-supply
+  - dvdd-supply
+  - '#address-cells'
+  - '#size-cells'
+
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,ads1263
+    then:
+      properties:
+        '#io-channel-cells':
+          const: 2
+      patternProperties:
+        "^channel@[0-9]+$":
+          properties:
+            reference-sources:
+              minItems: 3
+              maxItems: 3
+              default: [internal, internal, internal]
+    else:
+      properties:
+        '#io-channel-cells':
+          const: 1
+      patternProperties:
+        "^channel@[0-9]+$":
+          properties:
+            reference-sources:
+              minItems: 2
+              maxItems: 2
+              default: [internal, internal]
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        adc@0 {
+            compatible = "ti,ads1262";
+            reg = <0>;
+            spi-max-frequency = <8000000>;
+            spi-cpha;
+            avdd-supply = <&avdd>;
+            dvdd-supply = <&dvdd>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            interrupts-extended = <&gpio 0 IRQ_TYPE_EDGE_FALLING>;
+            interrupt-names = "drdy";
+
+            /* Typical common mode voltage configuration */
+            aincom-supply = <&ads1262_vbias>;
+
+            regulators {
+                ads1262_vbias: vbias {
+                    regulator-name = "vbias";
+                };
+            };
+
+            channel@0 {
+                reg = <0>;
+                single-channel = <0>;
+                /* The VBIAS is enabled on pin 10 (AINCOM) */
+                common-mode-channel = <10>;
+            };
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        adc@0 {
+            compatible = "ti,ads1263", "ti,ads1262";
+            reg = <0>;
+            spi-max-frequency = <8000000>;
+            spi-cpha;
+            avdd-supply = <&avdd>;
+            dvdd-supply = <&dvdd>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            interrupts-extended = <&gpio 0 IRQ_TYPE_EDGE_FALLING>;
+            interrupt-names = "drdy";
+
+            ti,refp2-refn2-resistor-ohms = <3520>;
+
+            channel@0 {
+                reg = <0>;
+                diff-channels = <4 5>;
+                reference-sources = "refp2", "refn2", "refp2-refn2";
+                excitation-channels = <1 6>;
+                excitation-current-nanoamp = <500000 500000>;
+            };
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 04fa5322d9f7..e9248979b801 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -27001,6 +27001,12 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/adc/ti,ads1018.yaml
 F:	drivers/iio/adc/ti-ads1018.c
 
+TI ADS1262 ADC DRIVER
+M:	Kurt Borja <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	Documentation/devicetree/bindings/iio/adc/ti,ads1262.yaml
+
 TI ADS7924 ADC DRIVER
 M:	Hugo Villeneuve <[email protected]>
 L:	[email protected]

-- 
2.55.0