[PATCH v4 3/7] arm64: dts: qcom: Add Motorola One

Add a devicetree for the Motorola One smartphone, which is based
on the Jacala/MSM8953 SoC.

Supported functionality as of this initial submission:
* I2C peripherals (NFC)
* Power Button, Volume Keys
* Regulators (PM8953)
* Remoteprocs (ADSP, MPSS, WCNSS)
* USB

Device tree also contains supply maps to other subsystems like MDSS
but due to missing dependencies like panel those are disabled.

Signed-off-by: Adam Skladowski <[email protected]>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 arch/arm64/boot/dts/qcom/msm8953-motorola-deen.dts | 440 +++++++++++++++++++++
 2 files changed, 441 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..11e953657691 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -120,6 +120,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-sony-xperia-kanuti-tulip.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-wingtech-wt82918.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8939-wingtech-wt82918hd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-flipkart-rimob.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-deen.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-mido.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8953-motorola-deen.dts b/arch/arm64/boot/dts/qcom/msm8953-motorola-deen.dts
new file mode 100644
index 000000000000..4bc407e23580
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8953-motorola-deen.dts
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) 2026 Adam Skladowski <[email protected]>
+ */
+
+/dts-v1/;
+#include <dt-bindings/usb/pd.h>
+#include "msm8953.dtsi"
+#include "pm8953.dtsi"
+#include "pmi8950.dtsi"
+
+/delete-node/ &cont_splash_mem;
+/delete-node/ &qseecom_mem;
+
+/ {
+	model = "Motorola One";
+	compatible = "motorola,deen", "qcom,msm8953";
+	chassis-type = "handset";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_key_default>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	reserved-memory {
+		qseecom_mem: qseecom@84300000 {
+			reg = <0x0 0x84300000 0x0 0x2000000>;
+			no-map;
+		};
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* Fake VBUS 5V supply till we wire pmi8950 one */
+	fusb302_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&hsusb_phy {
+	vdd-supply = <&pm8953_l3>;
+	vdda-phy-dpdm-supply = <&pm8953_l13>;
+	vdda-pll-supply = <&pm8953_l7>;
+
+	status = "okay";
+};
+
+&i2c_1 {
+	status = "okay";
+
+	typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupts-extended = <&tlmm 9 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&fusb302_int_default>;
+		pinctrl-names = "default";
+
+		vbus-supply = <&fusb302_vbus>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			data-role = "dual";
+			op-sink-microwatt = <2000000>;
+			try-power-role = "sink";
+			typec-power-opmode = "default";
+			source-pdos = <PDO_FIXED(5000, 500,
+						 PDO_FIXED_DUAL_ROLE |
+						 PDO_FIXED_DATA_SWAP |
+						 PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000,
+					       PDO_FIXED_DUAL_ROLE |
+					       PDO_FIXED_DATA_SWAP |
+					       PDO_FIXED_USB_COMM)>;
+
+			port {
+				fusb302: endpoint {
+					remote-endpoint = <&usb_dwc3_hs>;
+				};
+			};
+		};
+	};
+};
+
+&i2c_2 {
+	status = "okay";
+};
+
+&i2c_3 {
+	status = "okay";
+};
+
+&i2c_5 {
+	status = "okay";
+
+	pn553: nfc@28 {
+		compatible = "nxp,pn553", "nxp,nxp-nci-i2c";
+		reg = <0x28>;
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&nfc_firm_default &nfc_irq_default &nfc_pwr_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&ibb {
+	qcom,discharge-resistor-kohms = <32>;
+};
+
+&lpass {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8953_s3>;
+	vddio-supply = <&pm8953_l6>;
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vcca-supply = <&pm8953_l3>;
+};
+
+&mpss {
+	pll-supply = <&pm8953_l7>;
+
+	status = "okay";
+};
+
+&pm8953_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&pmi8950_wled {
+	qcom,current-limit-microamp = <25000>;
+	qcom,num-strings = <2>;
+
+	qcom,cabc;
+	qcom,external-pfet;
+};
+
+&q6afedai {
+	dai@22 {
+		reg = <QUATERNARY_MI2S_RX>;
+		qcom,sd-lines = <0>;
+	};
+
+	dai@127 {
+		reg = <QUINARY_MI2S_RX>;
+		qcom,sd-lines = <1>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8953-regulators";
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_l1-supply = <&pm8953_s3>;
+		vdd_l2_l3-supply = <&pm8953_s3>;
+		vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
+		vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
+		vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
+		vdd_l23-supply = <&pm8953_s3>;
+
+		pm8953_s1: s1 {
+			regulator-min-microvolt = <863000>;
+			regulator-max-microvolt = <1152000>;
+		};
+
+		pm8953_s3: s3 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1224000>;
+		};
+
+		pm8953_s4: s4 {
+			regulator-min-microvolt = <1896000>;
+			regulator-max-microvolt = <2048000>;
+		};
+
+		pm8953_l1: l1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8953_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8953_l3: l3 {
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+			regulator-allow-set-load;
+		};
+
+		pm8953_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8953_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1900000>;
+		};
+
+		pm8953_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8953_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8953_l10: l10 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+			regulator-system-load = <200000>;
+		};
+
+		pm8953_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8953_l13: l13 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3125000>;
+		};
+
+		pm8953_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8953_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8953_l19: l19 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8953_l22: l22 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+
+		pm8953_l23: l23 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8953_l8>;
+	vqmmc-supply = <&pm8953_l5>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_off>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-names = "default", "sleep";
+
+	vmmc-supply = <&pm8953_l11>;
+	vqmmc-supply = <&pm8953_l12>;
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <96 4>; /* Fingerprint SPI */
+
+	disp_reset_n_active: disp-reset-n-active-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	disp_reset_n_sleep: disp-reset-n-sleep-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	fusb302_int_default: fusb302-int-default-state {
+		pins = "gpio9";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	mi2s_sec_act: mi2s-quat-active-state {
+		pins = "gpio135", "gpio136", "gpio137", "gpio138";
+		function = "sec_mi2s";
+		drive-strength = <8>;
+	};
+
+	mi2s_sec_sus: mi2s-quat-sleep-state {
+		pins = "gpio135", "gpio136", "gpio137", "gpio138";
+		function = "sec_mi2s";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_firm_default: nfc-firm-state {
+		pins = "gpio62";
+		function = "gpio";
+		bias-pull-down;
+		output-low;
+		drive-strength = <2>;
+	};
+
+	nfc_irq_default: nfc-irq-state {
+		pins = "gpio17";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	nfc_pwr_default: nfc-pwr-state {
+		pins = "gpio16";
+		function = "gpio";
+		bias-pull-down;
+		output-low;
+		drive-strength = <2>;
+	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	ts_reset_default: ts-reset-default-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_reset_sleep: ts-reset-sleep-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb_dwc3_hs {
+	remote-endpoint = <&fusb302>;
+};
+
+&wcnss {
+	vddpx-supply = <&pm8953_l5>;
+
+	status = "okay";
+};
+
+&wcnss_iris {
+	compatible = "qcom,wcn3660b";
+
+	vdddig-supply = <&pm8953_l5>;
+	vddpa-supply = <&pm8953_l9>;
+	vddrfa-supply = <&pm8953_l19>;
+	vddxo-supply = <&pm8953_l7>;
+};

-- 
2.55.0