[PATCH 2/2] i2c: qcom-geni: Add I2C frequency table for firmware-based SEs

On IPQ5424, RTL-based I2C can be supported by both minicore and firmware
based SEs. For firmware-based SEs, use different SCL settings as
recommended by the design team. Introduce a separate table for the same.

Identify whether the SE is minicore or firmware-based and select the
appropriate frequency table to achieve the desired bus frequencies.

Move geni_i2c_clk_map_idx() from geni_i2c_resources_init() to
geni_i2c_init() to ensure SE_HW_PARAM_2 is accessed only after the
required clocks have been enabled.

Signed-off-by: Kathiravan Thirumoorthy <[email protected]>
---
 drivers/i2c/busses/i2c-qcom-geni.c | 23 +++++++++++++++++------
 include/linux/soc/qcom/geni-se.h   |  1 +
 2 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 00013b41a6f5..2f3026602c0c 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -194,12 +194,21 @@ static const struct geni_i2c_clk_fld geni_i2c_clk_map_32mhz[] = {
 	{}
 };
 
+static const struct geni_i2c_clk_fld geni_i2c_clk_map_32mhz_fwcore[] = {
+	{ I2C_MAX_STANDARD_MODE_FREQ, 12, 9, 10, 25 },
+	{ I2C_MAX_FAST_MODE_FREQ, 4, 3, 9, 18 },
+	{ I2C_MAX_FAST_MODE_PLUS_FREQ, 1, 6, 15, 29 },
+	{}
+};
+
 static int geni_i2c_clk_map_idx(struct geni_i2c_dev *gi2c)
 {
 	const struct geni_i2c_clk_fld *itr;
+	bool is_minicore = FIELD_GET(GEN_USE_MINICORES,
+				     readl_relaxed(gi2c->se.base + SE_HW_PARAM_2));
 
 	if (clk_get_rate(gi2c->se.clk) == 32 * HZ_PER_MHZ)
-		itr = geni_i2c_clk_map_32mhz;
+		itr = is_minicore ? geni_i2c_clk_map_32mhz : geni_i2c_clk_map_32mhz_fwcore;
 	else
 		itr = geni_i2c_clk_map_19p2mhz;
 
@@ -1046,6 +1055,13 @@ static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 		return ret;
 	}
 
+	ret = geni_i2c_clk_map_idx(gi2c);
+	if (ret) {
+		return dev_err_probe(gi2c->se.dev, ret, "Invalid clk frequency %d Hz\n",
+				     gi2c->clk_freq_out);
+		goto err;
+	}
+
 	proto = geni_se_read_proto(&gi2c->se);
 	if (proto == GENI_SE_INVALID_PROTO) {
 		ret = geni_load_se_firmware(&gi2c->se, GENI_SE_I2C);
@@ -1109,11 +1125,6 @@ static int geni_i2c_resources_init(struct geni_se *se)
 	if (ret)
 		return ret;
 
-	ret = geni_i2c_clk_map_idx(gi2c);
-	if (ret)
-		return dev_err_probe(gi2c->se.dev, ret, "Invalid clk frequency %d Hz\n",
-				     gi2c->clk_freq_out);
-
 	return geni_icc_set_bw_ab(&gi2c->se, GENI_DEFAULT_BW, GENI_DEFAULT_BW,
 				  Bps_to_icc(gi2c->clk_freq_out));
 }
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 29a53bbc0dd4..7e8c0bb6d674 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -331,6 +331,7 @@ struct geni_se {
 #define RX_FIFO_DEPTH_SHFT		16
 
 /* SE_HW_PARAM_2 fields */
+#define GEN_USE_MINICORES		BIT(12)
 #define PROG_RAM_DEPTH_MSK		GENMASK(10, 0)
 
 #define HW_VER_MAJOR_MASK		GENMASK(31, 28)

-- 
2.34.1