[PATCH V21 7/9] iio: imu: inv_icm42607: Add Gyroscope to icm42607

Chris Morgan <[email protected]>
Newsgroups org.kernel.vger.linux-iio,org.infradead.lists.linux-rockchip,org.kernel.vger.linux-devicetree
Message-ID <[email protected]>
From: Chris Morgan <[email protected]>

Add gyroscope functions to the icm42607 driver.

Signed-off-by: Chris Morgan <[email protected]>
---
 drivers/iio/imu/inv_icm42607/Makefile         |   1 +
 drivers/iio/imu/inv_icm42607/inv_icm42607.h   |   4 +
 .../iio/imu/inv_icm42607/inv_icm42607_core.c  |   5 +
 .../iio/imu/inv_icm42607/inv_icm42607_gyro.c  | 305 ++++++++++++++++++
 4 files changed, 315 insertions(+)
 create mode 100644 drivers/iio/imu/inv_icm42607/inv_icm42607_gyro.c

diff --git a/drivers/iio/imu/inv_icm42607/Makefile b/drivers/iio/imu/inv_icm42607/Makefile
index 372c6d6bdcec..8e73385c8f4b 100644
--- a/drivers/iio/imu/inv_icm42607/Makefile
+++ b/drivers/iio/imu/inv_icm42607/Makefile
@@ -2,6 +2,7 @@
 
 obj-$(CONFIG_INV_ICM42607) += inv-icm42607.o
 inv-icm42607-y += inv_icm42607_core.o
+inv-icm42607-y += inv_icm42607_gyro.o
 inv-icm42607-y += inv_icm42607_accel.o
 
 obj-$(CONFIG_INV_ICM42607_I2C) += inv-icm42607-i2c.o
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607.h b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
index fd3e57ee4f14..4d51b0da1aa1 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607.h
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
@@ -138,6 +138,7 @@ struct inv_icm42607_hw {
  *  @lock:		lock for serializing multiple registers access.
  *  @map:		regmap pointer.
  *  @indio_accel:	accelerometer IIO device.
+ *  @indio_gyro:	gyroscope IIO device.
  *  @vddio_supply:	I/O voltage regulator for the chip.
  *  @vddio_en:		I/O voltage status for runtime PM.
  *  @conf:		chip sensors configurations.
@@ -148,6 +149,7 @@ struct inv_icm42607_state {
 	struct mutex lock;
 	struct regmap *map;
 	struct iio_dev *indio_accel;
+	struct iio_dev *indio_gyro;
 	struct regulator *vddio_supply;
 	bool vddio_en;
 	struct inv_icm42607_conf conf;
@@ -412,6 +414,8 @@ int inv_icm42607_core_probe(struct regmap *regmap,
 			    const struct inv_icm42607_hw *hw,
 			    inv_icm42607_bus_setup bus_setup);
 
+struct iio_dev *inv_icm42607_gyro_init(struct inv_icm42607_state *st);
+
 struct iio_dev *inv_icm42607_accel_init(struct inv_icm42607_state *st);
 
 #endif
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
index 68e84597241a..190e998f7b8e 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
@@ -635,6 +635,11 @@ int inv_icm42607_core_probe(struct regmap *regmap,
 	if (IS_ERR(st->indio_accel))
 		return PTR_ERR(st->indio_accel);
 
+	/* Initialize IIO device for Gyro */
+	st->indio_gyro = inv_icm42607_gyro_init(st);
+	if (IS_ERR(st->indio_gyro))
+		return PTR_ERR(st->indio_gyro);
+
 	return 0;
 }
 EXPORT_SYMBOL_NS_GPL(inv_icm42607_core_probe, "IIO_ICM42607");
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_gyro.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_gyro.c
new file mode 100644
index 000000000000..b68d4d6f5c3f
--- /dev/null
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_gyro.c
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2026 InvenSense, Inc.
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/cleanup.h>
+#include <linux/device/devres.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#include "inv_icm42607.h"
+
+#define INV_ICM42607_GYRO_CHAN(_modifier, _index, _ext_info)			\
+{										\
+	.type = IIO_ANGL_VEL,							\
+	.modified = 1,								\
+	.channel2 = _modifier,							\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),				\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),			\
+	.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE),		\
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),		\
+	.info_mask_shared_by_all_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),	\
+	.scan_index = _index,							\
+	.scan_type = {								\
+		.sign = 's',							\
+		.realbits = 16,							\
+		.storagebits = 16,						\
+		.endianness = IIO_BE,						\
+	},									\
+	.ext_info = _ext_info,							\
+}
+
+enum inv_icm42607_gyro_scan {
+	INV_ICM42607_GYRO_SCAN_X,
+	INV_ICM42607_GYRO_SCAN_Y,
+	INV_ICM42607_GYRO_SCAN_Z,
+};
+
+static const struct iio_chan_spec_ext_info inv_icm42607_gyro_ext_infos[] = {
+	IIO_MOUNT_MATRIX(IIO_SHARED_BY_ALL, inv_icm42607_get_mount_matrix),
+	{ }
+};
+
+static const struct iio_chan_spec inv_icm42607_gyro_channels[] = {
+	INV_ICM42607_GYRO_CHAN(IIO_MOD_X, INV_ICM42607_GYRO_SCAN_X,
+			       inv_icm42607_gyro_ext_infos),
+	INV_ICM42607_GYRO_CHAN(IIO_MOD_Y, INV_ICM42607_GYRO_SCAN_Y,
+			       inv_icm42607_gyro_ext_infos),
+	INV_ICM42607_GYRO_CHAN(IIO_MOD_Z, INV_ICM42607_GYRO_SCAN_Z,
+			       inv_icm42607_gyro_ext_infos),
+};
+
+static const int inv_icm42607_gyro_scale_nano[][2] = {
+	[INV_ICM42607_GYRO_FS_2000DPS] = { 0, 1065264 },
+	[INV_ICM42607_GYRO_FS_1000DPS] = { 0, 532632 },
+	[INV_ICM42607_GYRO_FS_500DPS] = { 0, 266316 },
+	[INV_ICM42607_GYRO_FS_250DPS] = { 0, 133158 },
+};
+
+static int inv_icm42607_gyro_read_scale(struct iio_dev *indio_dev,
+					int *val, int *val2)
+{
+	struct inv_icm42607_state *st = iio_device_get_drvdata(indio_dev);
+	unsigned int idx;
+
+	guard(mutex)(&st->lock);
+
+	idx = st->conf.gyro.fs;
+
+	*val = inv_icm42607_gyro_scale_nano[idx][0];
+	*val2 = inv_icm42607_gyro_scale_nano[idx][1];
+	return IIO_VAL_INT_PLUS_NANO;
+}
+
+static int inv_icm42607_gyro_write_scale(struct iio_dev *indio_dev,
+					 int val, int val2)
+{
+	struct inv_icm42607_state *st = iio_device_get_drvdata(indio_dev);
+	struct device *dev = regmap_get_device(st->map);
+	unsigned int idx;
+	struct inv_icm42607_sensor_conf conf = INV_ICM42607_SENSOR_CONF_INIT;
+	size_t scales_len = ARRAY_SIZE(inv_icm42607_gyro_scale_nano);
+	int ret;
+
+	for (idx = 0; idx < scales_len; idx++) {
+		if (val == inv_icm42607_gyro_scale_nano[idx][0] &&
+		    val2 == inv_icm42607_gyro_scale_nano[idx][1])
+			break;
+	}
+	if (idx == scales_len)
+		return -EINVAL;
+
+	conf.fs = idx;
+
+	PM_RUNTIME_ACQUIRE_AUTOSUSPEND(dev, pm);
+	ret = PM_RUNTIME_ACQUIRE_ERR(&pm);
+	if (ret)
+		return ret;
+
+	guard(mutex)(&st->lock);
+
+	return inv_icm42607_set_sensor_conf(st, &conf, IIO_ANGL_VEL);
+}
+
+/* IIO format int + micro , values 0-4 reserved. */
+static const int inv_icm42607_gyro_odr[][2] = {
+	[INV_ICM42607_ODR_1600HZ] = { 1600, 0 },
+	[INV_ICM42607_ODR_800HZ] = { 800, 0 },
+	[INV_ICM42607_ODR_400HZ] = { 400, 0 },
+	[INV_ICM42607_ODR_200HZ] = { 200, 0 },
+	[INV_ICM42607_ODR_100HZ] = { 100, 0 },
+	[INV_ICM42607_ODR_50HZ] = { 50, 0 },
+	[INV_ICM42607_ODR_25HZ] = { 25, 0 },
+	[INV_ICM42607_ODR_12_5HZ] = { 12, 500000 },
+};
+
+static int inv_icm42607_gyro_read_odr(struct inv_icm42607_state *st,
+				      int *val, int *val2)
+{
+	unsigned int odr;
+	unsigned int i;
+
+	guard(mutex)(&st->lock);
+
+	odr = st->conf.gyro.odr;
+
+	for (i = INV_ICM42607_ODR_1600HZ; i < ARRAY_SIZE(inv_icm42607_gyro_odr); i++) {
+		if (i == odr)
+			break;
+	}
+	if (i == ARRAY_SIZE(inv_icm42607_gyro_odr))
+		return -EINVAL;
+
+	*val = inv_icm42607_gyro_odr[i][0];
+	*val2 = inv_icm42607_gyro_odr[i][1];
+
+	return IIO_VAL_INT_PLUS_MICRO;
+}
+
+static int inv_icm42607_gyro_write_odr(struct iio_dev *indio_dev,
+				       int val, int val2)
+{
+	struct inv_icm42607_state *st = iio_device_get_drvdata(indio_dev);
+	struct device *dev = regmap_get_device(st->map);
+	unsigned int idx;
+	struct inv_icm42607_sensor_conf conf = INV_ICM42607_SENSOR_CONF_INIT;
+	int ret;
+
+	for (idx = INV_ICM42607_ODR_1600HZ;
+	     idx < ARRAY_SIZE(inv_icm42607_gyro_odr); idx++) {
+		if (val == inv_icm42607_gyro_odr[idx][0] &&
+		    val2 == inv_icm42607_gyro_odr[idx][1])
+			break;
+	}
+	if (idx == ARRAY_SIZE(inv_icm42607_gyro_odr))
+		return -EINVAL;
+
+	conf.odr = idx;
+
+	PM_RUNTIME_ACQUIRE_AUTOSUSPEND(dev, pm);
+	ret = PM_RUNTIME_ACQUIRE_ERR(&pm);
+	if (ret)
+		return ret;
+
+	guard(mutex)(&st->lock);
+
+	return inv_icm42607_set_sensor_conf(st, &conf, IIO_ANGL_VEL);
+}
+
+static int inv_icm42607_gyro_read_raw(struct iio_dev *indio_dev,
+				      struct iio_chan_spec const *chan,
+				      int *val, int *val2, long mask)
+{
+	struct inv_icm42607_state *st = iio_device_get_drvdata(indio_dev);
+	s16 data;
+	int ret;
+
+	switch (chan->type) {
+	case IIO_ANGL_VEL:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = inv_icm42607_read_sensor(indio_dev, chan, &data);
+		if (ret)
+			return ret;
+		*val = data;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		return inv_icm42607_gyro_read_scale(indio_dev, val, val2);
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return inv_icm42607_gyro_read_odr(st, val, val2);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int inv_icm42607_gyro_read_avail(struct iio_dev *indio_dev,
+					struct iio_chan_spec const *chan,
+					const int **vals,
+					int *type, int *length, long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		if (chan->type != IIO_ANGL_VEL)
+			return -EINVAL;
+		*vals = (const int *)inv_icm42607_gyro_scale_nano;
+		*type = IIO_VAL_INT_PLUS_NANO;
+		*length = ARRAY_SIZE(inv_icm42607_gyro_scale_nano) * 2;
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*vals = (const int *)inv_icm42607_gyro_odr[INV_ICM42607_ODR_1600HZ];
+		*type = IIO_VAL_INT_PLUS_MICRO;
+		*length = (ARRAY_SIZE(inv_icm42607_gyro_odr) -
+			   INV_ICM42607_ODR_1600HZ) * 2;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int inv_icm42607_gyro_write_raw(struct iio_dev *indio_dev,
+				       struct iio_chan_spec const *chan,
+				       int val, int val2, long mask)
+{
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		if (chan->type != IIO_ANGL_VEL)
+			return -EINVAL;
+		ret = inv_icm42607_gyro_write_scale(indio_dev, val, val2);
+		return ret;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return inv_icm42607_gyro_write_odr(indio_dev, val, val2);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int inv_icm42607_gyro_write_raw_get_fmt(struct iio_dev *indio_dev,
+					       struct iio_chan_spec const *chan,
+					       long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		if (chan->type != IIO_ANGL_VEL)
+			return -EINVAL;
+		return IIO_VAL_INT_PLUS_NANO;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return IIO_VAL_INT_PLUS_MICRO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static const struct iio_info inv_icm42607_gyro_info = {
+	.read_raw = inv_icm42607_gyro_read_raw,
+	.read_avail = inv_icm42607_gyro_read_avail,
+	.write_raw = inv_icm42607_gyro_write_raw,
+	.write_raw_get_fmt = inv_icm42607_gyro_write_raw_get_fmt,
+};
+
+struct iio_dev *inv_icm42607_gyro_init(struct inv_icm42607_state *st)
+{
+	struct device *dev = regmap_get_device(st->map);
+	const char *name;
+	struct inv_icm42607_sensor_state *gyro_st;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	name = devm_kasprintf(dev, GFP_KERNEL, "%s-gyro", st->hw->name);
+	if (!name)
+		return ERR_PTR(-ENOMEM);
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*gyro_st));
+	if (!indio_dev)
+		return ERR_PTR(-ENOMEM);
+
+	gyro_st = iio_priv(indio_dev);
+	gyro_st->power_mode = INV_ICM42607_SENSOR_MODE_LOW_NOISE;
+	gyro_st->filter = INV_ICM42607_FILTER_BW_73HZ;
+
+	indio_dev->name = name;
+	indio_dev->info = &inv_icm42607_gyro_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = inv_icm42607_gyro_channels;
+	indio_dev->num_channels = ARRAY_SIZE(inv_icm42607_gyro_channels);
+	iio_device_set_drvdata(indio_dev, st);
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return indio_dev;
+}
-- 
2.43.0
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.