Re: [PATCH v5 04/13] iio: gyro: hid-sensor-gyro-3d: convert probe and teardown to devm-managed resources

On Thu, 06 Aug 2026 17:55:50 +0530
Sanjay Chitroda via B4 Relay <[email protected]> wrote:

> From: Sanjay Chitroda <[email protected]>
> 
> Convert HID IIO driver resource management to use devm-managed helpers,
> tying the lifetime of all resources to the device.
> 
> HID trigger setup, IIO registration, and sensor hub callback resource
> are now managed using devm APIs. Cleanup logic previously handled
> explicitly in probe error and teardown paths.
> 
> This simplifies the probe path by removing goto-based error handling,
> eliminates the remove callback entirely.
> 
> Signed-off-by: Sanjay Chitroda <[email protected]>
> ---
>  drivers/iio/gyro/hid-sensor-gyro-3d.c | 41 ++++++++---------------------------

Nice stats - could be even better with some error printing cleanups though.
See below.  I appreciate you may not want to do that in this series, but
it's simple enough I wouldn't mind, even though lots of patches result.

>  1 file changed, 9 insertions(+), 32 deletions(-)
> 
> diff --git a/drivers/iio/gyro/hid-sensor-gyro-3d.c b/drivers/iio/gyro/hid-sensor-gyro-3d.c
> index cf049700d415..66778315e86d 100644
> --- a/drivers/iio/gyro/hid-sensor-gyro-3d.c
> +++ b/drivers/iio/gyro/hid-sensor-gyro-3d.c
> @@ -264,7 +264,8 @@ static int gyro_3d_parse_report(struct platform_device *pdev,
>  /* Function to initialize the processing for usage id */
>  static int hid_gyro_3d_probe(struct platform_device *pdev)
>  {
> -	struct hid_sensor_hub_device *hsdev = dev_get_platdata(&pdev->dev);
> +	struct device *dev = &pdev->dev;
> +	struct hid_sensor_hub_device *hsdev = dev_get_platdata(dev);
>  	int ret = 0;
>  	static const char *name = "gyro_3d";
>  	struct iio_dev *indio_dev;
> @@ -311,8 +312,8 @@ static int hid_gyro_3d_probe(struct platform_device *pdev)
>  
>  	atomic_set(&gyro_state->common_attributes.data_ready, 0);
>  
> -	ret = hid_sensor_setup_trigger(indio_dev, name,
> -				       &gyro_state->common_attributes);
> +	ret = devm_hid_sensor_setup_trigger(dev, indio_dev, name,
> +					    &gyro_state->common_attributes);
>  	if (ret < 0) {
>  		dev_err(&pdev->dev, "trigger setup failed\n");

>  		return ret;
> @@ -321,38 +322,15 @@ static int hid_gyro_3d_probe(struct platform_device *pdev)
>  	gyro_state->callbacks.send_event = gyro_3d_proc_event;
>  	gyro_state->callbacks.capture_sample = gyro_3d_capture_sample;
>  	gyro_state->callbacks.pdev = pdev;
> -	ret = sensor_hub_register_callback(hsdev, HID_USAGE_SENSOR_GYRO_3D,
> -					   &gyro_state->callbacks);
> +	ret = devm_sensor_hub_register_callback(dev, hsdev,
> +						HID_USAGE_SENSOR_GYRO_3D,
> +						&gyro_state->callbacks);
>  	if (ret < 0) {
>  		dev_err(&pdev->dev, "callback reg failed\n");
Obviously makes for a larger patch set but error print cleaning up would
be nice.  This patch makes that easier to do as enables
return dev_err_probe() in a few places where we didn't have direct returns before.

There are also some prints in here that should be dropped (memory
allocation failures etc).

Jonathan

> -		goto error_remove_trigger;
> -	}
> -	iio_device_unregister(indio_dev);
> -	sensor_hub_remove_callback(hsdev, HID_USAGE_SENSOR_GYRO_3D);
> -	hid_sensor_remove_trigger(&gyro_state->common_attributes);
> +	return devm_iio_device_register(dev, indio_dev);
>  }
>  
>  static const struct platform_device_id hid_gyro_3d_ids[] = {
> @@ -371,7 +349,6 @@ static struct platform_driver hid_gyro_3d_platform_driver = {
>  		.pm	= &hid_sensor_pm_ops,
>  	},
>  	.probe		= hid_gyro_3d_probe,
> -	.remove		= hid_gyro_3d_remove,
>  };
>  module_platform_driver(hid_gyro_3d_platform_driver);
>  
>