Re: [RFC PATCH v2 1/4] security: ima: call ima_init() again at late_initcall_sync for defered TPM

On Wed, 2026-04-22 at 20:41 +0100, Yeoreum Yun wrote:
> > Hi Mimi,
> > 
> > > On Wed, 2026-04-22 at 17:24 +0100, Yeoreum Yun wrote:
> > > > To generate the boot_aggregate log in the IMA subsystem with TPM PCR values,
> > > > the TPM driver must be built as built-in and
> > > > must be probed before the IMA subsystem is initialized.
> > > > 
> > > > However, when the TPM device operates over the FF-A protocol using
> > > > the CRB interface, probing fails and returns -EPROBE_DEFER if
> > > > the tpm_crb_ffa device — an FF-A device that provides the communication
> > > > interface to the tpm_crb driver — has not yet been probed.
> > > > 
> > > > To ensure the TPM device operating over the FF-A protocol with
> > > > the CRB interface is probed before IMA initialization,
> > > > the following conditions must be met:
> > > > 
> > > >    1. The corresponding ffa_device must be registered,
> > > >       which is done via ffa_init().
> > > > 
> > > >    2. The tpm_crb_driver must successfully probe this device via
> > > >       tpm_crb_ffa_init().
> > > > 
> > > >    3. The tpm_crb driver using CRB over FF-A can then
> > > >       be probed successfully. (See crb_acpi_add() and
> > > >       tpm_crb_ffa_init() for reference.)
> > > > 
> > > > Unfortunately, ffa_init(), tpm_crb_ffa_init(), and crb_acpi_driver_init() are
> > > > all registered with device_initcall, which means crb_acpi_driver_init() may
> > > > be invoked before ffa_init() and tpm_crb_ffa_init() are completed.
> > > > 
> > > > When this occurs, probing the TPM device is deferred.
> > > > However, the deferred probe can happen after the IMA subsystem
> > > > has already been initialized, since IMA initialization is performed
> > > > during late_initcall, and deferred_probe_initcall() is performed
> > > > at the same level.
> > > > 
> > > > To resolve this, call ima_init() again at late_inicall_sync level
> > > > so that let IMA not miss TPM PCR value when generating boot_aggregate
> > > > log though TPM device presents in the system.
> > > > 
> > > > Signed-off-by: Yeoreum Yun <[email protected]>
> > > 
> > > A lot of change for just detecting whether ima_init() is being called on
> > > late_initcall or late_initcall_sync(), without any explanation for all the other
> > > changes (e.g. ima_init_core).
> > > 
> > > Please just limit the change to just calling ima_init() twice.
> > 
> > My concern is that ima_update_policy_flags() will be called
> > when ima_init() is deferred -- not initialised anything.
> > though functionally, it might be okay however,
> > I think ima_update_policy_flags() and notifier should work after ima_init()
> > works logically.
> > 
> > This change I think not much quite a lot. just wrapper ima_init() with
> > ima_init_core() with some error handling.
> > 
> > Am I missing something?
> 
> Also, if we handle in ima_init() only, but it failed with other reason,
> we shouldn't call again ima_init() in the late_initcall_sync.
> 
> To handle this, It wouldn't do in the ima_init() but we need to handle
> it by caller of ima_init().

Only tpm_default_chip() is being called to set the ima_tpm_chip.  On failure,
instead of going into TPM-bypass mode, return immediately.  There are no calls
to anything else.  Just call ima_init() a second time.

Mimi