PROBLEM: uhci-hcd under 2.6* kernel hangs the system
MIkE <[email protected]> Mon, 26 Jan 2004 13:56:08 +0100
| Newsgroups | org.kernel.vger.linux-laptop |
|---|---|
| Message-ID | <[email protected]> |
when I "modprobe uhci-hcd" the systems hangs after about a minute! tried this under 2.6.0, 2.6.1-rc1 and 2.6.1 only my good old 2.4.19 works with usb-uhci Hardware: Samsung Q10 notebook 00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) 00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) 00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02) the other details as attachement ! anyone mentioned this before ?? mike -- a woman can fake an orgasm, but it takes a man to fake an entire relationship :-)
lspci.txt
(application/octet-stream, 7.8 KB)
00:00.0 Host bridge: Intel Corp. 82830 830 Chipset Host Bridge (rev 04) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at <unassigned> (32-bit, prefetchable) Capabilities: [40] #09 [0105] 00:02.0 VGA compatible controller: Intel Corp. 82830 CGC [Chipset Graphics Controller] (rev 04) (prog-if 00 [VGA]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.1 Display controller: Intel Corp. 82830 CGC [Chipset Graphics Controller] Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (2500ns max) Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at e0080000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 4: I/O ports at 8c80 [size=32] 00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at 8ca0 [size=32] 00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at 8cc0 [size=32] 00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=03, sec-latency=168 I/O behind bridge: 0000a000-0000afff Memory behind bridge: e0200000-e02fffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at 9000 [size=16] Region 5: Memory at 10000000 (32-bit, non-prefetchable) [size=1K] 00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus Controller (rev 02) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at 8ce0 [size=32] 00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio Controller (rev 02) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at 8400 [size=256] Region 1: I/O ports at 80c0 [size=64] 00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02) (prog-if 00 [Generic]) Subsystem: PCTel Inc: Unknown device 4c31 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at 8800 [size=256] Region 1: I/O ports at 8c00 [size=128] 02:03.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev b8) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 168 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 10400000-107ff000 (prefetchable) Memory window 1: 10800000-10bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001 02:03.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C551 IEEE 1394 Controller (prog-if 10 [OHCI]) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 64 (500ns min, 1000ns max) Interrupt: pin B routed to IRQ 11 Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=2K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME+ 02:05.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) Subsystem: Samsung Electronics Co Ltd: Unknown device c002 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 80 (2500ns min, 2500ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a000 [size=128] Region 1: Memory at e0200800 (32-bit, non-prefetchable) [size=128] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D3 PME-Enable+ DSel=0 DScale=2 PME-
dmesg.txt
(application/octet-stream, 8.7 KB)
Linux version 2.6.1 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #1 Sat Jan 17 10:23:02 CET 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e400 (usable) BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000c0000 - 00000000000d4000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable) BIOS-e820: 000000000f6e0000 - 000000000f6f0000 (ACPI data) BIOS-e820: 000000000f6f0000 - 000000000f700000 (ACPI NVS) BIOS-e820: 000000000f700000 - 000000000f780000 (usable) BIOS-e820: 000000000f780000 - 0000000010000000 (reserved) BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 247MB LOWMEM available. On node 0 totalpages: 63360 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 59264 pages, LIFO batch:14 HighMem zone: 0 pages, LIFO batch:1 DMI present. Building zonelist for node : 0 Kernel command line: root=/dev/hda5 vga=789 pci=usepirqmask quiet Initializing CPU#0 PID hash table entries: 1024 (order 10: 8192 bytes) Detected 531.823 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Memory: 247740k/253440k available (1455k kernel code, 4844k reserved, 581k data, 124k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 1048.57 BogoMIPS Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) III Mobile CPU 800MHz stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd9aa, last bus=3 PCI: Using configuration type 1 mtrr: v2.0 (20020519) PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) Transparent bridge - 0000:00:1e.0 PCI: Using IRQ router PIIX/ICH [8086/248c] at 0000:00:1f.0 PCI: Found IRQ 11 for device 0000:00:1f.1 PCI: Sharing IRQ 11 with 0000:00:1d.2 PCI: Sharing IRQ 11 with 0000:02:03.1 PCI: Found IRQ 10 for device 0000:02:03.0 PCI: Sharing IRQ 10 with 0000:00:02.0 PCI: Sharing IRQ 10 with 0000:00:1d.0 vesafb: framebuffer at 0xe8000000, mapped to 0xd0000000, size 8000k vesafb: mode is 800x600x32, linelength=3200, pages=3 vesafb: protected mode interface info at 00ff:44f0 vesafb: scrolling: redraw vesafb: directcolor: size=8:8:8:8, shift=24:16:8:0 fb0: VESA VGA frame buffer device SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) devfs: v1.22 (20021013) Richard Gooch ([email protected]) devfs: boot_options: 0x1 Console: switching to colour frame buffer device 100x37 pty: 256 Unix98 ptys configured Non-volatile memory driver v1.2 hw_random hardware driver 1.0.0 loaded Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A PCI: Found IRQ 10 for device 0000:00:1f.6 PCI: Sharing IRQ 10 with 0000:00:1f.3 PCI: Sharing IRQ 10 with 0000:00:1f.5 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH3M: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) PCI: Found IRQ 11 for device 0000:00:1f.1 PCI: Sharing IRQ 11 with 0000:00:1d.2 PCI: Sharing IRQ 11 with 0000:02:03.1 ICH3M: chipset revision 2 ICH3M: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio hda: IC25N020ATCS04-0, ATA DISK drive Using anticipatory io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 > Console: switching to colour frame buffer device 100x37 mice: PS/2 mouse device common for all mice i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) NET: Registered protocol family 17 PM: Reading pmdisk image. PM: Resume from disk failed. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 124k freed NET: Registered protocol family 1 Adding 512056k swap on /dev/hda2. Priority:-1 extents:1 EXT3 FS on hda5, internal journal SCSI subsystem initialized Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: Found IRQ 10 for device 0000:02:03.0 PCI: Sharing IRQ 10 with 0000:00:02.0 PCI: Sharing IRQ 10 with 0000:00:1d.0 Yenta: CardBus bridge found at 0000:02:03.0 [144d:c002] Yenta: ISA IRQ mask 0x02b8, PCI irq 10 Socket status: 30000006 orinoco.c 0.13e (David Gibson <[email protected]> and others) orinoco_cs.c 0.13e (David Gibson <[email protected]> and others) ohci1394: $Rev: 1087 $ Ben Collins <[email protected]> PCI: Found IRQ 11 for device 0000:02:03.1 PCI: Sharing IRQ 11 with 0000:00:1d.2 PCI: Sharing IRQ 11 with 0000:00:1f.1 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e0200000-e02007ff] Max Packet=[2048] Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 830M Chipset. agpgart: Maximum main memory to use for agp memory: 196M agpgart: Detected 8060K stolen memory. agpgart: AGP aperture is 128M @ 0xe8000000 mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x400000 [drm] Initialized i830 1.3.2 20021108 on minor 0 PCI: Found IRQ 11 for device 0000:02:05.0 PCI: Sharing IRQ 11 with 0000:00:1d.1 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:02:05.0: 3Com PCI 3c905C Tornado at 0xa000. Vers LK1.1.19 ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000f041040081b1] Synaptics Touchpad, model: 1 Firmware: 5.9 180 degree mounted touchpad Sensor: 37 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub PCI: Found IRQ 10 for device 0000:00:1f.5 PCI: Sharing IRQ 10 with 0000:00:1f.3 PCI: Sharing IRQ 10 with 0000:00:1f.6 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0: clocking to 48000 kjournald starting. Commit interval 5 seconds EXT3 FS on hda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd7fff 0xe0000-0xfffff eth1: Station identity 001f:0003:0000:0008 eth1: Looks like an Intersil firmware version 0.8.3 eth1: Ad-hoc demo mode supported eth1: IEEE standard IBSS ad-hoc mode supported eth1: WEP supported, 104-bit key eth1: MAC address 00:03:2F:00:B6:22 eth1: Station name "Prism I" eth1: ready eth1: index 0x01: Vcc 5.0, irq 10, io 0x0100-0x013f eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode. eth1: New link status: Disconnected (0002) eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode. eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode. eth1: New link status: Connected (0001) inserting floppy driver for 2.6.1 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 mtrr: base(0xe8000000) is not aligned on a size(0x300000) boundary PCI: Found IRQ 10 for device 0000:00:02.0 PCI: Sharing IRQ 10 with 0000:00:1d.0 PCI: Sharing IRQ 10 with 0000:02:03.0 mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x400000 atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). spurious 8259A interrupt: IRQ7.
ver_linux.txt
(application/octet-stream, 977 B)
If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux yoda 2.6.1 #1 Sat Jan 17 10:23:02 CET 2004 i686 Intel(R) Pentium(R) III Mobile CPU 800MHz GenuineIntel GNU/Linux Gnu C 3.2.3 Gnu make 3.80 util-linux 2.11z mount 2.11z module-init-tools 0.9.12 e2fsprogs 1.34 pcmcia-cs 3.2.5 PPP 2.4.1 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.1.12 Net-tools 1.60 Kbd 1.06 Sh-utils 5.0 Modules Loaded sg floppy snd_intel8x0 snd_ac97_codec snd_mpu401_uart snd_rawmidi snd_pcm_oss snd_pcm snd_page_alloc snd_timer snd_mixer_oss snd soundcore usbcore psmouse 3c59x i830 intel_agp agpgart ohci1394 ieee1394 orinoco_cs ds orinoco hermes yenta_socket pcmcia_core sr_mod scsi_mod cdrom unix
cpuinfo.txt
(application/octet-stream, 401 B)
processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 11 model name : Intel(R) Pentium(R) III Mobile CPU 800MHz stepping : 1 cpu MHz : 531.823 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse bogomips : 1048.57
modules.txt
(application/octet-stream, 1.4 KB)
sg 30476 0 - Live 0xd09fd000 floppy 56116 0 - Live 0xd0a11000 snd_intel8x0 29124 0 - Live 0xd09bf000 snd_ac97_codec 52868 1 snd_intel8x0, Live 0xd09ef000 snd_mpu401_uart 6400 1 snd_intel8x0, Live 0xd0977000 snd_rawmidi 20480 1 snd_mpu401_uart, Live 0xd09af000 snd_pcm_oss 49412 0 - Live 0xd09e1000 snd_pcm 87808 2 snd_intel8x0,snd_pcm_oss, Live 0xd09ca000 snd_page_alloc 9348 2 snd_intel8x0,snd_pcm, Live 0xd088d000 snd_timer 22016 1 snd_pcm, Live 0xd097b000 snd_mixer_oss 17408 1 snd_pcm_oss, Live 0xd08b7000 snd 43652 8 snd_intel8x0,snd_ac97_codec,snd_mpu401_uart,snd_rawmidi,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss, Live 0xd0982000 soundcore 7360 1 snd, Live 0xd0891000 usbcore 106964 1 - Live 0xd0993000 psmouse 18828 0 - Live 0xd0894000 3c59x 35752 0 - Live 0xd089a000 i830 71576 2 - Live 0xd08a4000 intel_agp 16280 1 - Live 0xd084a000 agpgart 27208 3 intel_agp, Live 0xd0885000 ohci1394 32512 0 - Live 0xd087c000 ieee1394 210572 1 ohci1394, Live 0xd08bd000 orinoco_cs 6920 1 - Live 0xd0840000 ds 11264 3 orinoco_cs, Live 0xd083c000 orinoco 42756 1 orinoco_cs, Live 0xd0870000 hermes 8064 2 orinoco_cs,orinoco, Live 0xd0839000 yenta_socket 14848 1 - Live 0xd0829000 pcmcia_core 56832 3 orinoco_cs,ds,yenta_socket, Live 0xd0861000 sr_mod 13472 0 - Live 0xd0824000 scsi_mod 65572 2 sg,sr_mod, Live 0xd084f000 cdrom 33440 1 sr_mod, Live 0xd082f000 unix 23948 420 - Live 0xd07dd000
ioports.txt
(application/octet-stream, 704 B)
0000-001f : dma1 0020-0021 : pic1 0040-005f : timer 0060-006f : keyboard 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 0100-013f : orinoco_cs 01f0-01f7 : ide0 03c0-03df : vesafb 03f6-03f6 : ide0 03f8-03ff : serial 0cf8-0cff : PCI conf1 4000-40ff : PCI CardBus #03 4400-44ff : PCI CardBus #03 80c0-80ff : 0000:00:1f.5 80c0-80ff : Intel 82801CA-ICH3 - Controller 8400-84ff : 0000:00:1f.5 8400-84ff : Intel 82801CA-ICH3 - AC'97 8800-88ff : 0000:00:1f.6 8c00-8c7f : 0000:00:1f.6 8c80-8c9f : 0000:00:1d.0 8ca0-8cbf : 0000:00:1d.1 8cc0-8cdf : 0000:00:1d.2 8ce0-8cff : 0000:00:1f.3 9000-900f : 0000:00:1f.1 9000-9007 : ide0 a000-a07f : 0000:02:05.0 a000-a07f : 0000:02:05.0
interrupts.txt
(application/octet-stream, 365 B)
CPU0 0: 2373908 XT-PIC timer 1: 11754 XT-PIC i8042 2: 0 XT-PIC cascade 10: 11028 XT-PIC yenta, Intel 82801CA-ICH3, orinoco_cs 11: 4 XT-PIC ohci1394 12: 174027 XT-PIC i8042 14: 9686 XT-PIC ide0 NMI: 0 ERR: 1
iomem.txt
(application/octet-stream, 983 B)
00000000-0009e3ff : System RAM 0009e400-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000d3fff : reserved 000d4000-000d47ff : Extension ROM 000d4800-000d4fff : Extension ROM 000f0000-000fffff : System ROM 00100000-0f6dffff : System RAM 00100000-0026be4d : Kernel code 0026be4e-002fd57f : Kernel data 0f6e0000-0f6effff : ACPI Tables 0f6f0000-0f6fffff : ACPI Non-volatile Storage 0f700000-0f77ffff : System RAM 0f780000-0fffffff : reserved 10000000-100003ff : 0000:00:1f.1 10001000-10001fff : 0000:02:03.0 10001000-10001fff : yenta_socket 10400000-107fffff : PCI CardBus #03 10800000-10bfffff : PCI CardBus #03 60000000-60000fff : card services e0000000-e007ffff : 0000:00:02.0 e0080000-e00fffff : 0000:00:02.1 e0200000-e02007ff : 0000:02:03.1 e0200000-e02007ff : ohci1394 e0200800-e020087f : 0000:02:05.0 e8000000-efffffff : 0000:00:02.0 e8000000-e87cffff : vesafb f0000000-f7ffffff : 0000:00:02.1 ff800000-ffbfffff : reserved fff00000-ffffffff : reserved
kernel-log-2.4.19.txt
(application/octet-stream, 2.1 KB)
Jan 17 11:32:59 localhost kernel: memory : cd6e8160 Jan 17 11:33:58 localhost kernel: usb-uhci.c: $Revision: 1.275 $ time 00:10:23 Nov 3 2003 Jan 17 11:33:58 localhost kernel: usb-uhci.c: High bandwidth mode enabled Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 10 for device 00:1d.0 Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 10 with 00:02.0 Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 10 with 02:03.0 Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.0 to 64 Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8c80, IRQ 10 Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 1 Jan 17 11:33:58 localhost kernel: hub.c: USB hub found Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 11 for device 00:1d.1 Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 02:05.0 Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.1 to 64 Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8ca0, IRQ 11 Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 2 Jan 17 11:33:58 localhost kernel: hub.c: USB hub found Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 11 for device 00:1d.2 Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 00:1f.1 Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 02:03.1 Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.2 to 64 Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8cc0, IRQ 11 Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 3 Jan 17 11:33:58 localhost kernel: hub.c: USB hub found Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected Jan 17 11:33:58 localhost kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
kernel-log-2.6.0.txt
(application/octet-stream, 6.2 KB)
Jan 17 11:22:31 [kernel] Linux version 2.6.0 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #4 Mon Dec 29 13:02:07 CET 2003 Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.0 to 64 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: irq 10, io base 00008c80 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: root hub device address 1 Jan 17 11:24:04 [kernel] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 11:24:04 [kernel] usb usb1: Product: UHCI Host Controller Jan 17 11:24:04 [kernel] usb usb1: Manufacturer: Linux 2.6.0 uhci_hcd Jan 17 11:24:04 [kernel] usb usb1: SerialNumber: 0000:00:1d.0 Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:04 [kernel] usb usb1: registering 1-0:1.0 (config #1, interface 0) Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:04 [kernel] hub 1-0:1.0: usb_probe_interface Jan 17 11:24:04 [kernel] hub 1-0:1.0: usb_probe_interface - got id Jan 17 11:24:04 [kernel] hub 1-0:1.0: USB hub found Jan 17 11:24:04 [kernel] hub 1-0:1.0: 2 ports detected Jan 17 11:24:04 [kernel] hub 1-0:1.0: standalone hub Jan 17 11:24:04 [kernel] hub 1-0:1.0: ganged power switching Jan 17 11:24:04 [kernel] hub 1-0:1.0: global over-current protection Jan 17 11:24:04 [kernel] hub 1-0:1.0: Port indicators are not supported Jan 17 11:24:04 [kernel] hub 1-0:1.0: power on to power good time: 2ms Jan 17 11:24:04 [kernel] hub 1-0:1.0: hub controller current requirement: 0mA Jan 17 11:24:04 [kernel] hub 1-0:1.0: local power source is good Jan 17 11:24:04 [kernel] hub 1-0:1.0: no over-current condition exists Jan 17 11:24:04 [kernel] hub 1-0:1.0: enabling power on all ports Jan 17 11:24:04 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.1 Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:02:05.0 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: UHCI Host Controller Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.1 to 64 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: irq 11, io base 00008ca0 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: root hub device address 1 Jan 17 11:24:04 [kernel] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 11:24:04 [kernel] usb usb2: Product: UHCI Host Controller Jan 17 11:24:04 [kernel] usb usb2: Manufacturer: Linux 2.6.0 uhci_hcd Jan 17 11:24:04 [kernel] usb usb2: SerialNumber: 0000:00:1d.1 Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:04 [kernel] usb usb2: registering 2-0:1.0 (config #1, interface 0) Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:04 [kernel] hub 2-0:1.0: usb_probe_interface Jan 17 11:24:04 [kernel] hub 2-0:1.0: usb_probe_interface - got id Jan 17 11:24:04 [kernel] hub 2-0:1.0: USB hub found Jan 17 11:24:04 [kernel] hub 2-0:1.0: 2 ports detected Jan 17 11:24:04 [kernel] hub 2-0:1.0: standalone hub Jan 17 11:24:04 [kernel] hub 2-0:1.0: ganged power switching Jan 17 11:24:04 [kernel] hub 2-0:1.0: global over-current protection Jan 17 11:24:04 [kernel] hub 2-0:1.0: Port indicators are not supported Jan 17 11:24:04 [kernel] hub 2-0:1.0: power on to power good time: 2ms Jan 17 11:24:04 [kernel] hub 2-0:1.0: hub controller current requirement: 0mA Jan 17 11:24:04 [kernel] hub 2-0:1.0: local power source is good Jan 17 11:24:04 [kernel] hub 2-0:1.0: no over-current condition exists Jan 17 11:24:04 [kernel] hub 2-0:1.0: enabling power on all ports Jan 17 11:24:04 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.2 Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:00:1f.1 Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:02:03.1 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: UHCI Host Controller Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.2 to 64 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: irq 11, io base 00008cc0 Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: root hub device address 1 Jan 17 11:24:04 [kernel] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 11:24:04 [kernel] usb usb3: Product: UHCI Host Controller Jan 17 11:24:04 [kernel] usb usb3: Manufacturer: Linux 2.6.0 uhci_hcd Jan 17 11:24:04 [kernel] usb usb3: SerialNumber: 0000:00:1d.2 Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:04 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0) Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 11:24:05 [kernel] hub 3-0:1.0: usb_probe_interface Jan 17 11:24:05 [kernel] hub 3-0:1.0: usb_probe_interface - got id Jan 17 11:24:05 [kernel] hub 3-0:1.0: USB hub found Jan 17 11:24:05 [kernel] hub 3-0:1.0: 2 ports detected Jan 17 11:24:05 [kernel] hub 3-0:1.0: standalone hub Jan 17 11:24:05 [kernel] hub 3-0:1.0: ganged power switching Jan 17 11:24:05 [kernel] hub 3-0:1.0: global over-current protection Jan 17 11:24:05 [kernel] hub 3-0:1.0: Port indicators are not supported Jan 17 11:24:05 [kernel] hub 3-0:1.0: power on to power good time: 2ms Jan 17 11:24:05 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA Jan 17 11:24:05 [kernel] hub 3-0:1.0: local power source is good Jan 17 11:24:05 [kernel] hub 3-0:1.0: no over-current condition exists Jan 17 11:24:05 [kernel] hub 3-0:1.0: enabling power on all ports Jan 17 11:24:06 [kernel] drivers/usb/host/uhci-hcd.c: 8c80: suspend_hc Jan 17 11:24:06 [kernel] drivers/usb/host/uhci-hcd.c: 8ca0: suspend_hc Jan 17 11:24:07 [kernel] drivers/usb/host/uhci-hcd.c: 8cc0: suspend_hc
kernel-log-2.6.1.txt
(application/octet-stream, 6.2 KB)
Jan 17 10:28:35 [kernel] Linux version 2.6.1 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #1 Sat Jan 17 10:23:02 CET 2004 Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 Jan 17 10:30:28 [kernel] PCI: Setting latency timer of device 0000:00:1d.0 to 64 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: irq 10, io base 00008c80 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: root hub device address 1 Jan 17 10:30:28 [kernel] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 10:30:28 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 10:30:28 [kernel] usb usb1: Product: UHCI Host Controller Jan 17 10:30:28 [kernel] usb usb1: Manufacturer: Linux 2.6.1 uhci_hcd Jan 17 10:30:28 [kernel] usb usb1: SerialNumber: 0000:00:1d.0 Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:28 [kernel] usb usb1: registering 1-0:1.0 (config #1, interface 0) Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:28 [kernel] hub 1-0:1.0: usb_probe_interface Jan 17 10:30:28 [kernel] hub 1-0:1.0: usb_probe_interface - got id Jan 17 10:30:28 [kernel] hub 1-0:1.0: USB hub found Jan 17 10:30:28 [kernel] hub 1-0:1.0: 2 ports detected Jan 17 10:30:28 [kernel] hub 1-0:1.0: standalone hub Jan 17 10:30:28 [kernel] hub 1-0:1.0: ganged power switching Jan 17 10:30:28 [kernel] hub 1-0:1.0: global over-current protection Jan 17 10:30:28 [kernel] hub 1-0:1.0: Port indicators are not supported Jan 17 10:30:28 [kernel] hub 1-0:1.0: power on to power good time: 2ms Jan 17 10:30:28 [kernel] hub 1-0:1.0: hub controller current requirement: 0mA Jan 17 10:30:28 [kernel] hub 1-0:1.0: local power source is good Jan 17 10:30:28 [kernel] hub 1-0:1.0: no over-current condition exists Jan 17 10:30:28 [kernel] hub 1-0:1.0: enabling power on all ports Jan 17 10:30:28 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.1 Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:02:05.0 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: UHCI Host Controller Jan 17 10:30:28 [kernel] PCI: Setting latency timer of device 0000:00:1d.1 to 64 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: irq 11, io base 00008ca0 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: root hub device address 1 Jan 17 10:30:28 [kernel] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 10:30:28 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 10:30:28 [kernel] usb usb2: Product: UHCI Host Controller Jan 17 10:30:28 [kernel] usb usb2: Manufacturer: Linux 2.6.1 uhci_hcd Jan 17 10:30:28 [kernel] usb usb2: SerialNumber: 0000:00:1d.1 Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:28 [kernel] usb usb2: registering 2-0:1.0 (config #1, interface 0) Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:28 [kernel] hub 2-0:1.0: usb_probe_interface Jan 17 10:30:28 [kernel] hub 2-0:1.0: usb_probe_interface - got id Jan 17 10:30:28 [kernel] hub 2-0:1.0: USB hub found Jan 17 10:30:28 [kernel] hub 2-0:1.0: 2 ports detected Jan 17 10:30:28 [kernel] hub 2-0:1.0: standalone hub Jan 17 10:30:28 [kernel] hub 2-0:1.0: ganged power switching Jan 17 10:30:28 [kernel] hub 2-0:1.0: global over-current protection Jan 17 10:30:28 [kernel] hub 2-0:1.0: Port indicators are not supported Jan 17 10:30:28 [kernel] hub 2-0:1.0: power on to power good time: 2ms Jan 17 10:30:28 [kernel] hub 2-0:1.0: hub controller current requirement: 0mA Jan 17 10:30:28 [kernel] hub 2-0:1.0: local power source is good Jan 17 10:30:28 [kernel] hub 2-0:1.0: no over-current condition exists Jan 17 10:30:28 [kernel] hub 2-0:1.0: enabling power on all ports Jan 17 10:30:28 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.2 Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:00:1f.1 Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:02:03.1 Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.2: UHCI Host Controller Jan 17 10:30:29 [kernel] PCI: Setting latency timer of device 0000:00:1d.2 to 64 Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: irq 11, io base 00008cc0 Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 Jan 17 10:30:29 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: root hub device address 1 Jan 17 10:30:29 [kernel] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 17 10:30:29 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 17 10:30:29 [kernel] usb usb3: Product: UHCI Host Controller Jan 17 10:30:29 [kernel] usb usb3: Manufacturer: Linux 2.6.1 uhci_hcd Jan 17 10:30:29 [kernel] usb usb3: SerialNumber: 0000:00:1d.2 Jan 17 10:30:29 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:29 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0) Jan 17 10:30:29 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 17 10:30:29 [kernel] hub 3-0:1.0: usb_probe_interface Jan 17 10:30:29 [kernel] hub 3-0:1.0: usb_probe_interface - got id Jan 17 10:30:29 [kernel] hub 3-0:1.0: USB hub found Jan 17 10:30:29 [kernel] hub 3-0:1.0: 2 ports detected Jan 17 10:30:29 [kernel] hub 3-0:1.0: standalone hub Jan 17 10:30:29 [kernel] hub 3-0:1.0: ganged power switching Jan 17 10:30:29 [kernel] hub 3-0:1.0: global over-current protection Jan 17 10:30:29 [kernel] hub 3-0:1.0: Port indicators are not supported Jan 17 10:30:29 [kernel] hub 3-0:1.0: power on to power good time: 2ms Jan 17 10:30:29 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA Jan 17 10:30:29 [kernel] hub 3-0:1.0: local power source is good Jan 17 10:30:29 [kernel] hub 3-0:1.0: no over-current condition exists Jan 17 10:30:29 [kernel] hub 3-0:1.0: enabling power on all ports Jan 17 10:30:30 [kernel] drivers/usb/host/uhci-hcd.c: 8c80: suspend_hc Jan 17 10:30:30 [kernel] drivers/usb/host/uhci-hcd.c: 8ca0: suspend_hc Jan 17 10:30:31 [kernel] drivers/usb/host/uhci-hcd.c: 8cc0: suspend_hc