[PATCH v6 3/3] arm64: dts: qcom: sm8250: Add JPEG encoder node

Add the JPEG encoder hardware node to the SM8250 device tree so the
qcom-jpeg V4L2 encoder driver can bind and operate on this platform.

Signed-off-by: Atanas Filipov <[email protected]>
---
 arch/arm64/boot/dts/qcom/sm8250.dtsi | 72 ++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index f11da2ca4181..d42b29419320 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
+#include <dt-bindings/interconnect/qcom,icc.h>
 #include <dt-bindings/interconnect/qcom,sm8250.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/phy/phy-qcom-qmp.h>
@@ -4486,6 +4487,77 @@ cci1_i2c1: i2c-bus@1 {
 			};
 		};
 
+		jpeg-encoder@ac53000 {
+			compatible = "qcom,sm8250-jpeg-enc";
+			status = "disabled";
+
+			reg = <0x0 0x0ac53000 0x0 0x1000>;
+
+			interrupts = <GIC_SPI 474 IRQ_TYPE_EDGE_RISING>;
+
+			power-domains = <&camcc TITAN_TOP_GDSC>,
+					<&rpmhpd RPMHPD_MMCX>,
+					<&rpmhpd RPMHPD_MX>;
+			power-domain-names = "titan_top", "mmcx", "mx";
+
+			clocks = <&gcc GCC_CAMERA_SF_AXI_CLK>,
+				 <&camcc CAM_CC_CORE_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_JPEG_CLK>;
+
+			clock-names = "sf_axi",
+				      "core_ahb",
+				      "cpas_ahb",
+				      "cnoc_axi",
+				      "jpeg";
+
+			interconnects = <&gem_noc MASTER_AMPSS_M0 QCOM_ICC_TAG_ACTIVE_ONLY
+					 &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>,
+					<&mmss_noc MASTER_CAMNOC_SF QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI_CH0 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "cpu-cfg",
+					     "sf-mnoc";
+
+			iommus = <&apps_smmu 0x2040 0x400>;
+
+			operating-points-v2 = <&jpeg_opp_table>;
+
+			jpeg_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <400000000>,
+						 /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <400000000>,
+						 /bits/ 64 <200000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-400000000 {
+					opp-hz = /bits/ 64 <400000000>,
+						 /bits/ 64 <400000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-480000000 {
+					opp-hz = /bits/ 64 <400000000>,
+						 /bits/ 64 <480000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+
+				opp-600000000 {
+					opp-hz = /bits/ 64 <400000000>,
+						 /bits/ 64 <600000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+		};
+
 		camss: camss@ac6a000 {
 			compatible = "qcom,sm8250-camss";
 			status = "disabled";
-- 
2.34.1