[PATCH v2 0/6] Add support for IPQ5018 Bluetooth

George Moussalem via B4 Relay <[email protected]>
Newsgroups org.kernel.vger.linux-mmc,org.infradead.lists.ath10k,org.kernel.feeds.b4-sent,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-block,org.kernel.vger.linux-bluetooth,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel,org.kernel.vger.linux-remoteproc,org.kernel.vger.linux-wireless,org.kernel.vger.netdev
Message-ID <[email protected]>
Hello,

This patch series introduces Bluetooth support for IPQ5018.

Bluetooth firmware is loaded by the host into a dedicated reserved
memory carveout and authenticated by TrustZone. A Secure Channel Manager
(SCM) call safely brings the peripheral core out of reset.

A shared memory ring buffer topology handles runtime data frame
transport between the host APSS and the Bluetooth controller.
An outgoing APCS IPC bit and an incoming GIC interrupt handle
host/guest signaling.

This series has been tested and verified on various IPQ5018 router
boards utilizing firmware extracted from GPL distributions, using both
mdt and mbn file formats.

[   14.781511] Bluetooth: hci0: QCA Product ID   :0x00000016
[   14.781583] Bluetooth: hci0: QCA SOC Version  :0x20180100
[   14.785926] Bluetooth: hci0: QCA ROM Version  :0x00000100
[   14.791546] Bluetooth: hci0: QCA Patch Version:0x00003ded
[   14.796698] Bluetooth: hci0: QCA controller version 0x01000100
[   14.802217] Bluetooth: hci0: QCA Downloading qca/mpnv10.bin
[   16.393850] Bluetooth: hci0: QCA Build Info: BTFW.MAPLE.1.0.0-00102-MPL_ROM_PATCHZ-1

Best regards,
George Moussalem

Signed-off-by: George Moussalem <[email protected]>
---
Changes in v2:
- removed unused struct member btss_reset from m0_btss struct.
- used devm_reset_control_get_exclusive_deasserted to acquire and
  deassert btss_reset in one call. No need to explicitly assert upon
  unbind since devres will handle it.
- As per Bjorn's comments, collapsed the rproc and BT driver into one
  which now handles firmware loading and transport.
- As per further review comments and above change, squashed the two
  devicetree bindings into one to represent the Bluetooth controller
- Added new SCM call to drive Bluetooth power modes. Based on testing on
  more router boards, this is required during start/stop sequences to
  avoid the controller hanging. This is only supported on relatively
  newer QSEE versions, so the SCM call is checked for availability
  before use.
- Refactored resource lifecycle management in the driver so that IRQ and
  work queue are managed at the driver level (probe/remove) while FW
  loading and powering on/off the controller is handled upon hdev
  open/close.
- Consolidated TX send functions for custom IPC and HCI frames into one
  and solved a potential NULL pointer dereference issue under TX
  pressure.
- Replace code to load and initialize firmware metadate by existing
  qcom_mdt_pas_init function. 
- Solved an off byone calculation error in the RX parser.
- Added entry to MAINTAINERS file
- Link to v1: https://lore.kernel.org/r/[email protected]

---
George Moussalem (6):
      dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller
      Bluetooth: btqca: Add IPQ5018 support
      firmware: qcom: scm: Add support for setting Bluetooth power modes
      Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver
      arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support
      MAINTAINERS: Add entry for Qualcomm IPQ5018 Bluetooth driver

 .../bindings/net/bluetooth/qcom,ipq5018-bt.yaml    |   86 ++
 MAINTAINERS                                        |    7 +
 arch/arm64/boot/dts/qcom/ipq5018.dtsi              |   25 +-
 drivers/bluetooth/Kconfig                          |   11 +
 drivers/bluetooth/Makefile                         |    1 +
 drivers/bluetooth/btqca.c                          |   16 +
 drivers/bluetooth/btqca.h                          |    3 +
 drivers/bluetooth/btqcomipc.c                      | 1052 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |   49 +
 drivers/firmware/qcom/qcom_scm.h                   |    1 +
 include/linux/firmware/qcom/qcom_scm.h             |    1 +
 11 files changed, 1251 insertions(+), 1 deletion(-)
---
base-commit: 4d1ab324fcb7d20df5a071edb0304461846fdc12
change-id: 20260625-ipq5018-bluetooth-06ff66c9d753
prerequisite-message-id: <[email protected]>
prerequisite-patch-id: 6ce8686c1683f468d86b4502f5ec9d19c392a382
prerequisite-patch-id: e362f7fcbacff716b7ef720e6780786a7d88c013
prerequisite-patch-id: 9168930e40551e842c8171d5433a6f39ad4b78a4
prerequisite-patch-id: 64fecfbd1e085d7d2ab0ae23295ca34ec8e14c5e
prerequisite-patch-id: 566804aaa690ee9aa285d0fd75fd16d94fbadebf
prerequisite-patch-id: dc18bec338f54b3051f4523f9d1d3c0566a20ccd
prerequisite-patch-id: b6b3eb46429936ab49423d295433daf47981db0f
prerequisite-patch-id: 75caa99e3bbcdf41b6462b9f5f703bea1d4a65fa
prerequisite-patch-id: 35e9968f482f78ca233eb0306d9c5fdbff093175

Best regards,
-- 
George Moussalem <[email protected]>
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.