[PATCH 1/3] dt-bindings: interrupt-controller: ti,irq-crossbar: Convert to DT schema

Convert TI irq-crossbar binding from text format to DT schema.

As part of conversion following changes are made:
 - Add '#interrupt-cells' as a required property which was missing in
   text binding
 - As irq-crossbar is interrupt-controller. Move binding from
   bindings/arm/omap to bindings/interrupt-controller
 - property ti,irqs-reserved is defined and used as a array but other
   binding ti,pruss-intc.yaml uses same property name as a unit8 bitmask
   which causes erros in dt_binding_check. Update ti,irqs-reserved
   property name to ti,crossbar-irqs-reserved to resolve duplicate naming.

Signed-off-by: Bhargav Joshi <[email protected]>
---
 .../devicetree/bindings/arm/omap/crossbar.txt      | 55 ------------
 .../interrupt-controller/ti,irq-crossbar.yaml      | 98 ++++++++++++++++++++++
 2 files changed, 98 insertions(+), 55 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
deleted file mode 100644
index a43e4c7aba3d..000000000000
--- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt
+++ /dev/null
@@ -1,55 +0,0 @@
-Some socs have a large number of interrupts requests to service
-the needs of its many peripherals and subsystems. All of the
-interrupt lines from the subsystems are not needed at the same
-time, so they have to be muxed to the irq-controller appropriately.
-In such places a interrupt controllers are preceded by an CROSSBAR
-that provides flexibility in muxing the device requests to the controller
-inputs.
-
-Required properties:
-- compatible : Should be "ti,irq-crossbar"
-- reg: Base address and the size of the crossbar registers.
-- interrupt-controller: indicates that this block is an interrupt controller.
-- ti,max-irqs: Total number of irqs available at the parent interrupt controller.
-- ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed.
-- ti,reg-size: Size of a individual register in bytes. Every individual
-	    register is assumed to be of same size. Valid sizes are 1, 2, 4.
-- ti,irqs-reserved: List of the reserved irq lines that are not muxed using
-		 crossbar. These interrupt lines are reserved in the soc,
-		 so crossbar bar driver should not consider them as free
-		 lines.
-
-Optional properties:
-- ti,irqs-skip: This is similar to "ti,irqs-reserved", but these are for
-  SOC-specific hard-wiring of those irqs which unexpectedly bypasses the
-  crossbar. These irqs have a crossbar register, but still cannot be used.
-
-- ti,irqs-safe-map: integer which maps to a safe configuration to use
-  when the interrupt controller irq is unused (when not provided, default is 0)
-
-Examples:
-		crossbar_mpu: crossbar@4a002a48 {
-			compatible = "ti,irq-crossbar";
-			reg = <0x4a002a48 0x130>;
-			ti,max-irqs = <160>;
-			ti,max-crossbar-sources = <400>;
-			ti,reg-size = <2>;
-			ti,irqs-reserved = <0 1 2 3 5 6 131 132>;
-			ti,irqs-skip = <10 133 139 140>;
-		};
-
-Consumer:
-========
-See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and
-Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml for
-further details.
-
-An interrupt consumer on an SoC using crossbar will use:
-	interrupts = <GIC_SPI request_number interrupt_level>
-
-Example:
-	device_x@4a023000 {
-		/* Crossbar 8 used */
-		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		...
-	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,irq-crossbar.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,irq-crossbar.yaml
new file mode 100644
index 000000000000..b31e147c2672
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,irq-crossbar.yaml
@@ -0,0 +1,98 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/ti,irq-crossbar.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments IRQ Crossbar
+
+maintainers:
+  - Sricharan R <[email protected]>
+
+description:
+  Some socs have a large number of interrupts requests to service the needs of
+  its many peripherals and subsystems. All of the interrupt lines from the
+  subsystems are not needed at the same time, so they have to be muxed to the
+  irq-controller appropriately. In such places a interrupt controllers are
+  preceded by an CROSSBAR that provides flexibility in muxing the device
+  requests to the controller inputs.
+
+properties:
+  compatible:
+    const: ti,irq-crossbar
+
+  reg:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 3
+
+  ti,max-irqs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Total number of irqs available at the parent interrupt controller.
+    minimum: 1
+
+  ti,max-crossbar-sources:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Maximum number of crossbar sources that can be routed.
+    minimum: 1
+
+  ti,reg-size:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Size of a individual register in bytes. Every individual
+      register is assumed to be of same size.
+    enum: [1, 2, 4]
+
+  ti,crossbar-irqs-reserved:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      List of the reserved irq lines that are not muxed using crossbar. These
+      interrupt lines are reserved in the soc, so crossbar bar driver should not
+      consider them as free lines.
+
+  ti,irqs-skip:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      Similar to "ti,crossbar-irqs-reserved", but these are for SOC-specific hard-wiring
+      of those irqs which unexpectedly bypasses the crossbar. These irqs have a
+      crossbar register, but still cannot be used.
+
+  ti,irqs-safe-map:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      integer which maps to a safe configuration to use when the interrupt
+      controller irq is unused.
+    default: 0
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - '#interrupt-cells'
+  - ti,max-irqs
+  - ti,max-crossbar-sources
+  - ti,reg-size
+  - ti,crossbar-irqs-reserved
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    crossbar_mpu: crossbar@4a002a48 {
+        compatible = "ti,irq-crossbar";
+        reg = <0x4a002a48 0x130>;
+        interrupt-controller;
+        #interrupt-cells = <3>;
+        ti,max-irqs = <160>;
+        ti,max-crossbar-sources = <400>;
+        ti,reg-size = <2>;
+        ti,crossbar-irqs-reserved = <0 1 2 3 5 6 131 132>;
+        ti,irqs-skip = <10 133 139 140>;
+    };

-- 
2.54.0