[PATCH v6 0/6] OpenRISC de0 nano single and multicore boards

Since v5:
 - Adjust dt-binding patch based on suggestions from Geert and Krzysztof.
 - Add reviewed-by's on the dt-binding patch.
Since v4:
 - Rebased the series on linux-next to allow patches to be incremental.
 - Rewrote the dt-bindings patch as an incremental patch, Due to this I
   dropped reviewed-by's.
 - Added acked-by to the IPI fix patch.
Since v3:
 - Switch order of gpio-mmio driver and bindings patches to patch binding
   first before driver.  Suggested by Krzysztof.
 - Removed example form binding suggested by Krzysztof.
 - Added Reviewed-by's from Geert and Linus W.
Since v2:
 - Fixup (replace) gpio-mmio patch to update driver compatible list and just add
   opencores,gpio to mmio-gpio bindings.  Discussed with Geert and Linus W
   because the 8-bit opencores,gpio is not the same as the 32-bit broadcom
   chip. [1].
 - Update new device trees to use proper ordering, remove debug options, remove
   unneeded "status" properties.  Suggested by Geert.
Since v1:
 - Use proper schema in gpio-mmio suggsted by Conor Dooley
 - Remove 0 clock-frequency definitions in dtsi file

The patches add support for OpenRISC systems running on the De0 Nano FPGA
development board.  We have two SoCs which are available here:

 - https://github.com/olofk/de0_nano - Single core
 - https://github.com/stffrdhrn/de0_nano-multicore - Multicore

As I work on tutorials [2] to help other get started with OpenRISC I would like to
have these defconfig and devicetree definitions in the upstream kernel to avoid
losing them.

When I was working on resurrecting these old setup's I found a major bug in
OpenRISC SMP which is fixed in this series as well.

[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://openrisc.io/tutorials/

Stafford Horne (6):
  dt-bindings: gpio-mmio: Correct opencores GPIO
  gpio: mmio: Add compatible for opencores GPIO
  openrisc: dts: Add de0 nano config and devicetree
  openrisc: Fix IPIs on simple multicore systems
  openrisc: dts: Split simple smp dts to dts and dtsi
  openrisc: dts: Add de0 nano multicore config and devicetree

 .../devicetree/bindings/gpio/gpio-mmio.yaml   | 16 ++--
 arch/openrisc/boot/dts/de0-nano-common.dtsi   | 42 +++++++++
 arch/openrisc/boot/dts/de0-nano-multicore.dts | 25 +++++
 arch/openrisc/boot/dts/de0-nano.dts           | 54 +++++++++++
 arch/openrisc/boot/dts/simple-smp.dts         | 25 +++++
 .../dts/{simple_smp.dts => simple-smp.dtsi}   | 11 +--
 arch/openrisc/configs/de0_nano_defconfig      | 79 ++++++++++++++++
 .../configs/de0_nano_multicore_defconfig      | 92 +++++++++++++++++++
 arch/openrisc/configs/simple_smp_defconfig    |  2 +-
 arch/openrisc/include/asm/smp.h               |  3 +-
 arch/openrisc/kernel/smp.c                    | 22 ++++-
 drivers/gpio/gpio-mmio.c                      |  1 +
 drivers/irqchip/irq-ompic.c                   | 15 ++-
 drivers/irqchip/irq-or1k-pic.c                | 27 +++++-
 14 files changed, 390 insertions(+), 24 deletions(-)
 create mode 100644 arch/openrisc/boot/dts/de0-nano-common.dtsi
 create mode 100644 arch/openrisc/boot/dts/de0-nano-multicore.dts
 create mode 100644 arch/openrisc/boot/dts/de0-nano.dts
 create mode 100644 arch/openrisc/boot/dts/simple-smp.dts
 rename arch/openrisc/boot/dts/{simple_smp.dts => simple-smp.dtsi} (90%)
 create mode 100644 arch/openrisc/configs/de0_nano_defconfig
 create mode 100644 arch/openrisc/configs/de0_nano_multicore_defconfig

-- 
2.51.0