[PATCH v7 3/3] arm64: dts: qcom: eliza-evk: Add PCIe1 with TC9563 PCIe switch

The Eliza EVK board connects PCIe1 (8GT/s x2) to a Toshiba TC9563
PCIe switch. Enable PCIe1 and its QMP PHY nodes.

TC9563 uses I2C (at address 0x77 on I2C4) for its management interface.

Override the base iommu-map with the expanded set covering all the
switch's downstream ports (0x1400-0x1408 SID range).

The TC9563 RESX# and PERST# are OR-ed internally to assert reset on the
switch. Use TC9563 RESX# pin via a TLMM GPIO and skip wiring PERST#
from the PCIe controller.

Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Bartosz Golaszewski <[email protected]>
Reviewed-by: Abel Vesa <[email protected]>
Reviewed-by: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Krishna Chaitanya Chundru <[email protected]>
---
 arch/arm64/boot/dts/qcom/eliza-evk.dtsi | 105 ++++++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
index b35fffb50976..ccd6f0113513 100644
--- a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
+++ b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
@@ -12,6 +12,26 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	vreg_0p9: regulator-0v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREG_0P9";
+
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_1p8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREG_1P8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vreg_pcie_m_3p3: regulator-3p3 {
 		compatible = "regulator-fixed";
 
@@ -99,6 +119,91 @@ pcieport0_ep: endpoint {
 	};
 };
 
+&pcie1 {
+	iommu-map = <0x0 &apps_smmu 0x1400 0x0 0x1>,
+		    <0x100 &apps_smmu 0x1401 0x0 0x1>,
+		    <0x208 &apps_smmu 0x1402 0x0 0x1>,
+		    <0x210 &apps_smmu 0x1403 0x0 0x1>,
+		    <0x218 &apps_smmu 0x1404 0x0 0x1>,
+		    <0x300 &apps_smmu 0x1405 0x0 0x1>,
+		    <0x400 &apps_smmu 0x1406 0x0 0x1>,
+		    <0x500 &apps_smmu 0x1407 0x0 0x1>,
+		    <0x501 &apps_smmu 0x1408 0x0 0x1>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l1k>;
+	vdda-pll-supply = <&vreg_l3k>;
+
+	status = "okay";
+};
+
+&pcie1_port0 {
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+	/* Same GPIO is used for both PERST# and resx-gpio */
+
+	tc9563: pcie@0,0 {
+		compatible = "pci1179,0623";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		device_type = "pci";
+		ranges;
+		bus-range = <0x2 0xff>;
+
+		vddc-supply = <&vreg_0p9>;
+		vdd18-supply = <&vreg_1p8>;
+		vdd09-supply = <&vreg_0p9>;
+		vddio1-supply = <&vreg_1p8>;
+		vddio2-supply = <&vreg_1p8>;
+		vddio18-supply = <&vreg_1p8>;
+
+		i2c-parent = <&i2c4 0x77>;
+
+		resx-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+		pcie@1,0 {
+			reg = <0x20800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x3 0xff>;
+		};
+
+		pcie@2,0 {
+			reg = <0x21000 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x4 0xff>;
+		};
+
+		pcie@3,0 {
+			reg = <0x21800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges;
+			bus-range = <0x5 0xff>;
+
+			ethernet@0,0 {
+				reg = <0x50000 0x0 0x0 0x0 0x0>;
+			};
+
+			ethernet@0,1 {
+				reg = <0x50100 0x0 0x0 0x0 0x0>;
+			};
+		};
+	};
+};
+
 &uart13 {
 	compatible = "qcom,geni-debug-uart";
 

-- 
2.34.1