[PATCH v5 0/3] arm64: dts: qcom: eliza-evk: Enable PCIe0 and PCIe1 with M.2 and TC9563 switch
Krishna Chaitanya Chundru <[email protected]>
| Newsgroups | org.kernel.vger.linux-pm,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel,org.kernel.vger.linux-pci |
|---|---|
| Message-ID | <[email protected]> |
This series enables PCIe for the Eliza EVK board (CQS SoM on EVK carrier). The Eliza EVK exposes two PCIe ports: - PCIe0 drives an M.2 E key connector. The 3.3V supply is GPIO-controlled via a TCA9538 I/O expander on I2C4. The slot hosts a WLAN module (connected over PCIe) and a Bluetooth device (connected over UART5), modelled with the pcie-m2-e-connector binding. - PCIe1 (8GT/s x2) connects to a Toshiba TC9563 PCIe switch, whose management interface sits on I2C4 (address 0x77). The TC9563 RESX# and PERST# lines are OR-ed internally; reset is driven via a TLMM GPIO on the RESX# pin. The iommu-map covers all downstream switch ports (SID range 0x1400-0x1408). The M.2 WLAN module carries a Qualcomm QCC2072 Bluetooth chip. A device-ID entry is added to the M.2 power sequencer so the serdev node for the BT UART interface is created on PCI enumeration. This seris Depends-on: https://lore.kernel.org/all/[email protected]/ https://lore.kernel.org/all/20260630-dts-qcom-eliza-mtp-evk-add-pmics-v1-1-f4f320f7c88b@oss.qualcomm.com/ Signed-off-by: Krishna Chaitanya Chundru <[email protected]> --- Changes in v5: - change from pci to pcie for subnode names (konrad) - Link to v4: https://patch.msgid.link/[email protected] Changes in v4: - Added new line and used pcie port names as pcieN_portM (Konrad). - Link to v3: https://patch.msgid.link/[email protected] Changes in v3: - Clubbed pcie nodes to this series (Bjorn A) (https://lore.kernel.org/all/[email protected]/) - Added comment for PERST (Mani). - Extended ranges property for pcie1 (Konrad). - Link to v2: https://patch.msgid.link/[email protected] Changes in v2: - Drop patch 3, as this is already applied - Rebase on top of https://lore.kernel.org/all/[email protected]/ and remove pincntrl as pincntrl is added in the eliza.dtsi patch and also remove pinctrl for resx as this is covered in pcie1_default_state as perst gpio. - Link to v1: https://patch.msgid.link/[email protected] --- Krishna Chaitanya Chundru (3): arm64: dts: qcom: eliza: Add PCIe PHY and controller nodes arm64: dts: qcom: eliza-evk: Add PCIe0 with M.2 E key connector arm64: dts: qcom: eliza-evk: Add PCIe1 with TC9563 PCIe switch arch/arm64/boot/dts/qcom/eliza-evk.dtsi | 229 ++++++++++++++++++ arch/arm64/boot/dts/qcom/eliza.dtsi | 415 +++++++++++++++++++++++++++++++- 2 files changed, 642 insertions(+), 2 deletions(-) --- base-commit: dc59e4fea9d83f03bad6bddf3fa2e52491777482 change-id: 20260629-eliza_evk-6f30686b161f prerequisite-patch-id: 9e10dfbe360941cdac0300aaf163149755952f9f prerequisite-patch-id: fecce0170351baf00cbe8f6b302d1def4d99bbfc prerequisite-patch-id: 97cd6cb495fdd198f6de7fbe45ef32e4a638ec9c prerequisite-message-id: <20260630-dts-qcom-eliza-mtp-evk-add-pmics-v1-1-f4f320f7c88b@oss.qualcomm.com> prerequisite-patch-id: f3615b5c1e2222a2491f862a7fba3994058ecc53 Best regards, -- Krishna Chaitanya Chundru <[email protected]>