Re: [PATCH v6 2/3] arm64: dts: qcom: eliza-evk: Add PCIe0 with M.2 E key connector

On 7/30/2026 10:38 AM, Manivannan Sadhasivam wrote:
> On Thu, Jul 30, 2026 at 10:18:54AM +0530, Krishna Chaitanya Chundru wrote:
>> The Eliza EVK board features an M.2 E key connector connected to PCIe0.
>> Enable the PCIe0 root port and its QMP PHY with the necessary RPMH
>> regulator supplies. The M.2 slot's 3.3V supply rail is GPIO-controlled
>> via a TCA9538 I/O expander on I2C4.
>>
>> The M.2 E key slot hosts a WLAN card connected over PCIe and a Bluetooth
>> device connected over UART. Model the connector using the
>> pcie-m2-e-connector binding, wiring the PCIe root port and UART5 for
>> the respective interfaces.
>>
>> Reviewed-by: Konrad Dybcio <[email protected]>
>> Reviewed-by: Manivannan Sadhasivam <[email protected]>
>> Reviewed-by: Bartosz Golaszewski <[email protected]>
>> Signed-off-by: Krishna Chaitanya Chundru <[email protected]>
>> ---
>>  arch/arm64/boot/dts/qcom/eliza-evk.dtsi | 116 ++++++++++++++++++++++++++++++++
>>  1 file changed, 116 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
>> index e47b24f8b827..b35fffb50976 100644
>> --- a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
>> @@ -11,6 +11,92 @@ aliases {
>>  	chosen {
>>  		stdout-path = "serial0:115200n8";
>>  	};
>> +
>> +	vreg_pcie_m_3p3: regulator-3p3 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "vreg_3p3";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +
>> +		gpio = <&gpio_expander1 6 GPIO_ACTIVE_HIGH>;
>> +		enable-active-high;
>> +	};
>> +
>> +	connector-0 {
>> +		compatible = "pcie-m2-e-connector";
>> +		vpcie3v3-supply = <&vreg_pcie_m_3p3>;
>> +		w-disable1-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
>> +		w-disable2-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>;
> Hmm, Sashiko pointed out the polarity issue here, GPIO_ACTIVE_HIGH. Is it a
> mistake?
No it is working with active high only, it is how they connected in the HW.

- Krishna Chaitanya.
> - Mani
>
>> +
>> +		pinctrl-0 = <&m2_w_disable1>, <&m2_w_disable2>;
>> +		pinctrl-names = "default";
>> +
>> +		ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			port@0 {
>> +				reg = <0>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				m2_e_pcie_ep: endpoint@0 {
>> +					reg = <0>;
>> +					remote-endpoint = <&pcieport0_ep>;
>> +				};
>> +			};
>> +
>> +			port@3 {
>> +				reg = <3>;
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				m2_e_uart_ep: endpoint@0 {
>> +					reg = <0>;
>> +					remote-endpoint = <&uart5_ep>;
>> +				};
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&i2c4 {
>> +	pinctrl-0 = <&qup_i2c4_data_clk>;
>> +	pinctrl-names = "default";
>> +
>> +	clock-frequency = <400000>;
>> +
>> +	status = "okay";
>> +
>> +	gpio_expander1: gpio@3c {
>> +		compatible = "ti,tca9538";
>> +		#gpio-cells = <2>;
>> +		gpio-controller;
>> +		reg = <0x3c>;
>> +	};
>> +};
>> +
>> +&pcie0 {
>> +	status = "okay";
>> +};
>> +
>> +&pcie0_phy {
>> +	vdda-phy-supply = <&vreg_l1k>;
>> +	vdda-pll-supply = <&vreg_l3k>;
>> +
>> +	status = "okay";
>> +};
>> +
>> +&pcie0_port0 {
>> +	wake-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
>> +	reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
>> +
>> +	port {
>> +		pcieport0_ep: endpoint {
>> +			remote-endpoint = <&m2_e_pcie_ep>;
>> +		};
>> +	};
>>  };
>>  
>>  &uart13 {
>> @@ -18,3 +104,33 @@ &uart13 {
>>  
>>  	status = "okay";
>>  };
>> +
>> +&uart5 {
>> +	status = "okay";
>> +
>> +	port {
>> +		uart5_ep: endpoint {
>> +			remote-endpoint = <&m2_e_uart_ep>;
>> +		};
>> +	};
>> +};
>> +
>> +&pm8550vs_g_gpios {
>> +	m2_w_disable2: m2-w-disable2-state {
>> +		pins = "gpio4";
>> +		function = "normal";
>> +		input-disable;
>> +		output-enable;
>> +		bias-disable;
>> +		power-source = <2>;
>> +	};
>> +};
>> +
>> +&tlmm {
>> +	m2_w_disable1: m2-w-disable1-state {
>> +		pins = "gpio35";
>> +		function = "gpio";
>> +		drive-strength = <2>;
>> +		bias-pull-up;
>> +	};
>> +};
>>
>> -- 
>> 2.34.1
>>