[PATCH v7 9/9] arm64: dts: qcom: hamoa: Enable CDSP cooling
Gaurav Kohli <[email protected]>
| Newsgroups | org.kernel.vger.linux-pm,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-hardening,org.kernel.vger.linux-kernel,org.kernel.vger.linux-remoteproc |
|---|---|
| Message-ID | <[email protected]> |
From: Dipa Ramesh Mantre <[email protected]> Unlike the CPU, the CDSP does not throttle its speed automatically when it reaches high temperatures in hamoa. Set up CDSP cooling by throttling the cdsp, when it reaches 95°C. Add polling-delay-passive so the governor periodically evaluates the zone during passive cooling and steps up cooling levels when temperature stabilizes below the next trip. Signed-off-by: Dipa Ramesh Mantre <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Gaurav Kohli <[email protected]> --- arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 32 +++++++++++++++ arch/arm64/boot/dts/qcom/hamoa.dtsi | 63 ++++++++++++++++++++++++++++++ 2 files changed, 95 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts index 9fa86bb6438e..a146be1cb5fb 100644 --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts @@ -1684,4 +1684,36 @@ trip-point0 { }; }; }; + + nsp0-thermal { + trips { + trip-point1 { + temperature = <105000>; + }; + }; + }; + + nsp1-thermal { + trips { + trip-point1 { + temperature = <105000>; + }; + }; + }; + + nsp2-thermal { + trips { + trip-point1 { + temperature = <105000>; + }; + }; + }; + + nsp3-thermal { + trips { + trip-point1 { + temperature = <105000>; + }; + }; + }; }; diff --git a/arch/arm64/boot/dts/qcom/hamoa.dtsi b/arch/arm64/boot/dts/qcom/hamoa.dtsi index 09527dcf9576..ba453c8ca80d 100644 --- a/arch/arm64/boot/dts/qcom/hamoa.dtsi +++ b/arch/arm64/boot/dts/qcom/hamoa.dtsi @@ -23,6 +23,7 @@ #include <dt-bindings/soc/qcom,gpr.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h> +#include <dt-bindings/thermal/qcom,pas.h> #include <dt-bindings/thermal/thermal.h> / { @@ -8971,6 +8972,8 @@ remoteproc_cdsp: remoteproc@32300000 { status = "disabled"; + #cooling-cells = <3>; + glink-edge { interrupts-extended = <&ipcc IPCC_CLIENT_CDSP IPCC_MPROC_SIGNAL_GLINK_QMP @@ -9558,6 +9561,7 @@ aoss0-critical { }; thermal_nsp0: nsp0-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 1>; trips { @@ -9567,15 +9571,30 @@ trip-point0 { type = "hot"; }; + nsp0_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp0-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp0_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp1: nsp1-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 2>; trips { @@ -9585,15 +9604,30 @@ trip-point0 { type = "hot"; }; + nsp1_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp1-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp1_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp2: nsp2-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 3>; trips { @@ -9603,15 +9637,30 @@ trip-point0 { type = "hot"; }; + nsp2_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp2-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp2_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp3: nsp3-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 4>; trips { @@ -9621,12 +9670,26 @@ trip-point0 { type = "hot"; }; + nsp3_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp3-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp3_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_gpuss_0: gpuss-0-thermal { -- 2.34.1