Re: [PATCH v4 13/13] arm64: dts: qcom: Add SM7250 devicetree file

On 8/21/26 5:40 PM, Sreeshankar K wrote:
> Add base devicetree file for SM7250 SoC.
> This file adds the basic nodes like cpu, psci and other required
> configuration for booting up to the serial console.
> 
> Signed-off-by: Sreeshankar K <[email protected]>
> ---

[...]


> +		cluster_pd: power-domain-cpu-cluster0 {
> +			#power-domain-cells = <0>;
> +			domain-idle-states = <&cluster_sleep_pc
> +					      &cluster_sleep_cx
> +					      &cluster_sleep_aoss>;

nit:

<&foo>,
<&bar>,
...

(compiles to the same bytecode)

[...]

> +	soc: soc@0 {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges = <0 0 0 0 0x10 0>;
> +		dma-ranges = <0 0 0 0 0x10 0>;
> +		compatible = "simple-bus";

compatible should come first

> +
> +		gcc: clock-controller@100000 {
> +			compatible = "qcom,sm7250-gcc";
> +			reg = <0x0 0x00100000 0x0 0x1f0000>;
> +			clock-names = "bi_tcxo",
> +				      "bi_tcxo_ao",
> +				      "sleep_clk";
> +			clocks = <&rpmhcc RPMH_CXO_CLK>,
> +				 <&rpmhcc RPMH_CXO_CLK_A>,
> +				 <&sleep_clk>;
> +			power-domains = <&rpmhpd RPMHPD_CX>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +		};
> +
> +		qupv3_id_1: geniqup@9c0000 {
> +			compatible = "qcom,geni-se-qup";
> +			reg = <0x0 0x009c0000 0x0 0x6000>;
> +			clock-names = "m-ahb", "s-ahb";
> +			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> +				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			status = "disabled";

I think this wrapper can be enabled globally


> +
> +			uart2: serial@988000 {
> +				compatible = "qcom,geni-debug-uart";
> +				reg = <0 0x00988000 0 0x4000>;
> +				clock-names = "se";
> +				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
> +				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		intc: interrupt-controller@17a00000 {
> +			compatible = "arm,gic-v3";
> +			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
> +			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			interrupts = <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		pdc: interrupt-controller@b220000 {
> +			compatible = "qcom,sm7250-pdc", "qcom,pdc";
> +			reg = <0 0xb220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> +			qcom,pdc-ranges = <0 480 42>, <42 612 28>,
> +					  <70 63 1>, <71 640 15>, <86 522 52>;

1 a line, please

> +			#interrupt-cells = <2>;
> +			interrupt-parent = <&intc>;
> +			interrupt-controller;
> +		};
> +
> +		spmi_bus: spmi@c440000 {
> +			compatible = "qcom,spmi-pmic-arb";
> +			reg = <0x0 0x0c440000 0x0 0x0001100>,
> +			      <0x0 0x0c600000 0x0 0x2000000>,
> +			      <0x0 0x0e600000 0x0 0x0100000>,
> +			      <0x0 0x0e700000 0x0 0x00a0000>,
> +			      <0x0 0x0c40a000 0x0 0x0026000>;
> +			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";

and here

[...]

> +		apps_rsc: rsc@18200000 {
> +			compatible = "qcom,rpmh-rsc";
> +			reg = <0x0 0x18200000 0x0 0x10000>,
> +			      <0x0 0x18210000 0x0 0x10000>,
> +			      <0x0 0x18220000 0x0 0x10000>;
> +			reg-names = "drv-0", "drv-1", "drv-2";

and here

[...]


> +		cpufreq_hw: cpufreq@18323000 {
> +			compatible = "qcom,sm7250-cpufreq-hw", "qcom,cpufreq-hw";
> +			reg = <0 0x18323000 0 0x1000>,
> +			      <0 0x18325800 0 0x1000>,
> +			      <0 0x18327800 0 0x1000>;
> +			reg-names = "freq-domain0", "freq-domain1",
> +				    "freq-domain2";

and here

> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
> +			clock-names = "xo", "alternate";
> +			#freq-domain-cells = <1>;
> +			#clock-cells = <1>;
> +		};
> +
> +		tcsr_mutex: hwlock@1f40000 {
> +			compatible = "qcom,tcsr-mutex";
> +			reg = <0x0 0x01f40000 0x0 0x40000>;
> +			#hwlock-cells = <1>;
> +		};
> +
> +		timer@17c20000 {
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +			compatible = "arm,armv7-timer-mem";

Compatible should come as the first property

> +			reg = <0x0 0x17c20000 0x0 0x1000>;
> +			clock-frequency = <19200000>;

This line should not be necessary

Konrad