[PATCH v3 0/2] pwm: add Axiado AX3000 PWM support

This series adds support for the PWM controller found on Axiado
AX3000 and AX3005 SoCs.

A new driver is needed because this PWM controller is a SoC-specific
hardware block used on Axiado SoCs. It has its own register layout,
enable control, period configuration, duty-cycle configuration, and
does not match any existing upstream PWM driver.

The controller provides configurable PWM output signals. The driver
exposes the controller through the Linux PWM framework and supports
period and duty-cycle configuration.

The driver converts the requested period and duty cycle from nanoseconds
to hardware clock cycles based on the input clock rate.

The datasheet is not publicly available. Public high-level product
information is available at:

https://axiado.com/products/#AX3080

The register definitions and programming sequence used by this driver
are based on Axiado internal SoC documentation.

Signed-off-by: Petar Stepanovic <[email protected]>
---
Changes in v3:
- Express AX3005 compatibility with AX3000 using a fallback compatible.
- Update the Devicetree binding example accordingly.
- Add 0% duty-cycle support using the hardware constant-low encoding.
- Cache the rounded period for 0% duty-cycle waveform readback.
- Allow sub-cycle duty requests to round down to 0% instead of rounding
  up to one clock cycle.
- Normalize high-time values greater than the period to 100% duty.
- Drop the redundant AX3005 OF match entry and use the AX3000 fallback.
- Clarify comments and PWM hardware limitations.
- Link to v2: https://lore.kernel.org/r/[email protected]

Changes in v2:
- Migrated the driver from the legacy apply/get_state API to the new
  waveform ops API (round_waveform_tohw/fromhw, read/write_waveform).
- Cache the clock rate at probe and lock it with
  devm_clk_rate_exclusive_get() instead of reading it on every op.
- Improved rounding: clamp period/duty to hardware limits, reject
  non-zero duty offset, preserve exact 100% duty, round sub-cycle duty
  up to the minimum.
- Added a "Limitations" comment block documenting hardware constraints.
- Renamed macros from AX_PWM_* to AXIADO_PWM_* and dropped unused ones.
- DT binding: dropped clock-names, made #pwm-cells required, and
  updated the description and compatible list to cover both the AX3000
  and AX3005 SoCs.
- Added axiado,ax3005-pwm to the driver's OF device match table.
- Link to v1: https://lore.kernel.org/r/[email protected]

To: Petar Stepanovic <[email protected]>
To: Akhila Kavi <[email protected]>
To: Prasad Bolisetty <[email protected]>
To: Uwe Kleine-König <[email protected]>
To: Rob Herring <[email protected]>
To: Krzysztof Kozlowski <[email protected]>
To: Conor Dooley <[email protected]>
To: Harshit Shah <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]

---
Petar Stepanovic (2):
      dt-bindings: pwm: add Axiado AX3000 PWM
      pwm: add Axiado AX3000 PWM driver

 .../devicetree/bindings/pwm/axiado,ax3000-pwm.yaml |  53 ++++
 MAINTAINERS                                        |   9 +
 drivers/pwm/Kconfig                                |  11 +
 drivers/pwm/Makefile                               |   1 +
 drivers/pwm/pwm-axiado.c                           | 310 +++++++++++++++++++++
 5 files changed, 384 insertions(+)
---
base-commit: 368d34807e6d04bb2089918383b58abf40e720a0
change-id: 20260518-axiado-ax3000-pwm-cd7c346849f1

Best regards,
--  
Petar Stepanovic <[email protected]>