Re: [PATCH net] net/mlx5e: fix BQL reset on SQ re-activation

On 29/07/2026 0:47, Bobby Eshleman wrote:
> From: Bobby Eshleman <[email protected]>
> 
> mlx5e_queue_start() deactivates and re-activates all channels but closes
> only the queue being restarted. mlx5e_activate_txqsq() then
> unconditionally calls netdev_tx_reset_queue(), zeroing the BQL counters
> of channels that kept their in-flight TX WQEs. The next completion then
> over-charges and trips the BUG_ON() in dql_completed():
> 
>    kernel BUG at lib/dynamic_queue_limits.c:99!
>    RIP: 0010:dql_completed+0x23d/0x280
>    Call Trace:
>     <IRQ>
>     mlx5e_poll_tx_cq+0x668/0xa60
>     mlx5e_napi_poll+0x5b/0x7b0
>     net_rx_action+0x15a/0x580
> 
> Reset BQL only when the SQ has no bytes in flight (sq->cc == sq->pc).
> 
> In the case that reset is skipped, the outstanding WQEs will eventually
> complete and rebalance the dql. The dql->limit is carried across the
> reset.
> 
> Fixes: b2588ea40ec9 ("net/mlx5e: Implement queue mgmt ops and single channel swap")
> Signed-off-by: Bobby Eshleman <[email protected]>
> ---
>   drivers/net/ethernet/mellanox/mlx5/core/en_main.c | 4 +++-
>   drivers/net/ethernet/mellanox/mlx5/core/en_tx.c   | 3 ++-
>   2 files changed, 5 insertions(+), 2 deletions(-)
> 

Thanks for your patch.

Overall the fix LGTM, just one comment below.

> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
> index 4a8351f95b27..44834890a409 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
> @@ -1940,7 +1940,9 @@ void mlx5e_activate_txqsq(struct mlx5e_txqsq *sq)
>   {
>   	sq->txq = netdev_get_tx_queue(sq->netdev, sq->txq_ix);
>   	set_bit(MLX5E_SQ_STATE_ENABLED, &sq->state);
> -	netdev_tx_reset_queue(sq->txq);
> +	/* Reset BQL only when the SQ has no bytes in flight. */
> +	if (sq->cc == sq->pc)
> +		netdev_tx_reset_queue(sq->txq);
>   	netif_tx_start_queue(sq->txq);
>   	netif_queue_set_napi(sq->netdev, sq->txq_ix, NETDEV_QUEUE_TYPE_TX, sq->cq.napi);
>   }
> diff --git a/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c b/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c
> index 0b5e600e4a6a..d0ad1b8d6988 100644
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en_tx.c
> @@ -909,7 +909,8 @@ void mlx5e_free_txqsq_descs(struct mlx5e_txqsq *sq)
>   	sq->cc = sqcc;
>   
>   	/* Do not update BQL for TXQs that got replaced by new active ones, as
> -	 * netdev_tx_reset_queue() is called for them in mlx5e_activate_txqsq().
> +	 * netdev_tx_reset_queue() is called for them in mlx5e_activate_txqsq()
> +	 * if the queue has zero in-flight WQEs.
>   	 */

Please drop this hunk. In this path the replacement SQ is always freshly 
created, so cc == pc == 0 and the reset always happens - the qualifier 
invites the reader to worry about a case that cannot occur here. The 
original wording is accurate as-is.

>   	if (sq == sq->priv->txq2sq[sq->txq_ix])
>   		netdev_tx_completed_queue(sq->txq, npkts, nbytes);
> 
> ---
> base-commit: b515dc54795ef370be3cb396e7c12ad91686b6d1
> change-id: 20260728-mlx5-bql-84e02a5a46c8
> 
> Best regards,