[PATCH v4 for-next 20/24] RDMA/hfi2: Add misc header files
Dennis Dalessandro <[email protected]>
| Newsgroups | org.kernel.vger.linux-rdma |
|---|---|
| Message-ID | <178612544736.3164235.17215043296283337580.stgit@awdrv-04> |
There are a few header files that didn't really fit with the rest of the bunch so adding them all separately. Co-developed-by: Dean Luick <[email protected]> Signed-off-by: Dean Luick <[email protected]> Assisted-by: Claude:claude-sonnet-4-5 Signed-off-by: Dennis Dalessandro <[email protected]> --- drivers/infiniband/hw/hfi2/opfn.h | 88 ++++++++ drivers/infiniband/hw/hfi2/platform.h | 372 +++++++++++++++++++++++++++++++++ drivers/infiniband/hw/hfi2/qsfp.h | 202 ++++++++++++++++++ 3 files changed, 662 insertions(+) create mode 100644 drivers/infiniband/hw/hfi2/opfn.h create mode 100644 drivers/infiniband/hw/hfi2/platform.h create mode 100644 drivers/infiniband/hw/hfi2/qsfp.h diff --git a/drivers/infiniband/hw/hfi2/opfn.h b/drivers/infiniband/hw/hfi2/opfn.h new file mode 100644 index 000000000000..87fad4e7286e --- /dev/null +++ b/drivers/infiniband/hw/hfi2/opfn.h @@ -0,0 +1,88 @@ +/* SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) */ +/* + * Copyright(c) 2018 Intel Corporation. + * Copyright(c) 2025-2026 Cornelis Networks, Inc. + * + */ +#ifndef _HFI2_OPFN_H +#define _HFI2_OPFN_H + +/** + * DOC: Omni Path Feature Negotion (OPFN) + * + * OPFN is a discovery protocol for Intel Omni-Path fabric that + * allows two RC QPs to negotiate a common feature that both QPs + * can support. Currently, the only OPA feature that OPFN + * supports is TID RDMA. + * + * Architecture + * + * OPFN involves the communication between two QPs on the HFI + * level on an Omni-Path fabric, and ULPs have no knowledge of + * OPFN at all. + * + * Implementation + * + * OPFN extends the existing IB RC protocol with the following + * changes: + * -- Uses Bit 24 (reserved) of DWORD 1 of Base Transport + * Header (BTH1) to indicate that the RC QP supports OPFN; + * -- Uses a combination of RC COMPARE_SWAP opcode (0x13) and + * the address U64_MAX (0xFFFFFFFFFFFFFFFF) as an OPFN + * request; The 64-bit data carried with the request/response + * contains the parameters for negotiation and will be + * defined in tid_rdma.c file; + * -- Defines IB_WR_RESERVED3 as IB_WR_OPFN. + * + * The OPFN communication will be triggered when an RC QP + * receives a request with Bit 24 of BTH1 set. The responder QP + * will then post send an OPFN request with its local + * parameters, which will be sent to the requester QP once all + * existing requests on the responder QP side have been sent. + * Once the requester QP receives the OPFN request, it will + * keep a copy of the responder QP's parameters, and return a + * response packet with its own local parameters. The responder + * QP receives the response packet and keeps a copy of the requester + * QP's parameters. After this exchange, each side has the parameters + * for both sides and therefore can select the right parameters + * for future transactions + */ + +#include <linux/workqueue.h> +#include <rdma/ib_verbs.h> +#include <rdma/rdmavt_qp.h> + +/* STL Verbs Extended */ +#define IB_BTHE_E_SHIFT 24 +#define HFI2_VERBS_E_ATOMIC_VADDR U64_MAX + +enum hfi2_opfn_codes { + STL_VERBS_EXTD_NONE = 0, + STL_VERBS_EXTD_TID_RDMA, + STL_VERBS_EXTD_MAX +}; + +struct hfi2_opfn_data { + u8 extended; + u16 requested; + u16 completed; + enum hfi2_opfn_codes curr; + /* serialize opfn function calls */ + spinlock_t lock; + struct work_struct opfn_work; +}; + +/* WR opcode for OPFN */ +#define IB_WR_OPFN IB_WR_RESERVED3 + +void hfi2_opfn_send_conn_request(struct work_struct *work); +void hfi2_opfn_conn_response(struct rvt_qp *qp, struct rvt_ack_entry *e, + struct ib_atomic_eth *ateth); +void hfi2_opfn_conn_reply(struct rvt_qp *qp, u64 data); +void hfi2_opfn_conn_error(struct rvt_qp *qp); +void hfi2_opfn_qp_init(struct rvt_qp *qp, struct ib_qp_attr *attr, int attr_mask); +void hfi2_opfn_trigger_conn_request(struct rvt_qp *qp, u32 bth1); +int hfi2_opfn_init(void); +void hfi2_opfn_exit(void); + +#endif /* _HFI2_OPFN_H */ diff --git a/drivers/infiniband/hw/hfi2/platform.h b/drivers/infiniband/hw/hfi2/platform.h new file mode 100644 index 000000000000..5ae163520a8a --- /dev/null +++ b/drivers/infiniband/hw/hfi2/platform.h @@ -0,0 +1,372 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */ +/* + * Copyright(c) 2015, 2016 Intel Corporation. + * Copyright(c) 2025-2026 Cornelis Networks, Inc. + */ + +#ifndef __PLATFORM_H +#define __PLATFORM_H + +#define METADATA_TABLE_FIELD_START_SHIFT 0 +#define METADATA_TABLE_FIELD_START_LEN_BITS 15 +#define METADATA_TABLE_FIELD_LEN_SHIFT 16 +#define METADATA_TABLE_FIELD_LEN_LEN_BITS 16 + +/* Header structure */ +#define PLATFORM_CONFIG_HEADER_RECORD_IDX_SHIFT 0 +#define PLATFORM_CONFIG_HEADER_RECORD_IDX_LEN_BITS 6 +#define PLATFORM_CONFIG_HEADER_TABLE_LENGTH_SHIFT 16 +#define PLATFORM_CONFIG_HEADER_TABLE_LENGTH_LEN_BITS 12 +#define PLATFORM_CONFIG_HEADER_TABLE_TYPE_SHIFT 28 +#define PLATFORM_CONFIG_HEADER_TABLE_TYPE_LEN_BITS 4 + +enum platform_config_table_type_encoding { + PLATFORM_CONFIG_TABLE_RESERVED, + PLATFORM_CONFIG_SYSTEM_TABLE, + PLATFORM_CONFIG_PORT_TABLE, + PLATFORM_CONFIG_RX_PRESET_TABLE, + PLATFORM_CONFIG_TX_PRESET_TABLE, + PLATFORM_CONFIG_QSFP_ATTEN_TABLE, + PLATFORM_CONFIG_VARIABLE_SETTINGS_TABLE, + PLATFORM_CONFIG_TABLE_MAX +}; + +enum platform_config_system_table_fields { + SYSTEM_TABLE_RESERVED, + SYSTEM_TABLE_NODE_STRING, + SYSTEM_TABLE_SYSTEM_IMAGE_GUID, + SYSTEM_TABLE_NODE_GUID, + SYSTEM_TABLE_REVISION, + SYSTEM_TABLE_VENDOR_OUI, + SYSTEM_TABLE_META_VERSION, + SYSTEM_TABLE_DEVICE_ID, + SYSTEM_TABLE_PARTITION_ENFORCEMENT_CAP, + SYSTEM_TABLE_QSFP_POWER_CLASS_MAX, + SYSTEM_TABLE_QSFP_ATTENUATION_DEFAULT_12G, + SYSTEM_TABLE_QSFP_ATTENUATION_DEFAULT_25G, + SYSTEM_TABLE_VARIABLE_TABLE_ENTRIES_PER_PORT, + SYSTEM_TABLE_MAX +}; + +enum platform_config_port_table_fields { + PORT_TABLE_RESERVED, + PORT_TABLE_PORT_TYPE, + PORT_TABLE_LOCAL_ATTEN_12G, + PORT_TABLE_LOCAL_ATTEN_25G, + PORT_TABLE_LINK_SPEED_SUPPORTED, + PORT_TABLE_LINK_WIDTH_SUPPORTED, + PORT_TABLE_AUTO_LANE_SHEDDING_ENABLED, + PORT_TABLE_EXTERNAL_LOOPBACK_ALLOWED, + PORT_TABLE_VL_CAP, + PORT_TABLE_MTU_CAP, + PORT_TABLE_TX_LANE_ENABLE_MASK, + PORT_TABLE_LOCAL_MAX_TIMEOUT, + PORT_TABLE_REMOTE_ATTEN_12G, + PORT_TABLE_REMOTE_ATTEN_25G, + PORT_TABLE_TX_PRESET_IDX_ACTIVE_NO_EQ, + PORT_TABLE_TX_PRESET_IDX_ACTIVE_EQ, + PORT_TABLE_RX_PRESET_IDX, + PORT_TABLE_CABLE_REACH_CLASS, + PORT_TABLE_MAX +}; + +enum platform_config_rx_preset_table_fields { + RX_PRESET_TABLE_RESERVED, + RX_PRESET_TABLE_QSFP_RX_CDR_APPLY, + RX_PRESET_TABLE_QSFP_RX_EMP_APPLY, + RX_PRESET_TABLE_QSFP_RX_AMP_APPLY, + RX_PRESET_TABLE_QSFP_RX_CDR, + RX_PRESET_TABLE_QSFP_RX_EMP, + RX_PRESET_TABLE_QSFP_RX_AMP, + RX_PRESET_TABLE_MAX +}; + +enum platform_config_tx_preset_table_fields { + TX_PRESET_TABLE_RESERVED, + TX_PRESET_TABLE_PRECUR, + TX_PRESET_TABLE_ATTN, + TX_PRESET_TABLE_POSTCUR, + TX_PRESET_TABLE_QSFP_TX_CDR_APPLY, + TX_PRESET_TABLE_QSFP_TX_EQ_APPLY, + TX_PRESET_TABLE_QSFP_TX_CDR, + TX_PRESET_TABLE_QSFP_TX_EQ, + TX_PRESET_TABLE_MAX +}; + +enum platform_config_qsfp_attn_table_fields { + QSFP_ATTEN_TABLE_RESERVED, + QSFP_ATTEN_TABLE_TX_PRESET_IDX, + QSFP_ATTEN_TABLE_RX_PRESET_IDX, + QSFP_ATTEN_TABLE_MAX +}; + +enum platform_config_variable_settings_table_fields { + VARIABLE_SETTINGS_TABLE_RESERVED, + VARIABLE_SETTINGS_TABLE_TX_PRESET_IDX, + VARIABLE_SETTINGS_TABLE_RX_PRESET_IDX, + VARIABLE_SETTINGS_TABLE_MAX +}; + +struct platform_config { + size_t size; + const u8 *data; +}; + +struct platform_config_data { + u32 *table; + u32 *table_metadata; + u32 num_table; +}; + +/* + * This struct acts as a quick reference into the platform_data binary image + * and is populated by hfi2_parse_platform_config(...) depending on the specific + * META_VERSION + */ +struct platform_config_cache { + u8 cache_valid; + struct platform_config_data config_tables[PLATFORM_CONFIG_TABLE_MAX]; +}; + +/* This section defines default values and encodings for the + * fields defined for each table above + */ + +/* + * ===================================================== + * System table encodings + * ===================================================== + */ +#define PLATFORM_CONFIG_MAGIC_NUM 0x3d4f5041 +#define PLATFORM_CONFIG_MAGIC_NUMBER_LEN 4 + +/* + * These power classes are the same as defined in SFF 8636 spec rev 2.4 + * describing byte 129 in table 6-16, except enumerated in a different order + */ +enum platform_config_qsfp_power_class_encoding { + QSFP_POWER_CLASS_1 = 1, + QSFP_POWER_CLASS_2, + QSFP_POWER_CLASS_3, + QSFP_POWER_CLASS_4, + QSFP_POWER_CLASS_5, + QSFP_POWER_CLASS_6, + QSFP_POWER_CLASS_7 +}; + +/* + * ==================================================== + * Port table encodings + * ==================================================== + */ +enum platform_config_port_type_encoding { + PORT_TYPE_UNKNOWN, + PORT_TYPE_DISCONNECTED, + PORT_TYPE_FIXED, + PORT_TYPE_VARIABLE, + PORT_TYPE_QSFP, + PORT_TYPE_MAX +}; + +enum platform_config_link_speed_supported_encoding { + LINK_SPEED_SUPP_12G = 1, + LINK_SPEED_SUPP_25G, + LINK_SPEED_SUPP_12G_25G, + LINK_SPEED_SUPP_MAX +}; + +/* + * This is a subset (not strict) of the link downgrades + * supported. The link downgrades supported are expected + * to be supplied to the driver by another entity such as + * the fabric manager + */ +enum platform_config_link_width_supported_encoding { + LINK_WIDTH_SUPP_1X = 1, + LINK_WIDTH_SUPP_2X, + LINK_WIDTH_SUPP_2X_1X, + LINK_WIDTH_SUPP_3X, + LINK_WIDTH_SUPP_3X_1X, + LINK_WIDTH_SUPP_3X_2X, + LINK_WIDTH_SUPP_3X_2X_1X, + LINK_WIDTH_SUPP_4X, + LINK_WIDTH_SUPP_4X_1X, + LINK_WIDTH_SUPP_4X_2X, + LINK_WIDTH_SUPP_4X_2X_1X, + LINK_WIDTH_SUPP_4X_3X, + LINK_WIDTH_SUPP_4X_3X_1X, + LINK_WIDTH_SUPP_4X_3X_2X, + LINK_WIDTH_SUPP_4X_3X_2X_1X, + LINK_WIDTH_SUPP_MAX +}; + +enum platform_config_virtual_lane_capability_encoding { + VL_CAP_VL0 = 1, + VL_CAP_VL0_1, + VL_CAP_VL0_2, + VL_CAP_VL0_3, + VL_CAP_VL0_4, + VL_CAP_VL0_5, + VL_CAP_VL0_6, + VL_CAP_VL0_7, + VL_CAP_VL0_8, + VL_CAP_VL0_9, + VL_CAP_VL0_10, + VL_CAP_VL0_11, + VL_CAP_VL0_12, + VL_CAP_VL0_13, + VL_CAP_VL0_14, + VL_CAP_MAX +}; + +/* Max MTU */ +enum platform_config_mtu_capability_encoding { + MTU_CAP_256 = 1, + MTU_CAP_512 = 2, + MTU_CAP_1024 = 3, + MTU_CAP_2048 = 4, + MTU_CAP_4096 = 5, + MTU_CAP_8192 = 6, + MTU_CAP_10240 = 7 +}; + +enum platform_config_local_max_timeout_encoding { + LOCAL_MAX_TIMEOUT_10_MS = 1, + LOCAL_MAX_TIMEOUT_100_MS, + LOCAL_MAX_TIMEOUT_1_S, + LOCAL_MAX_TIMEOUT_10_S, + LOCAL_MAX_TIMEOUT_100_S, + LOCAL_MAX_TIMEOUT_1000_S +}; + +enum link_tuning_encoding { + OPA_PASSIVE_TUNING, + OPA_ACTIVE_TUNING, + OPA_UNKNOWN_TUNING +}; + +/* + * Shifts and masks for the link SI tuning values stuffed into the ASIC scratch + * registers for integrated platforms + */ +#define PORT0_PORT_TYPE_SHIFT 0 +#define PORT0_LOCAL_ATTEN_SHIFT 4 +#define PORT0_REMOTE_ATTEN_SHIFT 10 +#define PORT0_DEFAULT_ATTEN_SHIFT 32 + +#define PORT1_PORT_TYPE_SHIFT 16 +#define PORT1_LOCAL_ATTEN_SHIFT 20 +#define PORT1_REMOTE_ATTEN_SHIFT 26 +#define PORT1_DEFAULT_ATTEN_SHIFT 40 + +#define PORT0_PORT_TYPE_MASK 0xFUL +#define PORT0_LOCAL_ATTEN_MASK 0x3FUL +#define PORT0_REMOTE_ATTEN_MASK 0x3FUL +#define PORT0_DEFAULT_ATTEN_MASK 0xFFUL + +#define PORT1_PORT_TYPE_MASK 0xFUL +#define PORT1_LOCAL_ATTEN_MASK 0x3FUL +#define PORT1_REMOTE_ATTEN_MASK 0x3FUL +#define PORT1_DEFAULT_ATTEN_MASK 0xFFUL + +#define PORT0_PORT_TYPE_SMASK (PORT0_PORT_TYPE_MASK << \ + PORT0_PORT_TYPE_SHIFT) +#define PORT0_LOCAL_ATTEN_SMASK (PORT0_LOCAL_ATTEN_MASK << \ + PORT0_LOCAL_ATTEN_SHIFT) +#define PORT0_REMOTE_ATTEN_SMASK (PORT0_REMOTE_ATTEN_MASK << \ + PORT0_REMOTE_ATTEN_SHIFT) +#define PORT0_DEFAULT_ATTEN_SMASK (PORT0_DEFAULT_ATTEN_MASK << \ + PORT0_DEFAULT_ATTEN_SHIFT) + +#define PORT1_PORT_TYPE_SMASK (PORT1_PORT_TYPE_MASK << \ + PORT1_PORT_TYPE_SHIFT) +#define PORT1_LOCAL_ATTEN_SMASK (PORT1_LOCAL_ATTEN_MASK << \ + PORT1_LOCAL_ATTEN_SHIFT) +#define PORT1_REMOTE_ATTEN_SMASK (PORT1_REMOTE_ATTEN_MASK << \ + PORT1_REMOTE_ATTEN_SHIFT) +#define PORT1_DEFAULT_ATTEN_SMASK (PORT1_DEFAULT_ATTEN_MASK << \ + PORT1_DEFAULT_ATTEN_SHIFT) + +#define QSFP_MAX_POWER_SHIFT 0 +#define TX_NO_EQ_SHIFT 4 +#define TX_EQ_SHIFT 25 +#define RX_SHIFT 46 + +#define QSFP_MAX_POWER_MASK 0xFUL +#define TX_NO_EQ_MASK 0x1FFFFFUL +#define TX_EQ_MASK 0x1FFFFFUL +#define RX_MASK 0xFFFFUL + +#define QSFP_MAX_POWER_SMASK (QSFP_MAX_POWER_MASK << \ + QSFP_MAX_POWER_SHIFT) +#define TX_NO_EQ_SMASK (TX_NO_EQ_MASK << TX_NO_EQ_SHIFT) +#define TX_EQ_SMASK (TX_EQ_MASK << TX_EQ_SHIFT) +#define RX_SMASK (RX_MASK << RX_SHIFT) + +#define TX_PRECUR_SHIFT 0 +#define TX_ATTN_SHIFT 4 +#define QSFP_TX_CDR_APPLY_SHIFT 9 +#define QSFP_TX_EQ_APPLY_SHIFT 10 +#define QSFP_TX_CDR_SHIFT 11 +#define QSFP_TX_EQ_SHIFT 12 +#define TX_POSTCUR_SHIFT 16 + +#define TX_PRECUR_MASK 0xFUL +#define TX_ATTN_MASK 0x1FUL +#define QSFP_TX_CDR_APPLY_MASK 0x1UL +#define QSFP_TX_EQ_APPLY_MASK 0x1UL +#define QSFP_TX_CDR_MASK 0x1UL +#define QSFP_TX_EQ_MASK 0xFUL +#define TX_POSTCUR_MASK 0x1FUL + +#define TX_PRECUR_SMASK (TX_PRECUR_MASK << TX_PRECUR_SHIFT) +#define TX_ATTN_SMASK (TX_ATTN_MASK << TX_ATTN_SHIFT) +#define QSFP_TX_CDR_APPLY_SMASK (QSFP_TX_CDR_APPLY_MASK << \ + QSFP_TX_CDR_APPLY_SHIFT) +#define QSFP_TX_EQ_APPLY_SMASK (QSFP_TX_EQ_APPLY_MASK << \ + QSFP_TX_EQ_APPLY_SHIFT) +#define QSFP_TX_CDR_SMASK (QSFP_TX_CDR_MASK << QSFP_TX_CDR_SHIFT) +#define QSFP_TX_EQ_SMASK (QSFP_TX_EQ_MASK << QSFP_TX_EQ_SHIFT) +#define TX_POSTCUR_SMASK (TX_POSTCUR_MASK << TX_POSTCUR_SHIFT) + +#define QSFP_RX_CDR_APPLY_SHIFT 0 +#define QSFP_RX_EMP_APPLY_SHIFT 1 +#define QSFP_RX_AMP_APPLY_SHIFT 2 +#define QSFP_RX_CDR_SHIFT 3 +#define QSFP_RX_EMP_SHIFT 4 +#define QSFP_RX_AMP_SHIFT 8 + +#define QSFP_RX_CDR_APPLY_MASK 0x1UL +#define QSFP_RX_EMP_APPLY_MASK 0x1UL +#define QSFP_RX_AMP_APPLY_MASK 0x1UL +#define QSFP_RX_CDR_MASK 0x1UL +#define QSFP_RX_EMP_MASK 0xFUL +#define QSFP_RX_AMP_MASK 0x3UL + +#define QSFP_RX_CDR_APPLY_SMASK (QSFP_RX_CDR_APPLY_MASK << \ + QSFP_RX_CDR_APPLY_SHIFT) +#define QSFP_RX_EMP_APPLY_SMASK (QSFP_RX_EMP_APPLY_MASK << \ + QSFP_RX_EMP_APPLY_SHIFT) +#define QSFP_RX_AMP_APPLY_SMASK (QSFP_RX_AMP_APPLY_MASK << \ + QSFP_RX_AMP_APPLY_SHIFT) +#define QSFP_RX_CDR_SMASK (QSFP_RX_CDR_MASK << QSFP_RX_CDR_SHIFT) +#define QSFP_RX_EMP_SMASK (QSFP_RX_EMP_MASK << QSFP_RX_EMP_SHIFT) +#define QSFP_RX_AMP_SMASK (QSFP_RX_AMP_MASK << QSFP_RX_AMP_SHIFT) + +#define BITMAP_VERSION 1 +#define BITMAP_VERSION_SHIFT 44 +#define BITMAP_VERSION_MASK 0xFUL +#define BITMAP_VERSION_SMASK (BITMAP_VERSION_MASK << \ + BITMAP_VERSION_SHIFT) +#define CHECKSUM_SHIFT 48 +#define CHECKSUM_MASK 0xFFFFUL +#define CHECKSUM_SMASK (CHECKSUM_MASK << CHECKSUM_SHIFT) + +/* platform.c */ +void hfi2_get_platform_config(struct hfi2_pportdata *ppd); +void hfi2_free_platform_config(struct hfi2_devdata *dd); +void hfi2_get_port_type(struct hfi2_pportdata *ppd); +int hfi2_set_qsfp_tx(struct hfi2_pportdata *ppd, int on); +void hfi2_tune_serdes(struct hfi2_pportdata *ppd); + +#endif /*__PLATFORM_H*/ diff --git a/drivers/infiniband/hw/hfi2/qsfp.h b/drivers/infiniband/hw/hfi2/qsfp.h new file mode 100644 index 000000000000..4cf81313c579 --- /dev/null +++ b/drivers/infiniband/hw/hfi2/qsfp.h @@ -0,0 +1,202 @@ +/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */ +/* + * Copyright(c) 2015, 2016 Intel Corporation. + * Copyright(c) 2025-2026 Cornelis Networks, Inc. + */ +/* QSFP support common definitions, for hfi driver */ + +#define QSFP_DEV 0xA0 +#define QSFP_PWR_LAG_MSEC 2000 +#define QSFP_MODPRS_LAG_MSEC 20 +/* 128 byte pages, per SFF 8636 rev 2.4 */ +#define QSFP_MAX_NUM_PAGES 5 + +/* + * Below are masks for QSFP pins. Pins are the same for HFI0 and HFI2. + * _N means asserted low + */ +#define QSFP_HFI0_I2CCLK BIT(0) +#define QSFP_HFI0_I2CDAT BIT(1) +#define QSFP_HFI0_RESET_N BIT(2) +#define QSFP_HFI0_INT_N BIT(3) +#define QSFP_HFI0_MODPRST_N BIT(4) + +/* QSFP is paged at 256 bytes */ +#define QSFP_PAGESIZE 256 +/* Reads/writes cannot cross 128 byte boundaries */ +#define QSFP_RW_BOUNDARY 128 + +/* number of bytes in i2c offset for QSFP devices */ +#define __QSFP_OFFSET_SIZE 1 /* num address bytes */ +#define QSFP_OFFSET_SIZE (__QSFP_OFFSET_SIZE << 8) /* shifted value */ + +/* Defined fields that Intel requires of qualified cables */ +/* Byte 0 is Identifier, not checked */ +/* Byte 1 is reserved "status MSB" */ +#define QSFP_MONITOR_VAL_START 22 +#define QSFP_MONITOR_VAL_END 81 +#define QSFP_MONITOR_RANGE (QSFP_MONITOR_VAL_END - QSFP_MONITOR_VAL_START + 1) +#define QSFP_TX_CTRL_BYTE_OFFS 86 +#define QSFP_PWR_CTRL_BYTE_OFFS 93 +#define QSFP_CDR_CTRL_BYTE_OFFS 98 + +#define QSFP_PAGE_SELECT_BYTE_OFFS 127 +/* Byte 128 is Identifier: must be 0x0c for QSFP, or 0x0d for QSFP+ */ +#define QSFP_MOD_ID_OFFS 128 +/* + * Byte 129 is "Extended Identifier". + * For bits [7:6]: 0:1.5W, 1:2.0W, 2:2.5W, 3:3.5W + * For bits [1:0]: 0:Unused, 1:4W, 2:4.5W, 3:5W + */ +#define QSFP_MOD_PWR_OFFS 129 +/* Byte 130 is Connector type. Not Intel req'd */ +/* Bytes 131..138 are Transceiver types, bit maps for various tech, none IB */ +/* Byte 139 is encoding. code 0x01 is 8b10b. Not Intel req'd */ +/* byte 140 is nominal bit-rate, in units of 100Mbits/sec */ +#define QSFP_NOM_BIT_RATE_100_OFFS 140 +/* Byte 141 is Extended Rate Select. Not Intel req'd */ +/* Bytes 142..145 are lengths for various fiber types. Not Intel req'd */ +/* Byte 146 is length for Copper. Units of 1 meter */ +#define QSFP_MOD_LEN_OFFS 146 +/* + * Byte 147 is Device technology. D0..3 not Intel req'd + * D4..7 select from 15 choices, translated by table: + */ +#define QSFP_MOD_TECH_OFFS 147 +extern const char *const hfi2_qsfp_devtech[16]; +/* Active Equalization includes fiber, copper full EQ, and copper near Eq */ +#define QSFP_IS_ACTIVE(tech) ((0xA2FF >> ((tech) >> 4)) & 1) +/* Active Equalization includes fiber, copper full EQ, and copper far Eq */ +#define QSFP_IS_ACTIVE_FAR(tech) ((0x32FF >> ((tech) >> 4)) & 1) +/* Attenuation should be valid for copper other than full/near Eq */ +#define QSFP_HAS_ATTEN(tech) ((0x4D00 >> ((tech) >> 4)) & 1) +/* Length is only valid if technology is "copper" */ +#define QSFP_IS_CU(tech) ((0xED00 >> ((tech) >> 4)) & 1) +#define QSFP_TECH_1490 9 + +#define QSFP_OUI(oui) (((unsigned int)oui[0] << 16) | ((unsigned int)oui[1] << 8) | \ + oui[2]) +#define QSFP_OUI_AMPHENOL 0x415048 +#define QSFP_OUI_FINISAR 0x009065 +#define QSFP_OUI_GORE 0x002177 + +/* Bytes 148..163 are Vendor Name, Left-justified Blank-filled */ +#define QSFP_VEND_OFFS 148 +#define QSFP_VEND_LEN 16 +/* Byte 164 is IB Extended transceiver codes Bits D0..3 are SDR,DDR,QDR,EDR */ +#define QSFP_IBXCV_OFFS 164 +/* Bytes 165..167 are Vendor OUI number */ +#define QSFP_VOUI_OFFS 165 +#define QSFP_VOUI_LEN 3 +/* Bytes 168..183 are Vendor Part Number, string */ +#define QSFP_PN_OFFS 168 +#define QSFP_PN_LEN 16 +/* Bytes 184,185 are Vendor Rev. Left Justified, Blank-filled */ +#define QSFP_REV_OFFS 184 +#define QSFP_REV_LEN 2 +/* + * Bytes 186,187 are Wavelength, if Optical. Not Intel req'd + * If copper, they are attenuation in dB: + * Byte 186 is at 2.5Gb/sec (SDR), Byte 187 at 5.0Gb/sec (DDR) + */ +#define QSFP_ATTEN_OFFS 186 +#define QSFP_ATTEN_LEN 2 +/* + * Bytes 188,189 are Wavelength tolerance, if optical + * If copper, they are attenuation in dB: + * Byte 188 is at 12.5 Gb/s, Byte 189 at 25 Gb/s + */ +#define QSFP_CU_ATTEN_7G_OFFS 188 +#define QSFP_CU_ATTEN_12G_OFFS 189 +/* Byte 190 is Max Case Temp. Not Intel req'd */ +/* Byte 191 is LSB of sum of bytes 128..190. Not Intel req'd */ +#define QSFP_CC_OFFS 191 +#define QSFP_EQ_INFO_OFFS 193 +#define QSFP_CDR_INFO_OFFS 194 +/* Bytes 196..211 are Serial Number, String */ +#define QSFP_SN_OFFS 196 +#define QSFP_SN_LEN 16 +/* Bytes 212..219 are date-code YYMMDD (MM==1 for Jan) */ +#define QSFP_DATE_OFFS 212 +#define QSFP_DATE_LEN 6 +/* Bytes 218,219 are optional lot-code, string */ +#define QSFP_LOT_OFFS 218 +#define QSFP_LOT_LEN 2 +/* Bytes 220, 221 indicate monitoring options, Not Intel req'd */ +/* Byte 222 indicates nominal bitrate in units of 250Mbits/sec */ +#define QSFP_NOM_BIT_RATE_250_OFFS 222 +/* Byte 223 is LSB of sum of bytes 192..222 */ +#define QSFP_CC_EXT_OFFS 223 + +/* + * Interrupt flag masks + */ +#define QSFP_DATA_NOT_READY 0x01 + +#define QSFP_HIGH_TEMP_ALARM 0x80 +#define QSFP_LOW_TEMP_ALARM 0x40 +#define QSFP_HIGH_TEMP_WARNING 0x20 +#define QSFP_LOW_TEMP_WARNING 0x10 + +#define QSFP_HIGH_VCC_ALARM 0x80 +#define QSFP_LOW_VCC_ALARM 0x40 +#define QSFP_HIGH_VCC_WARNING 0x20 +#define QSFP_LOW_VCC_WARNING 0x10 + +#define QSFP_HIGH_POWER_ALARM 0x88 +#define QSFP_LOW_POWER_ALARM 0x44 +#define QSFP_HIGH_POWER_WARNING 0x22 +#define QSFP_LOW_POWER_WARNING 0x11 + +#define QSFP_HIGH_BIAS_ALARM 0x88 +#define QSFP_LOW_BIAS_ALARM 0x44 +#define QSFP_HIGH_BIAS_WARNING 0x22 +#define QSFP_LOW_BIAS_WARNING 0x11 + +#define QSFP_ATTEN_SDR(attenarray) (attenarray[0]) +#define QSFP_ATTEN_DDR(attenarray) (attenarray[1]) + +/* + * struct qsfp_data encapsulates state of QSFP device for one port. + * it will be part of port-specific data if a board supports QSFP. + * + * Since multiple board-types use QSFP, and their pport_data structs + * differ (in the chip-specific section), we need a pointer to its head. + * + * Avoiding premature optimization, we will have one work_struct per port, + * and let the qsfp_lock arbitrate access to common resources. + * + */ +struct qsfp_data { + /* Helps to find our way */ + struct hfi2_pportdata *ppd; + struct work_struct qsfp_work; + u8 cache[QSFP_MAX_NUM_PAGES * 128]; + /* protect qsfp data */ + spinlock_t qsfp_lock; + u8 check_interrupt_flags; + u8 reset_needed; + u8 limiting_active; + u8 cache_valid; + u8 cache_refresh_required; +}; + +int hfi2_refresh_qsfp_cache(struct hfi2_pportdata *ppd, + struct qsfp_data *cp); +int hfi2_get_qsfp_power_class(u8 power_byte); +int hfi2_qsfp_mod_present(struct hfi2_pportdata *ppd); +int hfi2_get_cable_info(struct hfi2_pportdata *ppd, u32 addr, u32 len, u8 *data); + +int hfi2_i2c_write(struct hfi2_pportdata *ppd, u32 target, int i2c_addr, + int offset, void *bp, int len); +int hfi2_i2c_read(struct hfi2_pportdata *ppd, u32 target, int i2c_addr, + int offset, void *bp, int len); +int hfi2_qsfp_write(struct hfi2_pportdata *ppd, u32 target, int addr, void *bp, + int len); +int hfi2_qsfp_read(struct hfi2_pportdata *ppd, u32 target, int addr, void *bp, + int len); +int hfi2_one_qsfp_read(struct hfi2_pportdata *ppd, u32 target, int addr, void *bp, + int len); +struct hfi2_asic_data; +int hfi2_set_up_i2c(struct hfi2_devdata *dd, struct hfi2_asic_data *ad); +void hfi2_clean_up_i2c(struct hfi2_devdata *dd, struct hfi2_asic_data *ad);