[PATCH v14 4/9] arm64: dts: qcom: ipq5018: add nodes to bring up q6

From: George Moussalem <[email protected]>

Enable nodes required for q6 remoteproc bring up.

Reviewed-by: Dmitry Baryshkov <[email protected]>
Signed-off-by: George Moussalem <[email protected]>
[ Change 'qcom,smem-state-names' order to resolve dt-bindings-check error ]
Reviewed-by: Konrad Dybcio <[email protected]>
Tested-by: Vignesh Viswanathan <[email protected]>
Signed-off-by: Varadarajan Narayanan <[email protected]>
---
 arch/arm64/boot/dts/qcom/ipq5018.dtsi | 66 +++++++++++++++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 4fc627b47fe7..82af532bff38 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -158,6 +158,35 @@ tz_region: tz@4ac00000 {
 			reg = <0x0 0x4ac00000 0x0 0x200000>;
 			no-map;
 		};
+
+		q6_region: wcss@4b000000 {
+			reg = <0x0 0x4b000000 0x0 0x1b00000>;
+			no-map;
+		};
+	};
+
+	wcss: smp2p-wcss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs_glb 9>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		wcss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	soc: soc@0 {
@@ -734,6 +763,43 @@ frame@b128000 {
 			};
 		};
 
+		q6v5_wcss: remoteproc@cd00000 {
+			compatible = "qcom,ipq5018-wcss-sec-pil";
+			reg = <0x0cd00000 0x10000>;
+			firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mbn";
+			interrupts-extended = <&intc GIC_SPI 291 IRQ_TYPE_EDGE_RISING>,
+					      <&wcss_smp2p_in 0 IRQ_TYPE_NONE>,
+					      <&wcss_smp2p_in 1 IRQ_TYPE_NONE>,
+					      <&wcss_smp2p_in 2 IRQ_TYPE_NONE>,
+					      <&wcss_smp2p_in 3 IRQ_TYPE_NONE>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&gcc GCC_SLEEP_CLK_SRC>,
+				 <&gcc GCC_SYS_NOC_WCSS_AHB_CLK>;
+			clock-names = "sleep",
+				      "interconnect";
+
+			qcom,smem-states = <&wcss_smp2p_out 1>,
+					   <&wcss_smp2p_out 0>;
+			qcom,smem-state-names = "stop",
+						"shutdown";
+
+			memory-region = <&q6_region>;
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+				label = "rtr";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs_glb 8>;
+			};
+		};
+
 		pcie1: pcie@80000000 {
 			compatible = "qcom,pcie-ipq5018";
 			reg = <0x80000000 0xf1d>,

-- 
2.34.1