[PATCH v8 9/9] arm64: dts: qcom: hamoa: Enable CDSP cooling
Gaurav Kohli <[email protected]>
| Newsgroups | org.kernel.vger.linux-remoteproc,org.kernel.vger.linux-arm-msm,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-hardening,org.kernel.vger.linux-kernel,org.kernel.vger.linux-pm |
|---|---|
| Message-ID | <[email protected]> |
From: Dipa Ramesh Mantre <[email protected]> Unlike the CPU, the CDSP does not throttle its speed automatically when it reaches high temperatures in hamoa. Set up CDSP cooling by throttling the cdsp, when it reaches 95°C. Add polling-delay-passive so the governor periodically evaluates the zone during passive cooling and steps up cooling levels when temperature stabilizes below the next trip. Update the NSP passive trip thresholds to 105°C to align with the higher temperature specification for Hamoa IOT. Signed-off-by: Dipa Ramesh Mantre <[email protected]> Reviewed-by: Abel Vesa <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Gaurav Kohli <[email protected]> --- arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 16 ++++++++ arch/arm64/boot/dts/qcom/hamoa.dtsi | 63 ++++++++++++++++++++++++++++++ 2 files changed, 79 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts index 9fa86bb6438e..5d9e1a1b0668 100644 --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts @@ -1685,3 +1685,19 @@ trip-point0 { }; }; }; + +&nsp0_alert0 { + temperature = <105000>; +}; + +&nsp1_alert0 { + temperature = <105000>; +}; + +&nsp2_alert0 { + temperature = <105000>; +}; + +&nsp3_alert0 { + temperature = <105000>; +}; diff --git a/arch/arm64/boot/dts/qcom/hamoa.dtsi b/arch/arm64/boot/dts/qcom/hamoa.dtsi index 09527dcf9576..ba453c8ca80d 100644 --- a/arch/arm64/boot/dts/qcom/hamoa.dtsi +++ b/arch/arm64/boot/dts/qcom/hamoa.dtsi @@ -23,6 +23,7 @@ #include <dt-bindings/soc/qcom,gpr.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h> +#include <dt-bindings/thermal/qcom,pas.h> #include <dt-bindings/thermal/thermal.h> / { @@ -8971,6 +8972,8 @@ remoteproc_cdsp: remoteproc@32300000 { status = "disabled"; + #cooling-cells = <3>; + glink-edge { interrupts-extended = <&ipcc IPCC_CLIENT_CDSP IPCC_MPROC_SIGNAL_GLINK_QMP @@ -9558,6 +9561,7 @@ aoss0-critical { }; thermal_nsp0: nsp0-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 1>; trips { @@ -9567,15 +9571,30 @@ trip-point0 { type = "hot"; }; + nsp0_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp0-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp0_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp1: nsp1-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 2>; trips { @@ -9585,15 +9604,30 @@ trip-point0 { type = "hot"; }; + nsp1_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp1-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp1_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp2: nsp2-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 3>; trips { @@ -9603,15 +9637,30 @@ trip-point0 { type = "hot"; }; + nsp2_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp2-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp2_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_nsp3: nsp3-thermal { + polling-delay-passive = <200>; thermal-sensors = <&tsens3 4>; trips { @@ -9621,12 +9670,26 @@ trip-point0 { type = "hot"; }; + nsp3_alert0: trip-point1 { + temperature = <95000>; + hysteresis = <5000>; + type = "passive"; + }; + nsp3-critical { temperature = <115000>; hysteresis = <1000>; type = "critical"; }; }; + + cooling-maps { + map0 { + trip = <&nsp3_alert0>; + cooling-device = <&remoteproc_cdsp QCOM_TMD_CDSP_SW + THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; thermal_gpuss_0: gpuss-0-thermal { -- 2.34.1