[PATCH v3 2/2] usb: dwc3: dwc3-generic-plat: Add Renesas R-Car Gen5 DWC3 xHCI USB controller glue

From: Thanh Quan <[email protected]>

The Renesas R-Car Gen5 SoC contains multiple instances of DWC3 USB
controller with glue logic wrapper around them. Extend the generic
DWC3 platform driver with Renesas R-Car Gen5 glue logic specifics.

Signed-off-by: Thanh Quan <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
---
Cc: Conor Dooley <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Krzysztof Kozlowski <[email protected]>
Cc: Rob Herring <[email protected]>
Cc: Thinh Nguyen <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
V2: Extend dwc3-generic-plat driver instead
V3: Handle maximum-speed as optional property, test for USB 3 PHY
    non-presence to determine whether the controller is USB 2 only,
    consider optional maximum-speed DT property, but if it is missing
    then default to maximum controller capabilities based on the
    presence of PHY phandles.
---
 drivers/usb/dwc3/dwc3-generic-plat.c | 60 ++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/drivers/usb/dwc3/dwc3-generic-plat.c b/drivers/usb/dwc3/dwc3-generic-plat.c
index ca69ac0eb07ce..dec89b068291a 100644
--- a/drivers/usb/dwc3/dwc3-generic-plat.c
+++ b/drivers/usb/dwc3/dwc3-generic-plat.c
@@ -71,6 +71,60 @@ static int dwc3_eic7700_init(struct dwc3_generic *dwc3g)
 	return 0;
 }
 
+static int dwc3_renesas_rcar_gen5_init(struct dwc3_generic *dwc3g)
+{
+	struct device *dev = dwc3g->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	enum usb_device_speed speed = usb_get_maximum_speed(dev);
+	bool usb2only = false;
+	void __iomem *glue;
+
+	/* Wireless USB is not supported */
+	if (speed == USB_SPEED_WIRELESS)
+		return dev_err_probe(dev, -EINVAL, "Wireless USB not supported\n");
+
+	/* No USB 3 PHY in DT means this is surely USB 2 controller */
+	if (device_property_match_string(dev, "phy-names", "usb3-phy") < 0)
+		usb2only = true;
+
+	/*
+	 * Controller can be limited to USB 2 via optional maximum-speed DT
+	 * property. If the DT property is not present, default to maximum
+	 * controller capabilities.
+	 */
+	if (speed >= USB_SPEED_LOW && speed <= USB_SPEED_HIGH)
+		usb2only = true;
+
+	glue = devm_platform_ioremap_resource_byname(pdev, "glue");
+	if (IS_ERR(glue))
+		return PTR_ERR(glue);
+
+	/*
+	 * The datasheet describes initialization procedure without full
+	 * information about the registers. Therefore, the source code is
+	 * based on the bare metal code shared by the board team.
+	 */
+	writew(0x211, glue + 0x26);
+
+	/* USB2 does need additional register programming. */
+	if (!usb2only)
+		return 0;
+
+	writew(0x11, glue + 0x81c);
+	writew(0x0, glue + 0x81a);
+	writew(0x1, glue + 0x802);
+
+	usleep_range(10000, 20000);
+
+	writew(0x0, glue + 0x802);
+	writew(0x1, glue + 0x2a);
+	writew(0x1, glue + 0x81a);
+
+	usleep_range(10000, 20000);
+
+	return 0;
+}
+
 static int dwc3_spacemit_k1_init(struct dwc3_generic *dwc3g)
 {
 	struct device *dev = dwc3g->dev;
@@ -231,11 +285,17 @@ static const struct dwc3_generic_config eic7700_dwc3 =  {
 	.properties = DWC3_DEFAULT_PROPERTIES,
 };
 
+static const struct dwc3_generic_config renesas_rcar_gen5_dwc3 = {
+	.init = dwc3_renesas_rcar_gen5_init,
+	.properties = DWC3_DEFAULT_PROPERTIES,
+};
+
 static const struct of_device_id dwc3_generic_of_match[] = {
 	{ .compatible = "spacemit,k1-dwc3", &spacemit_k1_dwc3},
 	{ .compatible = "spacemit,k3-dwc3", },
 	{ .compatible = "fsl,ls1028a-dwc3", &fsl_ls1028_dwc3},
 	{ .compatible = "eswin,eic7700-dwc3", &eic7700_dwc3},
+	{ .compatible = "renesas,rcar-gen5-dwc3", &renesas_rcar_gen5_dwc3},
 	{ .compatible = "starfive,jhb100-dwc3", },
 	{ /* sentinel */ }
 };
-- 
2.53.0