[PATCH stalld 28/52] tests: Replace init sleeps in test_affinity

Replace start_stalld followed by a fixed two-second sleep with
start_stalld_with_log in test_affinity.sh. The helper uses event-driven
wait_for_stalld_ready internally, returning as soon as the daemon logs
its first monitoring message rather than waiting a fixed interval.
Since stalld typically initializes in under half a second, this saves
approximately nine seconds across the six modified test sections.

Signed-off-by: Wander Lairson Costa <[email protected]>
---
 tests/functional/test_affinity.sh | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/tests/functional/test_affinity.sh b/tests/functional/test_affinity.sh
index 3faa199..43ab912 100755
--- a/tests/functional/test_affinity.sh
+++ b/tests/functional/test_affinity.sh
@@ -54,8 +54,8 @@ fi
 #=============================================================================
 test_section "Test 1: Default behavior (no affinity restriction)"
 
-start_stalld -f -v -l -t 5
-sleep 2
+rm -f "${STALLD_LOG}"
+start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5
 
 default_affinity=$(check_affinity "${STALLD_PID}")
 log "ℹ INFO: Default affinity: $default_affinity"
@@ -69,8 +69,8 @@ stop_stalld
 #=============================================================================
 test_section "Test 2: Single CPU affinity (-a 0)"
 
-start_stalld -f -v -l -t 5 -a 0
-sleep 2
+rm -f "${STALLD_LOG}"
+start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5 -a 0
 
 affinity=$(check_affinity "${STALLD_PID}")
 
@@ -84,8 +84,8 @@ stop_stalld
 test_section "Test 3: Multi-CPU affinity (-a 0,2)"
 
 if [ "$num_cpus" -ge 4 ]; then
-    start_stalld -f -v -l -t 5 -a 0,2
-    sleep 2
+    rm -f "${STALLD_LOG}"
+    start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5 -a 0,2
 
     affinity=$(check_affinity "${STALLD_PID}")
 
@@ -103,8 +103,8 @@ fi
 test_section "Test 4: CPU range affinity (-a 0-2)"
 
 if [ "$num_cpus" -ge 4 ]; then
-    start_stalld -f -v -l -t 5 -a 0-2
-    sleep 2
+    rm -f "${STALLD_LOG}"
+    start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5 -a 0-2
 
     affinity=$(check_affinity "${STALLD_PID}")
 
@@ -123,8 +123,8 @@ test_section "Test 5: Verify stalld threads run on specified CPU"
 
 if [ "$num_cpus" -ge 2 ]; then
     test_cpu=1
-    start_stalld -f -v -l -t 5 -a "$test_cpu"
-    sleep 2
+    rm -f "${STALLD_LOG}"
+    start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5 -a "$test_cpu"
 
     # Check affinity
     affinity=$(check_affinity "${STALLD_PID}")
@@ -174,8 +174,8 @@ assert_stalld_rejects "Invalid CPU affinity rejected with error" -f -v -l -t 5 -
 #=============================================================================
 test_section "Test 8: Verify affinity persists over time"
 
-start_stalld -f -v -l -t 5 -a 0
-sleep 2
+rm -f "${STALLD_LOG}"
+start_stalld_with_log "${STALLD_LOG}" -f -v -l -t 5 -a 0
 
 affinity_start=$(check_affinity "${STALLD_PID}")
 log "ℹ INFO: Initial affinity: $affinity_start"
-- 
2.54.0