Re: [PATCH v2 09/10] gpio: bd73800: Support ROHM BD73800 PMIC GPIOs

On 07/08/2026 23:29, Linus Walleij wrote:
> Hi Matti,
> 
> thanks for your patch!
> 
> On Tue, Aug 4, 2026 at 12:23 PM Matti Vaittinen
> <[email protected]> wrote:
> 
> 
>> +static int bd73800gpio_get(struct gpio_chip *chip, unsigned int offset)
>> +{
>> +       struct bd73800_gpio *data = gpiochip_get_data(chip);
>> +       struct bd73800_gpio_pin_cfg *pin = &data->pin[offset];
>> +       int ret, val;
>> +
>> +       /* Only pins configured as GPI via OTP can have their status read */
>> +       if (pin->state != BD73800_PIN_GPI) {
>> +               dev_dbg(data->dev, "pin %d (%x) not input. State %d\n", offset,
>> +                       pin->mask, pin->state);
>> +               return -EINVAL;
>> +       }
>> +
>> +       ret = regmap_read(data->regmap, BD73800_REG_INT_5_SRC, &val);
>> +       if (ret)
>> +               return ret;
>> +
>> +       return val & pin->mask;
>> +}
>> +
>> +static int bd73800gpo_set(struct gpio_chip *chip, unsigned int offset,
>> +                         int value)
>> +{
>> +       struct bd73800_gpio *data = gpiochip_get_data(chip);
>> +       struct bd73800_gpio_pin_cfg *pin = &data->pin[offset];
>> +
>> +       if (pin->state != BD73800_PIN_GPO) {
>> +               dev_dbg(data->dev, "pin %d (%d) not output. State %d\n",
>> +                       offset, pin->mask, pin->state);
>> +
>> +               return -EINVAL;
>> +       }
>> +
>> +       if (value)
>> +               return regmap_set_bits(data->regmap, BD73800_REG_GPO_OUT,
>> +                                      pin->mask);
>> +
>> +       return regmap_clear_bits(data->regmap, BD73800_REG_GPO_OUT, pin->mask);
>> +}
> 
> These can probably be handled by the latest version of gpio-regmap
> helpers (the version in linux-next).
> 
> We now support both input-only and output-only in gpio-regmap.

Allright, I'll take a look at the gpio-regmap again. Thanks for letting 
me know ...

> 
> Latest <linux/gpio/regmap.h>:
> 
>   * @fixed_direction_mask:
>   *                      (Optional) Bitmap representing the GPIO lines that
>   *                      make use of the @fixed_direction_output list to
>   *                      enforce direction of the GPIO. If this is NULL
>   *                      and @fixed_direction_output is defined, ALL GPIOs
>   *                      are assumed to be fixed direction (out or in).
>   * @fixed_direction_output:
>   *                      (Optional) Bitmap representing the fixed direction of
>   *                      the GPIO lines. Useful when there are GPIO lines with a
>   *                      fixed direction mixed together in the same register.
> 
> It seems you can set up the fixed_direction_output mask from OTP
> and just use the library, right?

... and thanks for going the extra mile and giving me this pointer. 
Helps a lot! :) I wish all reviewers had the time to give this specific 
suggestions - although, I understand this is not always feasible with 
the amount of reviews/tasks to handle.

Yours,
	-- Matti

-- 
Matti Vaittinen
Linux kernel developer at ROHM Semiconductors
Oulu Finland

~~ When things go utterly wrong vim users can always type :help! ~~