Re: [PATCH 07/10] scsi: ufs: Add NXP S32N79 UFS host controller driver

On 8/26/2026 6:49 PM, Frank Li wrote:
> On Wed, Aug 26, 2026 at 03:40:45PM +0200, Larisa Grigore wrote:
>>
>> Add support for the UFS host controller on the NXP S32N79 SoC, built on
>> the Synopsys DesignWare (DWC) UFS architecture, using the UFSHCD DWC and
>> UFSHCD platform glue.
>>
>> This controller requires S32N79-specific initialization prior to
>> UIC_LINKSTARTUP, including:
>>    - programming SCM.ONE_US_TICK and HC.HCLKDIV based on the core clock,
>>    - applying the vendor-defined M-PHY calibration sequence, and
>>    - performing post-link calibration steps needed for HS operation.
>>
>> The M-PHY boot mode is selected via the 'nxp,mphy-boot-mode' device tree
>> property. If the property is omitted, M-PHY initialization is assumed to
>> be handled by external firmware or by a simulation environment.
> 
> Is "simulation environment" productionable?

Thank you! I will remove any references to the simulation environment in v2.

> 
>>
>> Signed-off-by: Larisa Grigore <[email protected]>
>> ---
>>   drivers/ufs/host/Kconfig         |  12 +
>>   drivers/ufs/host/Makefile        |   1 +
>>   drivers/ufs/host/ufs-nxp-s32n7.c | 464 +++++++++++++++++++++++++++++++
>>   drivers/ufs/host/ufshcd-dwc.h    |   9 +-
>>   4 files changed, 484 insertions(+), 2 deletions(-)
>>   create mode 100644 drivers/ufs/host/ufs-nxp-s32n7.c
>>
>> diff --git a/drivers/ufs/host/Kconfig b/drivers/ufs/host/Kconfig
>> index ff170c0b6da0..e8ee7dd05f1a 100644
>> --- a/drivers/ufs/host/Kconfig
>> +++ b/drivers/ufs/host/Kconfig
>> @@ -168,3 +168,15 @@ config SCSI_UFS_AMD_VERSAL2
>>
>>            Select this if you have UFS controller on AMD Versal Gen 2 SoC.
>>            If unsure, say N.
>> +
>> +config SCSI_UFS_S32N7
>> +       tristate "NXP S32N7 platform driver"
>> +       depends on SCSI_UFSHCD_PLATFORM && (ARCH_S32 || COMPILE_TEST)
>> +       help
>> +         This selects the S32N7 specific additions on top of the UFSHCD DWC
>> +         and UFSHCD platform driver. UFS host on S32N79 needs some vendor
>> +         specific configurations like PHY and vendor specific register accesses
>> +         before accessing the hardware.
>> +
>> +         Select this if you have UFS controller on an S32N7 based board.
>> +         If unsure, say N.
>> diff --git a/drivers/ufs/host/Makefile b/drivers/ufs/host/Makefile
>> index 65d8bb23ab7b..0381750a35d3 100644
>> --- a/drivers/ufs/host/Makefile
>> +++ b/drivers/ufs/host/Makefile
>> @@ -2,6 +2,7 @@
>>
>>   obj-$(CONFIG_SCSI_UFS_DWC_TC_PCI) += tc-dwc-g210-pci.o ufshcd-dwc.o tc-dwc-g210.o
>>   obj-$(CONFIG_SCSI_UFS_DWC_TC_PLATFORM) += tc-dwc-g210-pltfrm.o ufshcd-dwc.o tc-dwc-g210.o
>> +obj-$(CONFIG_SCSI_UFS_S32N7) += ufs-nxp-s32n7.o ufshcd-dwc.o
> 
> It is not related with your patch, but multi ufshcd-dwc.o may link many
> times if other ufs host driver also build, modern link can remove duplicate
> symbal, but not sure what happen if one build as module, one buildin.
> 
>>   obj-$(CONFIG_SCSI_UFS_CDNS_PLATFORM) += cdns-pltfrm.o
>>   obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
>>   obj-$(CONFIG_SCSI_UFS_EXYNOS) += ufs-exynos.o
>> diff --git a/drivers/ufs/host/ufs-nxp-s32n7.c b/drivers/ufs/host/ufs-nxp-s32n7.c
>> new file mode 100644
>> index 000000000000..8a125105536b
>> --- /dev/null
>> +++ b/drivers/ufs/host/ufs-nxp-s32n7.c
>> @@ -0,0 +1,464 @@
>> +// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
>> +/*
>> + * Copyright 2026 NXP
>> + *
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +
>> +#include "ufshcd-pltfrm.h"
>> +#include "ufshcd-dwc.h"
>> +#include "ufshci-dwc.h"
>> +
>> +/* SCM Register Offsets. */
>> +#define SCM_ONE_US_TICK                        0x2CU
>> +#define SCM_STATUS                     0x30
>> +
>> +/* SCM_ONE_US_TICK Register. */
>> +#define SCM_ONE_US_TICK_MASK           GENMASK(8, 0)
>> +
>> +/* SCM_MPHY_RAM_CONFIG_STATUS Register Fields. */
>> +#define SCM_STATUS_PHY_RESET_MASK              BIT(0)
>> +#define SCM_STATUS_SRAM_BYPASS_MASK            BIT(1)
>> +#define SCM_STATUS_SRAM_INIT_DONE_MASK         BIT(16)
>> +
>> +#define SCM_STATUS_PHY_RESET(val)              \
>> +       FIELD_PREP(SCM_STATUS_PHY_RESET_MASK, val)
>> +
>> +#define SCM_STATUS_SRAM_BYPASS(val)            \
>> +       FIELD_PREP(SCM_STATUS_SRAM_BYPASS_MASK, val)
>> +
>> +/* Timeout values. */
>> +#define CFG_MPHY_INIT_TIMEOUT_VALUE_US 3000000
>> +
>> +/* Clock validation limits. */
>> +#define MAX_VALID_ONE_US_TICK          SCM_ONE_US_TICK_MASK
>> +
>> +/* CPort definitions */
>> +#define CPORT_0                                0
>> +
>> +/* Hibern8 state poll timeout. */
>> +#define HBRN8_POLL_TOUT_MS      1000
> 
> Does this value is spec defined or just engineering choose?

This is engineering choose. I will update the commit message. Thanks!

>> +
>> +/**
>> + * enum mphy_boot_mode - MPHY boot mode options
>> + * @MPHY_BOOT_NONE: Skip MPHY initialization
>> + * @MPHY_BOOT_ROM: Running MPHY from internal FW ROM
>> + */
>> +enum mphy_boot_mode {
>> +       MPHY_BOOT_NONE = 0,
>> +       MPHY_BOOT_ROM = 1,
>> +};
>> +
>> +/**
>> + * struct s32n_ufs - S32N7 UFS host controller data
>> + * @hba: UFS host controller instance
>> + * @reg_scm: SCM register base address
>> + * @core_clk: core reference clock used to derive ONE_US_TICK/HCLKDIV
>> + * @mphy_boot_mode: MPHY boot mode configuration
>> + */
>> +struct s32n_ufs {
>> +       struct ufs_hba *hba;
>> +       void __iomem *reg_scm;
>> +       struct clk *core_clk;
>> +       enum mphy_boot_mode mphy_boot_mode;
>> +};
>> +
>> +/**
>> + * struct phy_reg_cfg - PHY register configuration entry
>> + * @reg: Register offset/address
>> + * @val: Value to write
>> + */
>> +struct phy_reg_cfg {
>> +       u32 reg;
>> +       u32 val;
>> +};
>> +
>> +/**
>> + * ufs_s32n_phy_write_sequence - Write a sequence of PHY registers
>> + * @hba: UFS host controller instance
>> + * @cfg: Array of register configurations
>> + * @count: Number of entries in the array
>> + *
>> + * Return: 0 on success, error code on failure
>> + */
>> +static int ufs_s32n_phy_write_sequence(struct ufs_hba *hba,
>> +                                      const struct phy_reg_cfg *cfg,
>> +                                      size_t count)
>> +{
>> +       int ret;
>> +       size_t i;
>> +
>> +       for (i = 0; i < count; i++) {
>> +               ret = ufshcd_dwc_phy_reg_write(hba, cfg[i].reg, cfg[i].val);
>> +               if (ret) {
>> +                       dev_err(hba->dev,
>> +                               "Failed to write PHY reg 0x%x = 0x%x (step %zu)\n",
>> +                               cfg[i].reg, cfg[i].val, i);
>> +                       return ret;
>> +               }
>> +       }
>> +
>> +       return 0;
>> +}
>> +
>> +static unsigned long ufs_s32n_calculate_us_tick(unsigned long clk_rate)
>> +{
>> +       return clk_rate / USEC_PER_SEC;
>> +}
>> +
>> +static int ufs_s32n_configure_clocks(struct ufs_hba *hba)
>> +{
>> +       struct s32n_ufs *ufs = ufshcd_get_variant(hba);
>> +       struct device *dev = hba->dev;
>> +       unsigned long clk_rate = 0;
>> +       unsigned long one_us_tick;
>> +
>> +       if (!ufs->core_clk) {
> 
> suppose return failure at probe if no core_clk, needn't check here

You are correct. Thank you!

> 
>> +               dev_err(dev, "Invalid core_clk.\n");
>> +               return -EINVAL;
>> +       }
>> +
>> +       clk_rate = clk_get_rate(ufs->core_clk);
>> +       if (!clk_rate) {
>> +               dev_err(dev, "Failed to get valid clock rate.\n");
>> +               return -EINVAL;
>> +       }
>> +
>> +       one_us_tick = ufs_s32n_calculate_us_tick(clk_rate);
>> +       if (one_us_tick == 0 || one_us_tick > MAX_VALID_ONE_US_TICK) {
>> +               dev_err(dev, "Invalid one_us_tick value: %lu (clk_rate: %lu Hz).\n",
>> +                       one_us_tick, clk_rate);
>> +               return -EINVAL;
>> +       }
>> +
>> +       dev_dbg(dev, "Core clock rate: %lu Hz, one_us_tick = %lu.\n",
>> +                clk_rate, one_us_tick);
>> +
>> +       /*
>> +        * Configure the micro-second tick rate generator based on core
>> +        * clock rate.
>> +        */
>> +       writel(one_us_tick, ufs->reg_scm + SCM_ONE_US_TICK);
>> +       ufshcd_dwc_program_clk_div(hba, one_us_tick);
>> +
>> +       return 0;
>> +}
>> +
>> +static int ufs_s32n_phy_initial_calib(struct ufs_hba *hba)
>> +{
>> +       static const struct phy_reg_cfg initial_calib[] = {
>> +               { FAST_FLAGS(0), 0x6 },
>> +               { FAST_FLAGS(1), 0x6 },
>> +               { RX_DAC_CTRL_OVRD(0), 0x1 },
>> +               { RX_DAC_CTRL_OVRD(1), 0x1 },
>> +               { RX_DAC_CTRL(0), 0x8E },
>> +               { RX_DAC_CTRL(1), 0x91 },
>> +               { RX_DAC_CTRL_SEL(0), 0x1 },
>> +               { RX_DAC_CTRL_SEL(1), 0x1 },
>> +               { RX_DAC_CTRL_EN(0), 0x1 },
>> +               { RX_DAC_CTRL_EN(1), 0x1 },
>> +               { RX_DAC_CTRL_OVRD(0), 0x0 },
>> +               { RX_DAC_CTRL_OVRD(1), 0x0 },
>> +               { RX_DAC_CTRL_OVRD(0), 0x1 },
>> +               { RX_DAC_CTRL_OVRD(1), 0x1 },
>> +               { RX_DAC_CTRL(0), 0x71 },
>> +               { RX_DAC_CTRL(1), 0x7F },
>> +               { RX_DAC_CTRL_SEL(0), 0x2 },
>> +               { RX_DAC_CTRL_SEL(1), 0x2 },
>> +               { RX_DAC_CTRL_EN(0), 0x1 },
>> +               { RX_DAC_CTRL_EN(1), 0x1 },
>> +               { RX_DAC_CTRL_OVRD(0), 0x0 },
>> +               { RX_DAC_CTRL_OVRD(1), 0x0 },
>> +               { FW_CALIB_CCFG(0), 0x100 },
>> +               { FW_CALIB_CCFG(1), 0x100 },
>> +       };
> 
> Can you put this data to platform data in case difference data for differe
> soc in future?

Thanks for the sugestion! I will add both initial_calib and post_calib.

> 
>> +       int ret;
>> +
>> +       /* Clock Control */
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CBREFCLKCTRL2, 0), 0x80);
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(VS_MPHYCFGUPDT, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* Initial calibration sequence */
>> +       return ufs_s32n_phy_write_sequence(hba, initial_calib,
>> +                                          ARRAY_SIZE(initial_calib));
>> +}
>> +
>> +static int ufs_s32n_link_startup_pre_change(struct ufs_hba *hba)
>> +{
>> +       struct s32n_ufs *ufs = ufshcd_get_variant(hba);
>> +       struct device *dev = hba->dev;
>> +       int ret;
>> +       u32 reg;
>> +
>> +       /*
>> +        * There are two supported MPHY boot options implemented:
>> +        * - Running MPHY from internal FW ROM:
>> +        *  MPHY_RAM_CONFIG_STATUS.SRAM_BYPASS = 1
>> +        *  MPHY_RAM_CONFIG_STATUS.SRAM_EXT_LD_DONE = 0
>> +        * - Skip M-PHY initialization when it is handled externally.
>> +        */
>> +       if (ufs->mphy_boot_mode == MPHY_BOOT_NONE) {
>> +               dev_dbg(dev, "Skipping UFS MPHY init.\n");
>> +               return 0;
>> +       }
>> +
>> +       ret = ufs_s32n_configure_clocks(hba);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* Reset SCM.MPHY_RAM_CONFIG_STATUS to default value; keep MPHY in reset. */
>> +       writel(SCM_STATUS_PHY_RESET(1), ufs->reg_scm + SCM_STATUS);
>> +       if (ufs->mphy_boot_mode == MPHY_BOOT_ROM) {
>> +               /* ROM Mode. */
>> +               writel(SCM_STATUS_PHY_RESET(1) | SCM_STATUS_SRAM_BYPASS(1),
>> +                      ufs->reg_scm + SCM_STATUS);
>> +       }
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CBCRCTRL, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(VS_MPHYCFGUPDT, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* Release PHY_RESET. */
>> +       writel(readl(ufs->reg_scm + SCM_STATUS) & ~SCM_STATUS_PHY_RESET_MASK,
>> +              ufs->reg_scm + SCM_STATUS);
>> +
>> +       /* Wait until SRAM_INIT_DONE = 1. */
>> +       ret = readl_poll_timeout(ufs->reg_scm + SCM_STATUS, reg,
>> +                       reg & SCM_STATUS_SRAM_INIT_DONE_MASK,
>> +                       1000, CFG_MPHY_INIT_TIMEOUT_VALUE_US);
>> +       if (ret) {
>> +               dev_err(dev, "UFS MPHY init not done!\n");
>> +               return ret;
>> +       }
>> +
>> +       /* Start of initial calibration */
>> +       ret = ufs_s32n_phy_initial_calib(hba);
>> +       if (ret) {
>> +               dev_err(dev, "UFS MPHY initial calibration failed!\n");
>> +               return ret;
>> +       }
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(VS_MPHYDISABLE, 0), 0x0);
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(VS_MPHYCFGUPDT, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* Set Local DeviceID. */
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(N_DEVICEID, 0), 0x0);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* End of Gear1 settings */
>> +
>> +       return ufshcd_check_hibern8(hba, hba->lanes_per_direction,
>> +                                   HBRN8_POLL_TOUT_MS);
>> +}
>> +
>> +static int ufs_s32n_link_startup_post_change(struct ufs_hba *hba)
>> +{
>> +       static const struct ufshcd_dme_attr_val cport_setup[] = {
>> +               { UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, CPORT_0),
>> +                               CPORT_IDLE, DME_LOCAL },
>> +               { UIC_ARG_MIB_SEL(T_CPORTFLAGS, CPORT_0),
>> +                               CPORT_DEF_FLAGS, DME_LOCAL },
>> +               { UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, CPORT_0),
>> +                               CPORT_CONNECTED, DME_LOCAL },
>> +       };
>> +       static const struct phy_reg_cfg post_calib[] = {
>> +               { RX_OVRD_IN_1(0), 0xc },
>> +               { RX_OVRD_IN_1(1), 0xc },
>> +               { RX_OVRD_IN_1(0), 0x8 },
>> +               { RX_OVRD_IN_1(1), 0x8 },
>> +               { RX_OVRD_IN_1(0), 0x0 },
>> +               { RX_OVRD_IN_1(1), 0x0 },
>> +       };
>> +       struct s32n_ufs *ufs = ufshcd_get_variant(hba);
>> +       unsigned int data = 0;
>> +       int ret;
>> +
>> +       if (ufs->mphy_boot_mode == MPHY_BOOT_NONE)
>> +               return 0;
>> +
>> +       /* Set Connection State to IDLE (it allows CPort Attributes to be set). */
>> +       ret = ufshcd_dwc_dme_set_attrs(hba, cport_setup, ARRAY_SIZE(cport_setup));
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = ufshcd_dme_get(hba, UIC_ARG_MIB_SEL(T_CONNECTIONSTATE, CPORT_0), &data);
>> +       if (ret)
>> +               return ret;
>> +
>> +       if (data != CPORT_CONNECTED)
>> +               return -EIO;
>> +
>> +       /* Post Link Startup Calibration sequence */
>> +       ret = ufs_s32n_phy_write_sequence(hba, post_calib,
>> +                                          ARRAY_SIZE(post_calib));
>> +       if (ret)
>> +               return ret;
>> +
>> +       /*
>> +        * Performing MPHY configuration for rate change:
>> +        * CB rate selection: 0 - rate A, 1 - rate B;
>> +        */
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(CBRATESEL, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       ret = ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(VS_MPHYCFGUPDT, 0), 0x1);
>> +       if (ret)
>> +               return ret;
>> +
>> +       /* End of Gear4 calibration */
>> +       return 0;
>> +}
>> +
>> +static int ufs_s32n_link_startup_notify(struct ufs_hba *hba,
>> +                            enum ufs_notify_change_status status)
>> +{
>> +       int err;
>> +
>> +       if (status == PRE_CHANGE) {
>> +               err = ufs_s32n_link_startup_pre_change(hba);
>> +               if (err) {
>> +                       dev_err(hba->dev, "MPHY setup failed (%d).\n", err);
>> +                       return err;
>> +               }
>> +               return 0;
>> +       }
>> +
>> +       /* POST_CHANGE */
>> +       err = ufshcd_dwc_link_is_up(hba);
>> +       if (err) {
>> +               dev_err(hba->dev, "Link is not up.\n");
>> +               return err;
>> +       }
>> +
>> +       err = ufs_s32n_link_startup_post_change(hba);
>> +       if (err)
>> +               dev_err(hba->dev, "Connection setup failed (%d).\n", err);
>> +
>> +       return err;
>> +}
>> +
>> +static int ufs_s32n_init(struct ufs_hba *hba)
>> +{
>> +       struct device *dev = hba->dev;
>> +       struct platform_device *pdev = to_platform_device(dev);
>> +       struct device_node *np = dev->of_node;
>> +       const char *mphy_boot_mode;
>> +       struct s32n_ufs *ufs;
>> +       int ret;
>> +
>> +       ufs = devm_kzalloc(dev, sizeof(*ufs), GFP_KERNEL);
>> +       if (!ufs)
>> +               return -ENOMEM;
>> +
>> +       ufs->hba = hba;
>> +       ufs->mphy_boot_mode = MPHY_BOOT_NONE;
>> +
>> +       hba->quirks |= UFSHCD_QUIRK_BROKEN_AUTO_HIBERN8;
>> +       hba->quirks |= UFSHCD_QUIRK_PERFORM_LINK_STARTUP_ONCE;
>> +       hba->spm_lvl = UFS_PM_LVL_5;
>> +
>> +       ret = of_property_read_string(np, "nxp,mphy-boot-mode", &mphy_boot_mode);
>> +       if (ret || !mphy_boot_mode) {
>> +               dev_dbg(dev,
>> +                       "nxp,mphy-boot-mode property not found. UFS MPHY init will be skipped.\n");
>> +               goto init_out;
>> +       }
>> +
>> +       if (!strcmp(mphy_boot_mode, "rom")) {
>> +               ufs->mphy_boot_mode = MPHY_BOOT_ROM;
>> +       } else {
>> +               return dev_err_probe(dev, -EINVAL,
>> +                                    "Unrecognized nxp,mphy-boot-mode property. UFS MPHY init will be skipped.\n");
>> +       }
>> +
>> +       ufs->reg_scm = devm_platform_ioremap_resource_byname(pdev, "scm");
>> +       if (IS_ERR(ufs->reg_scm))
>> +               return dev_err_probe(dev, PTR_ERR(ufs->reg_scm),
>> +                                    "ioremap failed for SCM registers.\n");
>> +
>> +       ufs->core_clk = devm_clk_get(dev, "core_clk");
>> +       if (IS_ERR(ufs->core_clk))
>> +               return dev_err_probe(dev, PTR_ERR(ufs->core_clk),
>> +                                    "Failed to get core clock.\n");
>> +
>> +init_out:
>> +       ufshcd_set_variant(hba, ufs);
>> +
>> +       return 0;
>> +}
>> +
>> +static const struct ufs_hba_variant_ops ufs_hba_s32n79_vops = {
>> +       .name = "s32n79",
>> +       .init = ufs_s32n_init,
>> +       .link_startup_notify = ufs_s32n_link_startup_notify,
>> +};
>> +
>> +static const struct of_device_id ufs_s32n7_match[] = {
>> +       {
>> +               .compatible = "nxp,s32n79-ufshc",
>> +               .data = &ufs_hba_s32n79_vops,
>> +       },
>> +       { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, ufs_s32n7_match);
>> +
>> +static int ufs_s32n7_probe(struct platform_device *pdev)
>> +{
>> +       const struct ufs_hba_variant_ops *vops;
>> +
>> +       vops = device_get_match_data(&pdev->dev);
>> +       if (!vops)
>> +               return -ENODEV;
>> +
>> +       return ufshcd_pltfrm_init(pdev, vops);
>> +}
>> +
>> +static void ufs_s32n7_remove(struct platform_device *pdev)
>> +{
>> +       ufshcd_pltfrm_remove(pdev);
>> +}
>> +
>> +static const struct dev_pm_ops ufs_s32n7_pm_ops = {
>> +       SET_SYSTEM_SLEEP_PM_OPS(ufshcd_system_suspend, ufshcd_system_resume)
>> +       SET_RUNTIME_PM_OPS(ufshcd_runtime_suspend, ufshcd_runtime_resume, NULL)
> 
> Use  SYSTEM_SLEEP_PM_OPS()
> 
>> +       .prepare        = ufshcd_suspend_prepare,
>> +       .complete       = ufshcd_resume_complete,
>> +};
>> +
>> +static struct platform_driver ufs_s32n7_driver = {
>> +       .probe = ufs_s32n7_probe,
>> +       .remove = ufs_s32n7_remove,
>> +       .driver = {
>> +               .name   = "ufs-s32n7",
>> +               .pm     = &ufs_s32n7_pm_ops,
> 
> pm_ptr(&ufs_s32n7_pm_ops)
> 
> Frank

I will address these comments in v2.

Best regards,
Larisa

> 
>> +               .of_match_table = ufs_s32n7_match,
>> +       },
>> +};
>> +
>> +module_platform_driver(ufs_s32n7_driver);
>> +
>> +MODULE_AUTHOR("Larisa Grigore <[email protected]>");
>> +MODULE_DESCRIPTION("NXP S32N7 UFS Host Controller platform driver");
>> +MODULE_LICENSE("Dual BSD/GPL");
>> diff --git a/drivers/ufs/host/ufshcd-dwc.h b/drivers/ufs/host/ufshcd-dwc.h
>> index 53b523ef59df..747383cfb839 100644
>> --- a/drivers/ufs/host/ufshcd-dwc.h
>> +++ b/drivers/ufs/host/ufshcd-dwc.h
>> @@ -13,8 +13,7 @@
>>   #include <ufs/ufshcd.h>
>>
>>   /* RMMI Attributes */
>> -#define CBREFCLKCTRL2          0x8132
>> -#define CBCRCTRL               0x811F
>> +#define RXSQCONTROL            0x8009
>>   #define CBC10DIRECTCONF2       0x810E
>>   #define CBRATESEL              0x8114
>>   #define CBCREGADDRLSB          0x8116
>> @@ -24,10 +23,16 @@
>>   #define CBCREGRDLSB            0x811A
>>   #define CBCREGRDMSB            0x811B
>>   #define CBCREGRDWRSEL          0x811C
>> +#define CBCRCTRL               0x811F
>> +#define CBREFCLKCTRL2          0x8132
>>
>>   #define CBREFREFCLK_GATE_OVR_EN                BIT(7)
>>
>>   /* M-PHY registers */
>> +#define RX_DAC_CTRL(n)         (0x10AF + ((n) * 0x100))
>> +#define RX_DAC_CTRL_OVRD(n)    (0x10B0 + ((n) * 0x100))
>> +#define RX_DAC_CTRL_SEL(n)     (0x10B1 + ((n) * 0x100))
>> +#define RX_DAC_CTRL_EN(n)      (0x10B8 + ((n) * 0x100))
>>   #define RX_OVRD_IN_1(n)                (0x3006 + ((n) * 0x100))
>>   #define RX_PCS_OUT(n)          (0x300F + ((n) * 0x100))
>>   #define FAST_FLAGS(n)          (0x401C + ((n) * 0x100))
>> --
>> 2.43.0
>>
>>