[RESEND PATCH] sh: ecovec24: use static device properties to describe the touchscreen

Convert the board to use static device properties instead of platform
data to describe the touchscreen, so that support for platform data can
be removed from tsc2007 driver (ecovec24 is the last board using this
mechanism of describing tsc2007).

Device properties do not allow custom board methods, so the method for
getting "pen down" state was removed (the driver is capable of working
without it). If this functionality is needed proper pin control/gpio
support needs to be implemented so that the same pin can serve as an
input GPIO and an interrupt.

Signed-off-by: Dmitry Torokhov <[email protected]>
---

This is a resend of the patch I sent in August of 2024. My fault of not
noticing reply from Adrian inquiring about potential negative impact
from not having GPIO-based "pen down" detection. I believe this is fine,
the "pen down" is an optional feature and the driver can detect the
touches even when it is not specified. Additionally, this is an
evaluation board, so user impact should be negligible.

However the bigger question is whether ecovec24 board still relevant.
According to my research it has the following regressions currently
unfixed:

5716fb9bd9c6 ("mmc: spi: Convert to use GPIO descriptors")
  - MMC SPI device naming broken (broke SD fallback mode)

9fda6693335c ("spi: sh-msiof: Convert to use GPIO descriptors")
  - SPI CS polarity inverted (broke initialization on the MSIOF0 SPI bus)

c2f9b05fd5c1 ("media: arch: sh: ecovec: Use new renesas-ceu camera driver")
  - Camera array sentinel missing (causes out-of-bounds reads and
    potentially kernel panics)
  - Camera standby polarity inverted (enadvertently keeps cameras
    permanently powered off)
  - Camera disabled iby default (board defconfig points to a deleted
    driver)

They are ~6 years old, so I wonder: do people actually *actively* use
this board with modern kernels? Should it simply be removed?

Thanks!

 arch/sh/boards/mach-ecovec24/setup.c | 38 ++++++++--------------------
 1 file changed, 11 insertions(+), 27 deletions(-)

diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index a641e26f8fdf..110a77f903b5 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -26,6 +26,7 @@
 #include <linux/platform_data/tmio.h>
 #include <linux/platform_data/tsc2007.h>
 #include <linux/platform_device.h>
+#include <linux/property.h>
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/sh_eth.h>
@@ -589,39 +590,21 @@ static struct platform_device keysc_device = {
 /* TouchScreen */
 #define IRQ0 evt2irq(0x600)
 
-static int ts_get_pendown_state(struct device *dev)
-{
-	int val = 0;
-	gpio_free(GPIO_FN_INTC_IRQ0);
-	gpio_request(GPIO_PTZ0, NULL);
-	gpio_direction_input(GPIO_PTZ0);
-
-	val = gpio_get_value(GPIO_PTZ0);
-
-	gpio_free(GPIO_PTZ0);
-	gpio_request(GPIO_FN_INTC_IRQ0, NULL);
-
-	return val ? 0 : 1;
-}
-
-static int ts_init(void)
-{
-	gpio_request(GPIO_FN_INTC_IRQ0, NULL);
-	return 0;
-}
+static const struct property_entry tsc2007_properties[] = {
+	PROPERTY_ENTRY_U32("ti,x-plate-ohms", 180),
+	{ }
+};
 
-static struct tsc2007_platform_data tsc2007_info = {
-	.model			= 2007,
-	.x_plate_ohms		= 180,
-	.get_pendown_state	= ts_get_pendown_state,
-	.init_platform_hw	= ts_init,
+static const struct software_node tsc2007_swnode = {
+	.name = "tsc2007",
+	.properties = tsc2007_properties,
 };
 
 static struct i2c_board_info ts_i2c_clients = {
 	I2C_BOARD_INFO("tsc2007", 0x48),
 	.type		= "tsc2007",
-	.platform_data	= &tsc2007_info,
 	.irq		= IRQ0,
+	.swnode		= &tsc2007_swnode,
 };
 
 static struct regulator_consumer_supply cn12_power_consumers[] =
@@ -1242,8 +1225,9 @@ static int __init arch_setup(void)
 		gpio_direction_output(GPIO_PTF4, 1);
 
 		/* enable TouchScreen */
-		i2c_register_board_info(0, &ts_i2c_clients, 1);
+		gpio_request(GPIO_FN_INTC_IRQ0, NULL);
 		irq_set_irq_type(IRQ0, IRQ_TYPE_LEVEL_LOW);
+		i2c_register_board_info(0, &ts_i2c_clients, 1);
 	}
 
 	/* enable CEU0 */
-- 
2.55.0.795.g602f6c329a-goog


-- 
Dmitry