An unexpected IO-APIC was found.

Inspecting /boot/System.map-2.4.21-144-smp4G
Loaded 21746 symbols from /boot/System.map-2.4.21-144-smp4G.
Symbols match kernel version 2.4.21.
Loaded 546 symbols from 15 modules.
klogd 1.4.1, log source = ksyslog started.
<4>Linux version 2.4.21-144-smp4G ([email protected]) (gcc version 3.3.1 (SuSE Linux)) #1 SMP Fri Nov 14 00:07:01 UTC 2003
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
<4> BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
<4> BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
<4> BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
<4> BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
<5>501MB vmalloc/ioremap area available.
<5>0MB HIGHMEM available.
<5>511MB LOWMEM available.
<7>ACPI: have wakeup address 0xc0002000
<4>found SMP MP-table at 000ff780
<4>hm, page 000ff000 reserved twice.
<4>hm, page 00100000 reserved twice.
<4>hm, page 000f1000 reserved twice.
<4>hm, page 000f2000 reserved twice.
<4>On node 0 totalpages: 130864
<4>zone(0): 4096 pages.
<4>zone(1): 126768 pages.
<4>zone(2): 0 pages.
<6>ACPI: RSDP (v000 ACPIAM                     ) @ 0x000f9fb0
<6>ACPI: RSDT (v001 A M I  OEMRSDT  01024.00802) @ 0x1ff30000
<6>ACPI: FADT (v002 A M I  OEMFACP  01024.00802) @ 0x1ff30200
<6>ACPI: MADT (v001 A M I  OEMAPIC  01024.00802) @ 0x1ff30390
<6>ACPI: OEMB (v001 A M I  OEMBIOS  01024.00802) @ 0x1ff40040
<6>ACPI: DSDT (v001  P4C81 P4C81053 00000.00083) @ 0x00000000
<6>ACPI: Local APIC address 0xfee00000
<6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
<4>Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
<6>ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
<6>ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
<6>IOAPIC[0]: Assigned apic_id 2
<4>IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, IRQ 0-23
<6>ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
<6>ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
<6>Using ACPI (MADT) for SMP configuration information
<4>Building zonelist for node : 0
<4>Kernel command line: ro root=LABEL=suse-root hdc=ide-scsi
<6>ide_setup: hdc=ide-scsi
<6>Initializing CPU#0
<4>Detected 3006.861 MHz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 6003.09 BogoMIPS
<6>Memory: 507844k/523456k available (1867k kernel code, 11008k reserved, 638k data, 188k init, 0k highmem)
<6>Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
<6>Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU:             Common caps: bfebfbff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch ([email protected])
<4>mtrr: detected mtrr type: Intel
<6>CPU: Trace cache: 12K uops, L1 D cache: 8K
<6>CPU: L2 cache: 512K
<6>CPU: Physical Processor ID: 0
<6>Intel machine check reporting enabled on CPU#0.
<7>CPU:     After generic, caps: bfebfbff 00000000 00000000 00000000
<7>CPU:             Common caps: bfebfbff 00000000 00000000 00000000
<4>CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
<4>per-CPU timeslice cutoff: 1463.08 usecs.
<4>task migration cache decay timeout: 10 msecs.
<4>enabled ExtINT on CPU#0
<4>ESR value before enabling vector: 00000000
<4>ESR value after enabling vector: 00000000
<3>Error: only one processor found.
<4>WARNING: No sibling found for CPU 0.
<4>ENABLING IO-APIC IRQs
<7>init IO_APIC IRQs
<7> IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
<6>..TIMER: vector=0x31 pin1=2 pin2=0
<7>number of MP IRQ sources: 16.
<7>number of IO-APIC #2 registers: 24.
<6>testing the IO APIC.......................
<4>
<7>IO APIC #2......
<7>.... register #00: 02000000
<7>.......    : physical APIC id: 02
<7>.......    : Delivery Type: 0
<7>.......    : LTS          : 0
<7>.... register #01: 00178020
<7>.......     : max redirection entries: 0017
<7>.......     : PRQ implemented: 1
<7>.......     : IO APIC version: 0020
<7>.... register #02: 00178020
<7>.......     : arbitration: 00
<4>An unexpected IO-APIC was found. If this kernel release is less than
<4>three months old please report this to [email protected]
<7>.... IRQ redirection table:
<7> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
<7> 00 000 00  1    0    0   0   0    0    0    00
<7> 01 001 01  0    0    0   0   0    1    1    39
<7> 02 001 01  0    0    0   0   0    1    1    31
<7> 03 001 01  0    0    0   0   0    1    1    41
<7> 04 001 01  0    0    0   0   0    1    1    49
<7> 05 001 01  0    0    0   0   0    1    1    51
<7> 06 001 01  0    0    0   0   0    1    1    59
<7> 07 001 01  0    0    0   0   0    1    1    61
<7> 08 001 01  0    0    0   0   0    1    1    69
<7> 09 001 01  1    1    0   0   0    1    1    71
<7> 0a 001 01  0    0    0   0   0    1    1    79
<7> 0b 001 01  0    0    0   0   0    1    1    81
<7> 0c 001 01  0    0    0   0   0    1    1    89
<7> 0d 001 01  0    0    0   0   0    1    1    91
<7> 0e 001 01  0    0    0   0   0    1    1    99
<7> 0f 001 01  0    0    0   0   0    1    1    A1
<7> 10 000 00  1    0    0   0   0    0    0    00
<7> 11 000 00  1    0    0   0   0    0    0    00
<7> 12 000 00  1    0    0   0   0    0    0    00
<7> 13 000 00  1    0    0   0   0    0    0    00
<7> 14 000 00  1    0    0   0   0    0    0    00
<7> 15 06C 0C  1    0    0   0   0    0    2    FF
<7> 16 000 00  1    0    0   0   0    0    0    00
<7> 17 000 00  1    0    0   0   0    0    0    00
<7>IRQ to pin mappings:
<7>IRQ0 -> 0:2
<7>IRQ1 -> 0:1
<7>IRQ3 -> 0:3
<7>IRQ4 -> 0:4
<7>IRQ5 -> 0:5
<7>IRQ6 -> 0:6
<7>IRQ7 -> 0:7
<7>IRQ8 -> 0:8
<7>IRQ9 -> 0:9
<7>IRQ10 -> 0:10
<7>IRQ11 -> 0:11
<7>IRQ12 -> 0:12
<7>IRQ13 -> 0:13
<7>IRQ14 -> 0:14
<7>IRQ15 -> 0:15
<6>.................................... done.
<4>Using local APIC timer interrupts.
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 3006.9854 MHz.
<4>..... host bus clock speed is 200.4656 MHz.
<4>cpu: 0, clocks: 2004656, slice: 1002328
<4>CPU0<T0:2004656,T1:1002320,D:8,S:1002328,C:2004656>
<4>migration_task 0 on cpu=0
<6>ACPI: Subsystem revision 20030619
<6>PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
<6>PCI: Using configuration type 1
<6>Looking for DSDT in initrd ... not found!
<7>IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9) Mode:1 Active:0
<6>ACPI: Interpreter enabled
<6>ACPI: Using IOAPIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S1 S3 S4 S5)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
<4>Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
<6>PCI: Probing PCI hardware
<7>IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18) Mode:1 Active:1
<7>00:00:1f[A] -> 2-18 -> IRQ 18
<7>IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17) Mode:1 Active:1
<7>00:00:1f[B] -> 2-17 -> IRQ 17
<7>IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16) Mode:1 Active:1
<7>00:00:1d[A] -> 2-16 -> IRQ 16
<7>IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19) Mode:1 Active:1
<7>00:00:1d[B] -> 2-19 -> IRQ 19
<7>Pin 2-18 already programmed
<7>IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23) Mode:1 Active:1
<7>00:00:1d[D] -> 2-23 -> IRQ 23
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-16 already programmed
<7>Pin 2-17 already programmed
<7>Pin 2-18 already programmed
<7>Pin 2-19 already programmed
<7>IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20) Mode:1 Active:1
<7>00:02:08[A] -> 2-20 -> IRQ 20
<7>IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd9 -> IRQ 21) Mode:1 Active:1
<7>00:02:09[A] -> 2-21 -> IRQ 21
<7>IOAPIC[0]: Set PCI routing entry (2-22 -> 0xe1 -> IRQ 22) Mode:1 Active:1
<7>00:02:09[B] -> 2-22 -> IRQ 22
<7>Pin 2-23 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-22 already programmed
<7>Pin 2-23 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-21 already programmed
<7>Pin 2-23 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-21 already programmed
<7>Pin 2-22 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-21 already programmed
<7>Pin 2-22 already programmed
<7>Pin 2-23 already programmed
<7>Pin 2-21 already programmed
<7>Pin 2-22 already programmed
<7>Pin 2-23 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-20 already programmed
<7>Pin 2-23 already programmed
<7>Pin 2-22 already programmed
<6>PCI: Using ACPI for IRQ routing
<6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<6>apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
<5>apm: overridden by ACPI.
<4>Starting kswapd
<4>bigpage subsystem: allocated 0 bigpages (=0MB).
<4>kinoded started
<5>VFS: Disk quotas vdquot_6.5.1
<5>aio_setup: num_physpages = 32716
<5>aio_setup: sizeof(struct page) = 48
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>Real Time Clock Driver v1.10e
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
<6>loop: loaded (max 16 devices)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>PIIX-4: IDE controller at PCI slot 00:1f.1
<4>PCI: Enabling device 00:1f.1 (0005 -> 0007)
<6>PIIX-4: chipset revision 2
<6>PIIX-4: not 100%% native mode: will probe irqs later
<6>    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
<6>    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
<4>hda: Maxtor 6Y120L0, ATA DISK drive
<4>hdb: Maxtor 6Y120L0, ATA DISK drive
<4>blk: queue c046ad40, I/O limit 4095Mb (mask 0xffffffff)
<4>blk: queue c046aea4, I/O limit 4095Mb (mask 0xffffffff)
<4>hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: attached ide-disk driver.
<4>hda: host protected area => 1
<6>hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(100)
<4>hdb: attached ide-disk driver.
<4>hdb: host protected area => 1
<6>hdb: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(100)
<6>ide-floppy driver 0.99.newide
<6>Partition check:
<6> hda: hda1 hda2 hda3 hda4
<6> hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 hdb7 hdb8 >
<6>ide-floppy driver 0.99.newide
<6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 4096 buckets, 32Kbytes
<6>TCP: Hash tables configured (established 32768 bind 32768)
<6>Linux IP multicast router 0.06 plus PIM-SM
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<6>cryptoapi: loaded
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 1120k freed
<4>VFS: Mounted root (ext2 filesystem).
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<4>        <Adaptec 29160 Ultra160 SCSI adapter>
<4>        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
<4>
<4>blk: queue df521618, I/O limit 4095Mb (mask 0xffffffff)
<4>(scsi0:A:1): 20.000MB/s transfers (20.000MHz, offset 15)
<4>(scsi0:A:2): 10.000MB/s transfers (10.000MHz, offset 8)
<4>(scsi0:A:3): 20.000MB/s transfers (20.000MHz, offset 16)
<4>(scsi0:A:8): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
<4>  Vendor: IOMEGA    Model: ZIP 100           Rev: E.08
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>blk: queue df521418, I/O limit 4095Mb (mask 0xffffffff)
<4>  Vendor: PLEXTOR   Model: CD-ROM PX-32TS    Rev: 1.03
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>blk: queue df521818, I/O limit 4095Mb (mask 0xffffffff)
<4>  Vendor: PLEXTOR   Model: CD-R   PX-R412C   Rev: 1.05
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>blk: queue df52e818, I/O limit 4095Mb (mask 0xffffffff)
<4>  Vendor: PLEXTOR   Model: CD-R   PX-W1210S  Rev: 1.05
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>blk: queue df521a18, I/O limit 4095Mb (mask 0xffffffff)
<4>  Vendor: QUANTUM   Model: ATLAS10K2-TY367L  Rev: DA40
<4>  Type:   Direct-Access                      ANSI SCSI revision: 03
<4>blk: queue df521c18, I/O limit 4095Mb (mask 0xffffffff)
<4>scsi0:A:8:0: Tagged Queuing enabled.  Depth 32
<4>Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
<4>Attached scsi disk sdb at scsi0, channel 0, id 8, lun 0
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Current sd00:00: sense key Not Ready
<4>Additional sense indicates Medium not present
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<4>SCSI device sdb: 71721820 512-byte hdwr sectors (36722 MB)
<6> sdb: sdb1 sdb2 sdb3 sdb4
<6>Journalled Block Device driver loaded
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>Freeing unused kernel memory: 188k freed
<6>md: Autodetecting RAID arrays.
<6>md: autorun ...
<6>md: ... autorun DONE.
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,18), internal journal
<6>device-mapper: 4.0.1-ioctl (2003-07-12) initialised: [email protected]
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,18), internal journal
<6>lvm-mp: allocating 42 lowmem entries at c215b000
<6>LVM version 1.0.5+(mp-v6c)(22/07/2002) module loaded
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Current sd00:00: sense key Not Ready
<4>Additional sense indicates Medium not present
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: Write Protect is off
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<6>Device not ready.  Make sure there is a disc in the drive.
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Current sd00:00: sense key Not Ready
<4>Additional sense indicates Medium not present
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: Write Protect is off
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 2097144
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<6>Device not ready.  Make sure there is a disc in the drive.
<4> I/O error: dev 08:00, sector 0
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,18), internal journal
<4>EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
<4>EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
<6>kjournald starting.  Commit interval 5 seconds
<6>EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,70), internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<6>NTFS driver 2.1.4a [Flags: R/O MODULE].
<6>NTFS volume version 3.1.
<6>NTFS volume version 3.1.
<6>NTFS volume version 3.1.
<6>Adding Swap: 1060248k swap-space (priority -1)
<4>hdc: attached ide-scsi driver.
<6>scsi1 : SCSI host adapter emulation for IDE ATAPI devices
<4>  Vendor: SONY      Model: DVD RW DRU-500A   Rev: 1.0d
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>hdc: CHECK for good STATUS
Kernel logging (ksyslog) stopped.
Kernel log daemon terminating.

Boot logging started on /dev/tty1(/dev/console) at Sun Dec 21 20:54:26 2003

<notice>run boot scripts (setserial boot.proc)
Configuring serial ports...
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Configured serial ports
done<notice>exit status of (setserial boot.proc) is (0 0)
<notice>run boot scripts (boot.md boot.device-mapper)
Run file system check on root for device mapper setup
fsck 1.34 (25-Jul-2003)
suse-root (/dev/sdb2): clean, 268175/1452480 files, 1253785/2899732 blocks
doneRemounting root file system (/) read/write...
Activating device mapper...
Creating /dev/mapper/control character device with major:10 minor:63.
Remounting root file system (/) read-only again...
done
<notice>exit status of (boot.md boot.device-mapper) is (0 0)
<notice>run boot scripts (boot.lvm)
Run file system check on root for LVM activation
fsck 1.34 (25-Jul-2003)
suse-root (/dev/sdb2): clean, 268175/1452480 files, 1253785/2899732 blocks
doneRemounting root file system (/) read/write for vgscan...
Scanning for LVM volume groups...
vgscan -- reading all physical volumes (this may take a while...)
vgscan -- "/etc/lvmtab" and "/etc/lvmtab.d" successfully created
vgscan -- WARNING: This program does not do a VGDA backup of your volume group

Activating LVM volume groups...
vgchange -- no volume groups found

done
<notice>exit status of (boot.lvm) is (0)
<notice>run boot scripts (boot.localfs)
Checking file systems...
fsck 1.34 (25-Jul-2003)
suse-root (/dev/sdb2): clean, 268175/1452480 files, 1253785/2899732 blocks
doneMounting local file systems...
proc on /proc type proc (rw)
devpts on /dev/pts type devpts (rw,mode=0620,gid=5)
/dev/hdb2 on /Other/Linux/Boot/Main type ext2 (rw)
/dev/hdb3 on /Other/Linux/Boot/Test type ext2 (rw)
/dev/hdb6 on /Other/Linux/Root/RedHat type ext3 (rw)
/dev/hda1 on /Other/Windows/Windows98/Windows98 type vfat (rw,shortname=mixed)
/dev/hdb1 on /Other/Windows/Windows98/X-Files type vfat (rw,shortname=mixed)
/dev/hda2 on /Other/Windows/Windows2000/System type ntfs (ro)
/dev/hda3 on /Other/Windows/Windows2000/TA102140W2KT type ntfs (ro)
/dev/hda4 on /Other/Windows/Windows2000/Test type ntfs (ro)
done<notice>exit status of (boot.localfs) is (0)
<notice>run boot scripts (boot.crypto)
<notice>exit status of (boot.crypto) is (0)
<notice>run boot scripts (boot.swap boot.scpm boot.restore_permissions boot.loadmodules)
Activating remaining swap-devices in /etc/fstab...
doneMounting shared memory FS on /dev/shmdone
Loading required kernel modules
doneRestore device permissionsdone
<notice>exit status of (boot.swap boot.scpm boot.restore_permissions boot.loadmodules) is (0 0 0 0)
<notice>run boot scripts (boot.idedma boot.clock)
Setting up IDE DMA mode

/dev/hdc:
 setting using_dma to 1 (on)
 setting xfermode to 66 (UltraDMA mode2)
 using_dma    =  1 (on)
done
Setting up the CMOS clockdone
<notice>exit status of (boot.idedma boot.clock) is (0 0)
<notice>run boot scripts (boot.quota)
<notice>exit status of (boot.quota) is (0)
<notice>run boot scripts (boot.ldconfig)
Setting up timezone datadone
<notice>exit status of (boot.ldconfig) is (0)
<notice>run boot scripts (boot.sched boot.localnet boot.isapnp)
Setting scheduling timeslices unused
Setting up hostname 'suse-wkst1'done
Setting up loopback interface done
<notice>exit status of (boot.sched boot.localnet boot.isapnp) is (6 0 0)
<notice>run boot scripts (boot.klog boot.ipconfig)
Enabling syn flood protectiondone
Disabling IP forwardingdone
Creating /var/log/boot.msg
done<notice>killproc: kill(42,29)
System Boot Control: The system has been setup
Skipped features: boot.sched
System Boot Control: Running /etc/init.d/boot.local
<notice>exit status of (boot.klog boot.ipconfig) is (0 0)
done<notice>killproc: kill(42,3)


Boot logging started on /dev/tty1(/dev/console) at Sun Dec 21 21:54:34 2003

Master Resource Control: previous runlevel: N, switching to runlevel: 5
<notice>start services (random isdn)
Initializing random number generatordone
<notice>exit status of (random isdn) is (0 0)
<notice>start services (network)
Setting up network interfaces:
    lo        done
    eth0      IP/Netmask: 169.254.1.11 / 255.255.0.0  done
    eth1      (DHCP) <notice>startproc: execve (/sbin/dhcpcd) [ /sbin/dhcpcd -D -N -t 999999 -h suse-wkst1 eth1 ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh OLDPWD=/etc/sysconfig/network progress=18 INIT_VERSION=sysvinit-2.82 RUN_FROM_RC=yes REDIRECT=/dev/tty1 COLUMNS=80 PATH=/sbin:/usr/sbin:/bin:/usr/bin:/etc/sysconfig/network/scripts RUNLEVEL=5 PWD=/etc/sysconfig/network PREVLEVEL=N LINES=25 HOME=/ SHLVL=4 sscripts=38 _=/sbin/startproc DAEMON=/sbin/dhcpcd ]
<notice>pidofproc: dhcpcd 672
IP/Netmask: 10.0.0.39 / 255.255.255.0done
    ppp0      manual
<notice>exit status of (network) is (0)
<notice>start services (syslog)
Starting syslog services<notice>startproc: execve (/sbin/syslogd) [ /sbin/syslogd -a /var/lib/dhcp/dev/log -a /var/lib/named/dev/log ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=19 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/sbin/syslogd ]
<notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -2 ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=19 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/sbin/klogd ]
done
<notice>exit status of (syslog) is (0)
<notice>start services (hotplug)
Starting hotplugging services [ ieee1394 net pci usb .. ]done
<notice>exit status of (hotplug) is (0)
<notice>start services (resmgr)
Starting resource manager<notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=21 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/sbin/resmgrd ]
done
<notice>exit status of (resmgr) is (0)
<notice>start services (splash_early portmap)
Starting RPC portmap daemon<notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=22 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/sbin/portmap ]
done
<notice>exit status of (splash_early portmap) is (0 0)
<notice>start services (smbfs)
Mount SMB File System unused
<notice>exit status of (smbfs) is (6)
<notice>start services (sshd fbset alsasound acpid)
<notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=25 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/sshd ]
<notice>startproc: execve (/usr/sbin/acpid) [ /usr/sbin/acpid ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=25 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/acpid ]
Loading ACPI modules (ac battery button fan processor thermal ) done
Starting acpid done
Starting SSH daemondone
Starting sound driver:  emu10k1done
Restoring the previous sound settingdone
<notice>exit status of (sshd fbset alsasound acpid) is (0 0 0 0)
<notice>start services (splash kbd cups)
<notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=29 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ]
Starting cupsddone
Loading keymap azerty/be-latin1.map.gz
doneLoading compose table winkeys shiftctrl latin1.adddone
Stop Unicode mode
doneLoading console font lat1-16.psfu  -m none (B
done<notice>exit status of (splash kbd cups) is (5 0 0)
<notice>start services (smpppd postfix hwscan)
<notice>startproc: execve (/usr/sbin/smpppd) [ /usr/sbin/smpppd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=32 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/smpppd ]
Starting hardware scan on bootStarting SMPPPDdone
Starting mail service (Postfix)done
<notice>exit status of (smpppd postfix hwscan) is (0 0 0)
<notice>start services (xdm)
Starting service kdm<notice>startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ LC_MONETARY= CONSOLE=/dev/console TERM=linux SHELL=/bin/sh LC_NUMERIC= QTDIR=/usr/lib/qt3 LC_ALL= progress=35 INIT_VERSION=sysvinit-2.82 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin LC_MESSAGES= RUNLEVEL=5 LC_COLLATE= PWD=/ LANG=en_GB PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 XCURSOR_THEME=blueprint-cursor-theme no_proxy=localhost WINDOWMANAGER=/usr/X11R6/bin/kde LC_CTYPE=en_GB sscripts=38 LC_TIME= _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ]
done
<notice>exit status of (xdm) is (0)
<notice>start services (nscd cron)
<notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=36 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/nscd ]
<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh progress=36 INIT_VERSION=sysvinit-2.82 REDIRECT=/dev/tty1 COLUMNS=80 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin RUNLEVEL=5 PWD=/ PREVLEVEL=N LINES=25 HOME=/ SHLVL=2 sscripts=38 _=/sbin/startproc DAEMON=/usr/sbin/cron ]
Starting Name Service Cache Daemondone
Starting CRON daemondone
<notice>exit status of (nscd cron) is (0 0)
<notice>start services (splash_late)
Master Resource Control: runlevel 5 has been reached
Skipped services in runlevel 5: smbfs splash
<notice>exit status of (splash_late) is (0)
<notice>killproc: kill(461,3)