APIC error
Ed Westphal <[email protected]>
| Newsgroups | org.kernel.vger.linux-smp |
|---|---|
| Message-ID | <[email protected]> |
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09 Total of 2 processors activated (12753.30 BogoMIPS). ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-20 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 29. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00178020 ....... : arbitration: 00 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 0 0 0 0 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 1 1 0 0 0 1 1 71 0a 003 03 0 0 0 0 0 1 1 79 0b 003 03 0 0 0 0 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 0 0 0 0 0 1 1 A1 10 003 03 1 1 0 1 0 1 1 A9 11 003 03 1 1 0 1 0 1 1 B1 12 003 03 1 1 0 1 0 1 1 B9 13 003 03 1 1 0 1 0 1 1 C1 14 000 00 1 0 0 0 0 0 0 00 15 003 03 1 1 0 1 0 1 1 C9 16 003 03 1 1 0 1 0 1 1 D1 17 003 03 1 1 0 1 0 1 1 D9 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ21 -> 0:21 IRQ22 -> 0:22 IRQ23 -> 0:23 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 3191.8903 MHz. ..... host bus clock speed is 199.4931 MHz. cpu: 0, clocks: 1994931, slice: 664977 CPU0<T0:1994928,T1:1329936,D:15,S:664977,C:1994931> cpu: 1, clocks: 1994931, slice: 664977 CPU1<T0:1994928,T1:664960,D:14,S:664977,C:1994931> cpu_sibling_map[0] = 1 cpu_sibling_map[1] = 0 mapping CPU#0's runqueue to CPU#1's runqueue. Please advise. Thanks. -- Ed Westphal <[email protected]>