unexpected IO-APIC
"Mike Farnam" <[email protected]> Mon, 28 Feb 2005 15:34:01 -0800
| Newsgroups | org.kernel.vger.linux-smp |
|---|---|
| Message-ID | <[email protected]> |
io-apic.txt
(text/plain, 15.3 KB)
[root@localhost root]# dmesg n CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 3578.26 BogoMIPS CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Intel machine check reporting enabled on CPU#1. CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000 CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000 CPU1: AMD Opteron(tm) Processor 844 stepping 0a Total of 2 processors activated (7156.53 BogoMIPS). ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. Setting 3 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 3 ... ok. Setting 4 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 4 ... ok. Setting 5 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 5 ... ok. Setting 6 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 6 ... ok. Setting 7 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 7 ... ok. Setting 8 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 8 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-18, 2-20, 2-21, 2-22, 2-23, 3-0, 4-0, 4-1, 4-2, 4-3, 5-1, 5-2, 5-3, 6-1, 6-2, 6-3, 7-1, 7-2, 7-3, 8-1, 8-2, 8-3 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 26. number of IO-APIC #2 registers: 24. number of IO-APIC #3 registers: 4. number of IO-APIC #4 registers: 4. number of IO-APIC #5 registers: 4. number of IO-APIC #6 registers: 4. number of IO-APIC #7 registers: 4. number of IO-APIC #8 registers: 4. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00170011 ....... : max redirection entries: 0017 ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 02000000 ....... : arbitration: 02 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 1 1 0 1 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 1 1 0 1 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 0 0 0 0 0 1 1 71 0a 003 03 1 1 0 1 0 1 1 79 0b 003 03 1 1 0 1 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 003 03 1 1 0 1 0 1 1 A9 12 000 00 1 0 0 0 0 0 0 00 13 003 03 1 1 0 1 0 1 1 B1 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IO APIC #3...... .... register #00: 03000000 ....... : physical APIC id: 03 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 1 1 0 1 0 1 1 B9 02 003 03 1 1 0 1 0 1 1 C1 03 003 03 1 1 0 1 0 1 1 C9 IO APIC #4...... .... register #00: 04000000 ....... : physical APIC id: 04 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 IO APIC #5...... .... register #00: 05000000 ....... : physical APIC id: 05 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 003 03 1 1 0 1 0 1 1 D1 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 IO APIC #6...... .... register #00: 06000000 ....... : physical APIC id: 06 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 003 03 1 1 0 1 0 1 1 D9 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 IO APIC #7...... .... register #00: 07000000 ....... : physical APIC id: 07 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 003 03 1 1 0 1 0 1 1 E1 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 IO APIC #8...... .... register #00: 08000000 ....... : physical APIC id: 08 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00030011 ....... : max redirection entries: 0003 An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 003 03 1 1 0 1 0 1 1 E9 01 000 00 1 0 0 0 0 0 0 00 02 000 00 1 0 0 0 0 0 0 00 03 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ17 -> 0:17 IRQ19 -> 0:19 IRQ25 -> 1:1 IRQ26 -> 1:2 IRQ27 -> 1:3 IRQ32 -> 3:0 IRQ36 -> 4:0 IRQ40 -> 5:0 IRQ44 -> 6:0 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1792.6099 MHz. ..... host bus clock speed is 199.1788 MHz. cpu: 0, clocks: 1991788, slice: 663929 CPU0<T0:1991776,T1:1327840,D:7,S:663929,C:1991788> cpu: 1, clocks: 1991788, slice: 663929 CPU1<T0:1991776,T1:663904,D:14,S:663929,C:1991788> zapping low mappings. Process timing init...done. Starting migration thread for cpu 0 Starting migration thread for cpu 1 PCI: PCI BIOS revision 2.10 entry at 0xfd771, last bus=48 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Discovered primary peer bus 20 [IRQ] PCI: Using IRQ router default [1022/746b] at 00:07.3 PCI->APIC IRQ transform: (B1,I0,P3) -> 19 PCI->APIC IRQ transform: (B1,I0,P3) -> 19 PCI->APIC IRQ transform: (B1,I5,P0) -> 17 PCI->APIC IRQ transform: (B2,I2,P0) -> 25 PCI->APIC IRQ transform: (B2,I3,P0) -> 26 PCI->APIC IRQ transform: (B2,I4,P0) -> 27 PCI->APIC IRQ transform: (B32,I1,P0) -> 32 PCI->APIC IRQ transform: (B32,I2,P0) -> 36 PCI->APIC IRQ transform: (B32,I3,P0) -> 40 PCI->APIC IRQ transform: (B32,I4,P0) -> 44 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS not found. Total HugeTLB memory allocated, 0 Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces VFS: Disk quotas vdquot_6.5.1 aio_setup: num_physpages = 131036 aio_setup: sizeof(struct page) = 56 Hugetlbfs mounted. pty: 2048 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS0 at 0x03f8 (irq = 4) is a 16550A ttyS1 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10e NET4: Frame Diverter 0.46 RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD8111: IDE controller at PCI slot 00:07.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AMD_IDE: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) UDMA100 controller on pci00:07.1 ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio hdc: DV-28E-C, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 ide-floppy driver 0.99.newide ide-floppy driver 0.99.newide md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 16384 buckets, 128Kbytes TCP: Hash tables configured (established 524288 bind 65536) Linux IP multicast router 0.06 plus PIM-SM Initializing IPsec netlink socket NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 275k freed VFS: Mounted root (ext2 filesystem). SCSI subsystem driver Revision: 1.00 Fusion MPT base driver 2.05.16.02 Copyright (c) 1999-2004 LSI Logic Corporation mptbase: Initiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator} mptbase: 1 MPT adapter found, 1 installed. Fusion MPT SCSI Host driver 2.05.16.02 scsi0 : ioc0: LSI53C1030, FwRev=01032300h, Ports=1, MaxQ=222, IRQ=27 blk: queue c4c3e218, I/O limit 4294967295Mb (mask 0xffffffffffffffff) Vendor: SEAGATE Model: ST373307LC Rev: 0007 Type: Direct-Access ANSI SCSI revision: 03 blk: queue c4c3e018, I/O limit 4294967295Mb (mask 0xffffffffffffffff) Vendor: SDR Model: GEM318P Rev: 1 Type: Processor ANSI SCSI revision: 02 blk: queue c4ef4e18, I/O limit 4294967295Mb (mask 0xffffffffffffffff) Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB) Partition check: sda: sda1 sda2 sda3 Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 228k freed usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xf88a0000, IRQ 19 usb-ohci.c: usb-01:00.0, Advanced Micro Devices [AMD] AMD-8111 USB usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected usb-ohci.c: USB OHCI at membase 0xf88a2000, IRQ 19 usb-ohci.c: usb-01:00.1, Advanced Micro Devices [AMD] AMD-8111 USB (#2) usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal Adding Swap: 2040244k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 3 inserting floppy driver for 2.4.21-27.0.2.ELsmp Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 tg3.c:v3.10RH (September 14, 2004) divert: allocating divert_blk for eth0 eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:be:07 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] divert: allocating divert_blk for eth1 eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:be:08 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] divert: freeing divert_blk for eth0 divert: freeing divert_blk for eth1 ip_tables: (C) 2000-2002 Netfilter core team tg3.c:v3.10RH (September 14, 2004) divert: allocating divert_blk for eth0 eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:be:07 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] divert: allocating divert_blk for eth1 eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:be:08 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] ip_tables: (C) 2000-2002 Netfilter core team tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. audit subsystem ver 0.1 initialized Audit daemon registered (process 1428) lp: driver loaded but no devices found usb.c: registered new driver serial usbserial.c: USB Serial support registered for Generic usbserial.c: USB Serial Driver core v1.4 ipmi message handler version v27 ipmi device interface version v27 ipmi_kcs: smbios says to use port addr 0x00A2, irq 25 ipmi_kcs: ipmi_kcs unable to claim interrupt 25, running polled ipmi_kcs: Acquiring BMC @ port=0xa2 [root@localhost root]#