Re: [PATCH v2 1/2] wifi: cfg80211: report authorized connect and roam events

On 8/5/2026 4:01 AM, Jason Huang wrote:
> From: Jason Huang <[email protected]>
> 
> Drivers that offload the 802.1X/FT key exchange can know that
> the link is ready for data traffic when reporting a successful
> connect or roam event. Carry that state through cfg80211 and
> include NL80211_ATTR_PORT_AUTHORIZED in the corresponding nl80211
> notification when the driver provides it.
> 
> This lets userspace avoid restarting authentication state machines
> after firmware has already completed the security exchange during
> offloaded roaming.
> 
> Assisted-by: GitHub Copilot CLI:gpt-5.5
> Signed-off-by: Chung-Hsien Hsu <[email protected]>
> Signed-off-by: Chi-hsien Lin <[email protected]>

Jason,
why are the above signing off the patch if you are the author?

> Signed-off-by: Jason Huang <[email protected]>
> ---
>  include/net/cfg80211.h       | 6 ++++++
>  include/uapi/linux/nl80211.h | 4 +++-
>  net/wireless/nl80211.c       | 6 +++++-
>  net/wireless/sme.c           | 2 ++
>  4 files changed, 16 insertions(+), 2 deletions(-)
> 
> diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
> index 97c16d4ff127..7f576bb7325c 100644
> --- a/include/net/cfg80211.h
> +++ b/include/net/cfg80211.h
> @@ -9103,6 +9103,8 @@ struct cfg80211_fils_resp_params {
>   * @assoc_encrypted: The driver should set this flag to indicate that the
>   *	(Re)Association Request/Response frames are transmitted encrypted over
>   *	the air.
> + * @authorized: Indicates whether the connection is ready to transport data
> + *	packets.
>   */
>  struct cfg80211_connect_resp_params {
>  	int status;
> @@ -9113,6 +9115,7 @@ struct cfg80211_connect_resp_params {
>  	struct cfg80211_fils_resp_params fils;
>  	enum nl80211_timeout_reason timeout_reason;
>  	bool assoc_encrypted;
> +	bool authorized;
>  
>  	const u8 *ap_mld_addr;
>  	u16 valid_links;
> @@ -9281,6 +9284,8 @@ cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid,
>   * @links.bss: For MLO roaming, entry of new bss to which STA link got
>   *	roamed. For non-MLO roaming, links[0].bss points to entry of bss to
>   *	which STA got roamed (may be %NULL if %links.bssid is set)
> + * @authorized: Indicates whether the new connection is ready to transport data
> + *	packets.
>   */
>  struct cfg80211_roam_info {
>  	const u8 *req_ie;
> @@ -9297,6 +9302,7 @@ struct cfg80211_roam_info {
>  		struct ieee80211_channel *channel;
>  		struct cfg80211_bss *bss;
>  	} links[IEEE80211_MLD_MAX_NUM_LINKS];
> +	bool authorized;
>  };
>  
>  /**
> diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
> index 020387d76412..66b4cfd8de86 100644
> --- a/include/uapi/linux/nl80211.h
> +++ b/include/uapi/linux/nl80211.h
> @@ -2705,7 +2705,9 @@ enum nl80211_commands {
>   *	in %NL80211_CMD_CONNECT to indicate that for 802.1X authentication it
>   *	wants to use the supported offload of the 4-way handshake.
>   * @NL80211_ATTR_PMKR0_NAME: PMK-R0 Name for offloaded FT.
> - * @NL80211_ATTR_PORT_AUTHORIZED: (reserved)
> + * @NL80211_ATTR_PORT_AUTHORIZED: flag attribute used in %NL80211_CMD_CONNECT
> + *	or %NL80211_CMD_ROAM notifications to indicate that 802.1X
> + *	authentication was done by the driver or is not needed.

This attribute became deprecated when NL80211_CMD_PORT_AUTHORIZED was
introduced. Why are you not using that?

503c1fb98ba3 ("cfg80211/nl80211: add a port authorized event")