Re: [PATCH v2 2/2] dt-bindings: net: convert wiznet,w5x00 to YAML

On 04/08/2026 19:40, Arthur Crépin Leblond wrote:
> Convert the Wiznet w5x00 SPI Ethernet controller binding from
> text to DT schema format.

Limited review, to spare you one review cycle, as it was not tested.

Subject: s/YAML/DT schema/

See also:
https://elixir.bootlin.com/linux/v7.1-rc7/source/Documentation/devicetree/bindings/submitting-patches.rst#L23

> 
> Signed-off-by: Arthur Crépin Leblond <[email protected]>
> ---
>  .../devicetree/bindings/net/wiznet,w5x00.txt       |  50 ----------
>  .../devicetree/bindings/net/wiznet,w5x00.yaml      | 103 +++++++++++++++++++++
>  2 files changed, 103 insertions(+), 50 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
> deleted file mode 100644
> index e9665798c4be..000000000000
> --- a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
> +++ /dev/null
> @@ -1,50 +0,0 @@
> -* Wiznet w5x00
> -
> -This is a standalone 10/100 MBit Ethernet controller with SPI interface.
> -
> -For each device connected to a SPI bus, define a child node within
> -the SPI master node.
> -
> -Required properties:
> -- compatible: Should be one of the following strings:
> -	      "wiznet,w5100"
> -	      "wiznet,w5200"
> -	      "wiznet,w5500"
> -- reg: Specify the SPI chip select the chip is wired to.
> -- interrupts: Specify the interrupt index within the interrupt controller (referred
> -              to above in interrupt-parent) and interrupt type. w5x00 natively
> -              generates falling edge interrupts, however, additional board logic
> -              might invert the signal.
> -- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
> -- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
> -             see also generic and your platform specific pinctrl binding
> -             documentation.
> -
> -Optional properties:
> -- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500.
> -  According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however,
> -  board designs may need to limit this value.
> -- local-mac-address: See ethernet.txt in the same directory.
> -
> -
> -Example (for Raspberry Pi with pin control stuff for GPIO irq):
> -
> -&spi {
> -	ethernet@0: w5500@0 {
> -		compatible = "wiznet,w5500";
> -		reg = <0>;
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&eth1_pins>;
> -		interrupt-parent = <&gpio>;
> -		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> -		spi-max-frequency = <30000000>;
> -	};
> -};
> -
> -&gpio {
> -	eth1_pins: eth1_pins {
> -		brcm,pins = <25>;
> -		brcm,function = <0>; /* in */
> -		brcm,pull = <0>; /* none */
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.yaml b/Documentation/devicetree/bindings/net/wiznet,w5x00.yaml
> new file mode 100644
> index 000000000000..8f45a5d773fe
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.yaml

Filename: wiznet,w5100.yaml

> @@ -0,0 +1,103 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/wiznet,w5x00.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Wiznet w5x00 SPI Ethernet Controller
> +
> +description: |
> +  This is a standalone 10/100 MBit Ethernet controller with SPI interface.
> +
> +  For each device connected to a SPI bus, define a child node within the SPI master node.

This looks unwrapped (see Linux coding style).

> +
> +allOf:
> +  - $ref: /schemas/net/ethernet-controller.yaml#
> +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - wiznet,w5100
> +      - wiznet,w5200
> +      - wiznet,w5500
> +
> +  reg:
> +    description: Specify the SPI chip select the chip is wired to.
> +    maxItems: 1
> +    minItems: 1

Drop, please do not invent your own syntax. Look at recently reviewed
code or example-schema.

> +
> +  interrupts:
> +    description:
> +      Specify the interrupt index within the interrupt controller (referred to
> +      above in interrupt-parent) and interrupt type. w5x00 natively generates
> +      falling edge interrupts, however, additional board logic might invert the
> +      signal.
> +    maxItems: 1
> +    minItems: 1
> +
> +  pinctrl-names:
> +    description:
> +      List of assigned state names, see pinctrl binding documentation.
> +    enum:
> +      - default
> +    minItems: 1

Do not invent own code. Drop

> +
> +  pinctrl-0:
> +    description:
> +      List of phandles to configure the GPIO pin used as interrupt line, see
> +      also generic and your platform specific pinctrl binding documentation.
> +    minItems: 1
> +
> +  local-mac-address: true
> +
> +  spi-max-frequency:
> +    description:
> +      Maximum frequency of the SPI bus when accessing the w5500. According to
> +      the w5500 datasheet, the chip allows a maximum of 80 MHz, however, board
> +      designs may need to limit this value.
> +    maximum: 80000000
> +
> +  link-gpios:
> +    description: A GPIO line used for the link detection interrupt.
> +    maxItems: 1

This wasn't in the original binding and lacks explanation in commit msg.
Any change done to the binding must be documented with a reason WHY. If
there is no reason WHY, then maybe you wanted separate commit (although
each commit should explain WHY).

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - pinctrl-names
> +  - pinctrl-0
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    /* Example (for Raspberry Pi with pin control stuff for GPIO irq) */
> +
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    spi {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        ethernet@0: w5500@0 {
> +          compatible = "wiznet,w5500";
> +            reg = <0>;
> +            pinctrl-names = "default";

Messed indentation.

> +            pinctrl-0 = <&eth1_pins>;
> +            interrupt-parent = <&gpio>;
> +            interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +            spi-max-frequency = <30000000>;
> +            link-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
> +            local-mac-address = [ a0 b0 c0 d0 e0 f0 ];
> +        };
> +    };
> +
> +    &gpio {
> +      eth1_pins: eth1_pins {
> +        brcm,pins = <25 4>;
> +        brcm,function = <0 0>; /* in */
> +        brcm,pull = <0 0>; /* none */
> +    };

Irrelevant node, drop

Best regards,
Krzysztof