Re: [PATCHv3 net-next] net: dsa: b53: srab: propagate errors from init helpers

Hi,

On Wed, Jul 29, 2026 at 10:29 PM Rosen Penev <[email protected]> wrote:
>
> Convert b53_srab_prepare_irq() and b53_srab_mux_init() from void to
> int-returning functions so probe failures are properly propagated.
>
> b53_srab_prepare_irq() now returns -ENOMEM on allocation failure and
> -EPROBE_DEFER if any port IRQ is not yet available.
>
> b53_srab_mux_init() now returns PTR_ERR on ioremap failure instead of
> silently ignoring it.
>
> Check and propagate both return values in b53_srab_probe() so the
> driver core sees the real error instead of always reaching
> b53_switch_register().
>
> Add error handling in probe as a result of b53_srab_prepare_irq().
>
> Move mux_config out of private struct. This was needed when devm was not used.
>
> Assisted-by: Opencode:Big-Pickle
> Signed-off-by: Rosen Penev <[email protected]>
> ---
>  v3: move mux_config to function.
>  v2: address memory leak in b53_srab_prepare_irq().

Please also mention any review comments you addressed in the
changelog. I don't see any mention of changing the condition in
b53_srab_mux_init().

>  drivers/net/dsa/b53/b53_srab.c | 46 ++++++++++++++++++++++++----------
>  1 file changed, 33 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/net/dsa/b53/b53_srab.c b/drivers/net/dsa/b53/b53_srab.c
> index b9939bbd2cd5..81bfd5cd1022 100644
> --- a/drivers/net/dsa/b53/b53_srab.c
> +++ b/drivers/net/dsa/b53/b53_srab.c

(snip)

> @@ -622,6 +628,7 @@ static int b53_srab_probe(struct platform_device *pdev)
>         const struct of_device_id *of_id = NULL;
>         struct b53_srab_priv *priv;
>         struct b53_device *dev;
> +       int err;
>
>         if (dn)
>                 of_id = of_match_node(b53_srab_of_match, dn);
> @@ -651,10 +658,23 @@ static int b53_srab_probe(struct platform_device *pdev)
>
>         platform_set_drvdata(pdev, dev);
>
> -       b53_srab_prepare_irq(pdev);
> -       b53_srab_mux_init(pdev);
> +       err = b53_srab_prepare_irq(pdev);
> +       if (err)
> +               return err;
> +
> +       err = b53_srab_mux_init(pdev);
> +       if (err)
> +               goto err_irq;

Tbh, I'm not sure if it is a good idea to abort probing on error here.
The mux only applies to 2 of the 6? potential ports, so at worst those
two ports won't work, but other ports should continue to work fine.
And I think reduced functionality is preferable to no functionality;
with a non-probing switch it will likely be harder to recover the
device.

(The values read out from mux could even just be passed on via
phy-mode properties on the ports in the device tree, but that would
require changing the driver ...).

Best regards,
Jonas