[PATCH net-next v4 1/3] dt-bindings: net: wiznet,w5100: convert to DT schema

Convert the Wiznet w5x00 SPI Ethernet controller binding from
plain text to DT schema.

Signed-off-by: Arthur Crépin Leblond <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
---
 .../devicetree/bindings/net/wiznet,w5100.yaml      | 67 ++++++++++++++++++++++
 .../devicetree/bindings/net/wiznet,w5x00.txt       | 50 ----------------
 2 files changed, 67 insertions(+), 50 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/wiznet,w5100.yaml b/Documentation/devicetree/bindings/net/wiznet,w5100.yaml
new file mode 100644
index 000000000000..641c9ddbde9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wiznet,w5100.yaml
@@ -0,0 +1,67 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/wiznet,w5100.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Wiznet w5100/w5200/w5500 SPI Ethernet Controller
+
+maintainers:
+  - Arthur Crépin Leblond <[email protected]>
+
+description: |
+  This is a standalone 10/100 MBit Ethernet controller with SPI interface.
+
+allOf:
+  - $ref: /schemas/net/ethernet-controller.yaml#
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+properties:
+  compatible:
+    enum:
+      - wiznet,w5100
+      - wiznet,w5200
+      - wiznet,w5500
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency:
+    description:
+      According to the w5500 datasheet, the chip allows a maximum of 80 MHz,
+      however, board designs may need to limit this value.
+    maximum: 80000000
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    /* Example (for Raspberry Pi with pin control stuff for GPIO irq) */
+
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet@0 {
+            compatible = "wiznet,w5500";
+            reg = <0>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&eth1_pins>;
+            interrupt-parent = <&gpio>;
+            interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+            spi-max-frequency = <30000000>;
+            local-mac-address = [ a0 b0 c0 d0 e0 f0 ];
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
deleted file mode 100644
index e9665798c4be..000000000000
--- a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-* Wiznet w5x00
-
-This is a standalone 10/100 MBit Ethernet controller with SPI interface.
-
-For each device connected to a SPI bus, define a child node within
-the SPI master node.
-
-Required properties:
-- compatible: Should be one of the following strings:
-	      "wiznet,w5100"
-	      "wiznet,w5200"
-	      "wiznet,w5500"
-- reg: Specify the SPI chip select the chip is wired to.
-- interrupts: Specify the interrupt index within the interrupt controller (referred
-              to above in interrupt-parent) and interrupt type. w5x00 natively
-              generates falling edge interrupts, however, additional board logic
-              might invert the signal.
-- pinctrl-names: List of assigned state names, see pinctrl binding documentation.
-- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line,
-             see also generic and your platform specific pinctrl binding
-             documentation.
-
-Optional properties:
-- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500.
-  According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however,
-  board designs may need to limit this value.
-- local-mac-address: See ethernet.txt in the same directory.
-
-
-Example (for Raspberry Pi with pin control stuff for GPIO irq):
-
-&spi {
-	ethernet@0: w5500@0 {
-		compatible = "wiznet,w5500";
-		reg = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&eth1_pins>;
-		interrupt-parent = <&gpio>;
-		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <30000000>;
-	};
-};
-
-&gpio {
-	eth1_pins: eth1_pins {
-		brcm,pins = <25>;
-		brcm,function = <0>; /* in */
-		brcm,pull = <0>; /* none */
-	};
-};

-- 
2.55.0