[PATCH net v4 1/6] net: phy: split phy_probe() error paths

From: Xuanqiang Luo <[email protected]>

phy_probe() uses one cleanup path for failures at every initialization
stage. This runs cleanup for resources that have not been initialized.

Split the cleanup by initialization stage so each failure path unwinds
only the resources that may have been initialized.

Unregister LED triggers before releasing the SFP upstream and ports,
because the LED triggers are initialized after those resources and must
be unwound first.

Signed-off-by: Xuanqiang Luo <[email protected]>
---
 drivers/net/phy/phy_device.c | 20 +++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 94b2e85e00a37..2cf70471ae089 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -3706,7 +3706,7 @@ static int phy_probe(struct device *dev)
 	if (phydev->drv->probe) {
 		err = phydev->drv->probe(phydev);
 		if (err)
-			goto out;
+			goto out_reset;
 	}
 
 	phy_disable_interrupts(phydev);
@@ -3727,7 +3727,7 @@ static int phy_probe(struct device *dev)
 		err = genphy_read_abilities(phydev);
 
 	if (err)
-		goto out;
+		goto out_reset;
 
 	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			       phydev->supported))
@@ -3744,7 +3744,7 @@ static int phy_probe(struct device *dev)
 
 	err = phy_setup_ports(phydev);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	phy_advertise_supported(phydev);
 
@@ -3753,7 +3753,7 @@ static int phy_probe(struct device *dev)
 	 */
 	err = genphy_c45_read_eee_adv(phydev, phydev->advertising_eee);
 	if (err)
-		goto out;
+		goto out_sfp_release;
 
 	/* Get the EEE modes we want to prohibit. */
 	of_set_phy_eee_broken(phydev);
@@ -3806,20 +3806,22 @@ static int phy_probe(struct device *dev)
 	if (IS_ENABLED(CONFIG_PHYLIB_LEDS) && !phy_driver_is_genphy(phydev)) {
 		err = of_phy_leds(phydev);
 		if (err)
-			goto out;
+			goto out_unreg_led_triggers;
 	}
 
 	return 0;
 
-out:
+out_unreg_led_triggers:
+	if (!phydev->is_on_sfp_module)
+		phy_led_triggers_unregister(phydev);
+
+out_sfp_release:
 	sfp_bus_del_upstream(phydev->sfp_bus);
 	phydev->sfp_bus = NULL;
 
 	phy_cleanup_ports(phydev);
 
-	if (!phydev->is_on_sfp_module)
-		phy_led_triggers_unregister(phydev);
-
+out_reset:
 	/* Re-assert the reset signal on error */
 	phy_device_reset(phydev, 1);
 
-- 
2.43.0