Re: [PATCH v4 10/11] Input: stmfts - support FTS5

Hi David,

On Thu, Apr 09, 2026 at 12:15:53AM +0200, David Heidelberg via B4 Relay wrote:
> @@ -101,12 +129,27 @@ struct stmfts_data {
>  
>  	struct completion cmd_done;
>  
> +	unsigned long touch_id;
> +	unsigned long stylus_id;

I wonder why do you track contacts yourself instead of telling input
core to do it for you and report BTN_TOUCH as needed? You just need to
call input_mt_sync_frame() when you are done processing input frame.

Does the device send all contacts state in one transmission or it can
transmit contacts one by one?

> +
> +	/* Boundary check - some devices report max value, adjust */
> +	if (x >= sdata->prop.max_x)
> +		x = sdata->prop.max_x - 1;
> +	if (y >= sdata->prop.max_y)
> +		y = sdata->prop.max_y - 1;

It is allowed to exceed declared min and max, so this clampin is not
needed.

>  
> +static int stmfts5_set_scan_mode(struct stmfts_data *sdata, const u8 val)
> +{
> +	int err;
> +
> +	u8 scan_mode_cmd[3] = { STMFTS5_SET_SCAN_MODE, 0x00, val };
> +	struct i2c_msg msg = {
> +		.addr = sdata->client->addr,
> +		.len = sizeof(scan_mode_cmd),
> +		.buf = scan_mode_cmd,
> +	};
> +
> +	err = i2c_transfer(sdata->client->adapter, &msg, 1);

Is this i2c_master_send()?

> +	if (err != 1)
> +		return err < 0 ? err : -EIO;
> +
> +	return 0;
> +
> +}
> +
>  static int stmfts_input_open(struct input_dev *dev)
>  {
>  	struct stmfts_data *sdata = input_get_drvdata(dev);
> @@ -371,6 +622,28 @@ static int stmfts_input_open(struct input_dev *dev)
>  	return 0;
>  }
>  
> +static int stmfts5_input_open(struct input_dev *dev)
> +{
> +	struct stmfts_data *sdata = input_get_drvdata(dev);
> +	int err;
> +
> +	err = pm_runtime_resume_and_get(&sdata->client->dev);
> +	if (err)
> +		return err;
> +
> +	mutex_lock(&sdata->mutex);
> +	sdata->running = true;
> +	mutex_unlock(&sdata->mutex);

	scoped_guard(mutex, &sdata->mutex)
		sdata->running;

> +
> +	err = stmfts5_set_scan_mode(sdata, 0xff);
> +	if (err) {
> +		pm_runtime_put_sync(&sdata->client->dev);

Reset "running"?

> +		return err;
> +	}
> +
> +	return 0;
> +}
> +
>  static void stmfts_input_close(struct input_dev *dev)
>  {
>  	struct stmfts_data *sdata = input_get_drvdata(dev);
> @@ -404,6 +677,23 @@ static void stmfts_input_close(struct input_dev *dev)
>  	pm_runtime_put_sync(&sdata->client->dev);
>  }
>  
> +static void stmfts5_input_close(struct input_dev *dev)
> +{
> +	struct stmfts_data *sdata = input_get_drvdata(dev);
> +	int err;
> +
> +	err = stmfts5_set_scan_mode(sdata, 0x00);
> +	if (err)
> +		dev_warn(&sdata->client->dev,
> +			 "failed to disable touchscreen: %d\n", err);
> +
> +	mutex_lock(&sdata->mutex);
> +	sdata->running = false;
> +	mutex_unlock(&sdata->mutex);

scoped_guard()

> +
> +	pm_runtime_put_sync(&sdata->client->dev);
> +}
> +
>  static ssize_t stmfts_sysfs_chip_id(struct device *dev,
>  				struct device_attribute *attr, char *buf)
>  {
> @@ -484,10 +774,8 @@ static ssize_t stmfts_sysfs_hover_enable_write(struct device *dev,
>  	guard(mutex)(&sdata->mutex);
>  
>  	if (hover != sdata->hover_enabled) {
> -		if (sdata->running) {
> -			err = i2c_smbus_write_byte(sdata->client,
> -					   value ? STMFTS_SS_HOVER_SENSE_ON :
> -						   STMFTS_SS_HOVER_SENSE_OFF);
> +		if (sdata->running && sdata->ops->set_hover) {
> +			err = sdata->ops->set_hover(sdata, hover);
>  			if (err)
>  				return err;
>  		}
> @@ -612,7 +900,7 @@ static int stmfts_power_on(struct stmfts_data *sdata)
>  	if (sdata->reset_gpio)
>  		stmfts_reset(sdata);
>  
> -	err = stmfts_configure(sdata);
> +	err = sdata->ops->configure(sdata);
>  	if (err)
>  		regulator_bulk_disable(ARRAY_SIZE(stmfts_supplies),
>  				       sdata->supplies);
> @@ -620,6 +908,29 @@ static int stmfts_power_on(struct stmfts_data *sdata)
>  	return err;
>  }
>  
> +static int stmfts5_configure(struct stmfts_data *sdata)
> +{
> +	u8 event[STMFTS_EVENT_SIZE];
> +	int ret;
> +
> +	/* Verify I2C communication */
> +	ret = i2c_smbus_read_i2c_block_data(sdata->client,
> +					    STMFTS_READ_ALL_EVENT,
> +					    sizeof(event), event);
> +	if (ret < 0)
> +		return ret;
> +
> +	enable_irq(sdata->client->irq);
> +
> +	return 0;
> +}
> +
> +static void stmfts5_chip_power_off(struct stmfts_data *sdata)
> +{
> +	i2c_smbus_write_byte(sdata->client, STMFTS_SLEEP_IN);
> +	msleep(20);
> +}
> +
>  static void stmfts_power_off(void *data)
>  {
>  	struct stmfts_data *sdata = data;
> @@ -629,10 +940,73 @@ static void stmfts_power_off(void *data)
>  	if (sdata->reset_gpio)
>  		gpiod_set_value_cansleep(sdata->reset_gpio, 1);
>  
> +	if (sdata->ops->power_off)
> +		sdata->ops->power_off(sdata);
> +
>  	regulator_bulk_disable(ARRAY_SIZE(stmfts_supplies),
>  			       sdata->supplies);
>  }
>  
> +static int stmfts_setup_input(struct stmfts_data *sdata)
> +{
> +	struct device *dev = &sdata->client->dev;
> +
> +	input_set_abs_params(sdata->input, ABS_MT_ORIENTATION, 0, 255, 0, 0);
> +	input_set_abs_params(sdata->input, ABS_DISTANCE, 0, 255, 0, 0);
> +
> +	sdata->use_key = device_property_read_bool(dev, "touch-key-connected");
> +	if (sdata->use_key) {
> +		input_set_capability(sdata->input, EV_KEY, KEY_MENU);
> +		input_set_capability(sdata->input, EV_KEY, KEY_BACK);
> +	}
> +
> +	return input_mt_init_slots(sdata->input, STMFTS_MAX_FINGERS,
> +				   INPUT_MT_DIRECT);
> +}
> +
> +static int stmfts5_setup_input(struct stmfts_data *sdata)
> +{
> +	struct device *dev = &sdata->client->dev;
> +
> +	sdata->mode_switch_gpio = devm_gpiod_get_optional(dev, "mode-switch",
> +							  GPIOD_OUT_HIGH);
> +	if (IS_ERR(sdata->mode_switch_gpio))
> +		return dev_err_probe(dev, PTR_ERR(sdata->mode_switch_gpio),
> +				     "Failed to get GPIO 'switch'\n");
> +
> +	/* Mark as direct input device for calibration support */
> +	__set_bit(INPUT_PROP_DIRECT, sdata->input->propbit);
> +
> +	/* Set up basic touch capabilities */
> +	input_set_capability(sdata->input, EV_KEY, BTN_TOUCH);

This will be done by input_mt_init_slots(..., INPUT_MT_DIRECT). 

> +
> +	/* Set resolution for accurate calibration */
> +	if (!input_abs_get_res(sdata->input, ABS_MT_POSITION_X)) {
> +		input_abs_set_res(sdata->input, ABS_MT_POSITION_X, 10);
> +		input_abs_set_res(sdata->input, ABS_MT_POSITION_Y, 10);
> +	}
> +
> +	input_set_abs_params(sdata->input, ABS_MT_DISTANCE, 0, 255, 0, 0);
> +
> +	/* Enable stylus support if requested */
> +	sdata->stylus_enabled = device_property_read_bool(dev, "stylus-enabled");
> +
> +	/* Initialize touch tracking bitmaps */
> +	sdata->touch_id = 0;
> +	sdata->stylus_id = 0;
> +
> +	/* Initialize MT slots with support for pen tool type */
> +	return input_mt_init_slots(sdata->input, STMFTS_MAX_FINGERS,
> +				   INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);

Why INPUT_MT_DROP_UNUSED?

> +}
> +
> +static int stmfts_set_hover(struct stmfts_data *sdata, bool enable)
> +{
> +	return i2c_smbus_write_byte(sdata->client,
> +				    enable ? STMFTS_SS_HOVER_SENSE_ON :
> +					     STMFTS_SS_HOVER_SENSE_OFF);
> +}
> +
>  static int stmfts_enable_led(struct stmfts_data *sdata)
>  {
>  	int err;
> @@ -678,6 +1052,8 @@ static int stmfts_probe(struct i2c_client *client)
>  	mutex_init(&sdata->mutex);
>  	init_completion(&sdata->cmd_done);
>  
> +	sdata->ops = of_device_get_match_data(dev);
> +
>  	err = devm_regulator_bulk_get_const(dev,
>  					    ARRAY_SIZE(stmfts_supplies),
>  					    stmfts_supplies,
> @@ -697,8 +1073,8 @@ static int stmfts_probe(struct i2c_client *client)
>  
>  	sdata->input->name = STMFTS_DEV_NAME;
>  	sdata->input->id.bustype = BUS_I2C;
> -	sdata->input->open = stmfts_input_open;
> -	sdata->input->close = stmfts_input_close;
> +	sdata->input->open = sdata->ops->input_open;
> +	sdata->input->close = sdata->ops->input_close;
>  
>  	input_set_capability(sdata->input, EV_ABS, ABS_MT_POSITION_X);
>  	input_set_capability(sdata->input, EV_ABS, ABS_MT_POSITION_Y);
> @@ -706,19 +1082,9 @@ static int stmfts_probe(struct i2c_client *client)
>  
>  	input_set_abs_params(sdata->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
>  	input_set_abs_params(sdata->input, ABS_MT_TOUCH_MINOR, 0, 255, 0, 0);
> -	input_set_abs_params(sdata->input, ABS_MT_ORIENTATION, 0, 255, 0, 0);
>  	input_set_abs_params(sdata->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
> -	input_set_abs_params(sdata->input, ABS_DISTANCE, 0, 255, 0, 0);
> -
> -	sdata->use_key = device_property_read_bool(dev,
> -						   "touch-key-connected");
> -	if (sdata->use_key) {
> -		input_set_capability(sdata->input, EV_KEY, KEY_MENU);
> -		input_set_capability(sdata->input, EV_KEY, KEY_BACK);
> -	}
>  
> -	err = input_mt_init_slots(sdata->input,
> -				  STMFTS_MAX_FINGERS, INPUT_MT_DIRECT);
> +	err = sdata->ops->setup_input(sdata);
>  	if (err)
>  		return err;
>  
> @@ -789,13 +1155,62 @@ static int stmfts_runtime_suspend(struct device *dev)
>  	return ret;
>  }
>  
> -static int stmfts_runtime_resume(struct device *dev)
> +static int stmfts_chip_runtime_resume(struct stmfts_data *sdata)
> +{
> +	return i2c_smbus_write_byte(sdata->client, STMFTS_SLEEP_OUT);
> +}
> +
> +static int stmfts5_chip_runtime_resume(struct stmfts_data *sdata)
>  {
> -	struct stmfts_data *sdata = dev_get_drvdata(dev);
>  	struct i2c_client *client = sdata->client;
> +	struct device *dev = &client->dev;
> +	u8 int_enable_cmd[4] = {0xB6, 0x00, 0x2C, 0x01};
> +	struct i2c_msg msg = {
> +		.addr = client->addr,
> +		.len = sizeof(int_enable_cmd),
> +		.buf = int_enable_cmd,
> +	};
>  	int ret;

"int err" everywhere where the variable carries error code or 0.


Thanks.

-- 
Dmitry