[patch 21/38] hamradio: baycom_epp: Remove BAYCOM_DEBUG

The whole code guarded by BAYCOM_DEBUG is only writing debug values into a
datastructure, but there is no way to ever access them.

Remove the pointless ballast.

This is part of a larger effort to remove get_cycles() usage from
non-architecture code.

Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Thomas Sailer <[email protected]>
Cc: [email protected]
---
 drivers/net/hamradio/baycom_epp.c |   51 --------------------------------------
 1 file changed, 51 deletions(-)

--- a/drivers/net/hamradio/baycom_epp.c
+++ b/drivers/net/hamradio/baycom_epp.c
@@ -44,7 +44,6 @@
 
 /* --------------------------------------------------------------------- */
 
-#define BAYCOM_DEBUG
 #define BAYCOM_MAGIC 19730510
 
 /* --------------------------------------------------------------------- */
@@ -191,18 +190,6 @@ struct baycom_state {
 
 	unsigned int ptt_keyed;
 	struct sk_buff *skb;  /* next transmit packet  */
-
-#ifdef BAYCOM_DEBUG
-	struct debug_vals {
-		unsigned long last_jiffies;
-		unsigned cur_intcnt;
-		unsigned last_intcnt;
-		int cur_pllcorr;
-		int last_pllcorr;
-		unsigned int mod_cycles;
-		unsigned int demod_cycles;
-	} debug_vals;
-#endif /* BAYCOM_DEBUG */
 };
 
 /* --------------------------------------------------------------------- */
@@ -259,26 +246,6 @@ static inline int calc_crc_ccitt(const u
 
 #define tenms_to_flags(bc,tenms) ((tenms * bc->bitrate) / 800)
 
-/* --------------------------------------------------------------------- */
-
-static inline void baycom_int_freq(struct baycom_state *bc)
-{
-#ifdef BAYCOM_DEBUG
-	unsigned long cur_jiffies = jiffies;
-	/*
-	 * measure the interrupt frequency
-	 */
-	bc->debug_vals.cur_intcnt++;
-	if (time_after_eq(cur_jiffies, bc->debug_vals.last_jiffies + HZ)) {
-		bc->debug_vals.last_jiffies = cur_jiffies;
-		bc->debug_vals.last_intcnt = bc->debug_vals.cur_intcnt;
-		bc->debug_vals.cur_intcnt = 0;
-		bc->debug_vals.last_pllcorr = bc->debug_vals.cur_pllcorr;
-		bc->debug_vals.cur_pllcorr = 0;
-	}
-#endif /* BAYCOM_DEBUG */
-}
-
 /* ---------------------------------------------------------------------- */
 /*
  *    eppconfig_path should be setable  via /proc/sys.
@@ -621,13 +588,6 @@ static int receive(struct net_device *de
 	return ret;
 }
 
-/* --------------------------------------------------------------------- */
-
-#define GETTICK(x)						\
-({								\
-	x = (unsigned int)get_cycles();				\
-})
-
 static void epp_bh(struct work_struct *work)
 {
 	struct net_device *dev;
@@ -635,21 +595,17 @@ static void epp_bh(struct work_struct *w
 	struct parport *pp;
 	unsigned char stat;
 	unsigned char tmp[2];
-	unsigned int time1 = 0, time2 = 0, time3 = 0;
 	int cnt, cnt2;
 
 	bc = container_of(work, struct baycom_state, run_work.work);
 	dev = bc->dev;
 	if (!bc->work_running)
 		return;
-	baycom_int_freq(bc);
 	pp = bc->pdev->port;
 	/* update status */
 	if (pp->ops->epp_read_addr(pp, &stat, 1, 0) != 1)
 		goto epptimeout;
 	bc->stat = stat;
-	bc->debug_vals.last_pllcorr = stat;
-	GETTICK(time1);
 	if (bc->modem == EPP_FPGAEXTSTATUS) {
 		/* get input count */
 		tmp[0] = EPP_TX_FIFO_ENABLE|EPP_RX_FIFO_ENABLE|EPP_MODEM_ENABLE|1;
@@ -673,7 +629,6 @@ static void epp_bh(struct work_struct *w
 			goto epptimeout;
 		if (transmit(bc, cnt2, stat))
 			goto epptimeout;
-		GETTICK(time2);
 		if (receive(dev, cnt))
 			goto epptimeout;
 		if (pp->ops->epp_read_addr(pp, &stat, 1, 0) != 1)
@@ -700,7 +655,6 @@ static void epp_bh(struct work_struct *w
 		}
 		if (transmit(bc, cnt, stat))
 			goto epptimeout;
-		GETTICK(time2);
 		/* do receiver */
 		while ((stat & (EPP_NRAEF|EPP_NRHF)) != EPP_NRHF) {
 			switch (stat & (EPP_NRAEF|EPP_NRHF)) {
@@ -734,11 +688,6 @@ static void epp_bh(struct work_struct *w
 				goto epptimeout;
 		}
 	}
-	GETTICK(time3);
-#ifdef BAYCOM_DEBUG
-	bc->debug_vals.mod_cycles = time2 - time1;
-	bc->debug_vals.demod_cycles = time3 - time2;
-#endif /* BAYCOM_DEBUG */
 	schedule_delayed_work(&bc->run_work, 1);
 	if (!bc->skb)
 		netif_wake_queue(dev);