Re: [PATCH v1 1/3] hw/sd: add Kendryte K230 SDHCI controller
Bin Meng <[email protected]>
| Newsgroups | org.nongnu.qemu-devel,org.nongnu.qemu-riscv |
|---|---|
| Message-ID | <CAEUhbmXYYzy8=Sj7cBvFGLx8ArERHqHF6wtECLp_9yz+7_dm0A@mail.gmail.com> |
On Wed, Jul 29, 2026 at 7:56 PM Xin Xie <[email protected]> wrote: > > Add a minimal K230 SDHCI model based on the generic SDHCI model. Reuse > the generic commands and data paths while providing the extended register > layout and documented reset values. > > K230 SDHCI controller contains the standard SDHCI register block followed > by preset, extension pointer, PHY and vendor-specific registers. This model > implements the preset and extension pointer registers as read-only, retain > writes to most PHY and vendor-specific registers, and keep PHY_PWRGOOD > asserted so that the K230 SDK reset sequence can complete. > Please split the k230_sdhci model into 2 separate models: - One is generic Synopsys DesignWare Mobile Storage Host Controller IP model (hw/sd/dw_mshc.c) - Optional Canann K230 specific wrapper glue model to the dw_mshc IP (if the generic Synopsys DesignWare MSHC IP model, or plus some unimp region, is good enough to make the software happy, no need to create this one) > The SDHCI version is set to 3 due to the absence of ADMA3 support in the > generic model. > > Signed-off-by: Xin Xie <[email protected]> > --- > MAINTAINERS | 2 + > hw/sd/Kconfig | 4 + > hw/sd/k230_sdhci.c | 311 +++++++++++++++++++++++++++++++++++++ > hw/sd/meson.build | 1 + > include/hw/sd/k230_sdhci.h | 82 ++++++++++ > 5 files changed, 400 insertions(+) > create mode 100644 hw/sd/k230_sdhci.c > create mode 100644 include/hw/sd/k230_sdhci.h > > diff --git a/MAINTAINERS b/MAINTAINERS > index 6171cc7494..06285352c4 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1826,8 +1826,10 @@ S: Maintained > F: docs/system/riscv/k230.rst > F: hw/riscv/k230.c > F: hw/watchdog/k230_wdt.c > +F: hw/sd/k230_sdhci.c > F: include/hw/riscv/k230.h > F: include/hw/watchdog/k230_wdt.h > +F: include/hw/sd/k230_sdhci.h > F: tests/qtest/k230-wdt-test.c > > RX Machines > diff --git a/hw/sd/Kconfig b/hw/sd/Kconfig > index 633b9afec9..e9a5d63b4d 100644 > --- a/hw/sd/Kconfig > +++ b/hw/sd/Kconfig > @@ -23,3 +23,7 @@ config SDHCI_PCI > config CADENCE_SDHCI > bool > select SDHCI > + > +config K230_SDHCI > + bool > + select SDHCI > diff --git a/hw/sd/k230_sdhci.c b/hw/sd/k230_sdhci.c > new file mode 100644 > index 0000000000..34c972a2f7 > --- /dev/null > +++ b/hw/sd/k230_sdhci.c > @@ -0,0 +1,311 @@ > +/* > + * Kendryte K230 SDHCI controller > + * > + * Copyright (c) 2026 Xin Xie <[email protected]> > + * > + * SPDX-License-Identifier: GPL-2.0-or-later > + */ > + > +#include "qemu/osdep.h" > +#include "qemu/log.h" > +#include "hw/sd/k230_sdhci.h" > +#include "hw/sd/sdhci-internal.h" > +#include "migration/vmstate.h" > + > +/* > + * The TRM describes an SDHCI v4.20 DWC MSHC, including the v4 block-count > + * mode, ADMA3, and extension-area registers. QEMU's generic controller > + * supports up to v3 and does not implement those v4 transfer semantics. > + */ > +#define K230_SDHCI_SPEC_VERSION 3 > + > +/* > + * K230's Capabilities registers describe more functionality than the generic > + * QEMU SDHCI data path currently implements. Do not expose the following TRM > + * capabilities to the guest: > + * > + * - ASYNC_INT requires an SDIO card-interrupt input and asynchronous interrupt > + * signalling while the SD clock is stopped. SDBus has no such input. > + * - TIMER_RETUNING and RETUNING_MODE require a re-tuning timer and generation > + * of a re-tuning request. The generic controller only completes an initial > + * command-based tuning operation; it never schedules periodic re-tuning. > + * - ADMA3 requires the SDHCI v4.20 ADMA3 descriptor and command semantics, > + * whereas the generic controller implements SDMA and ADMA2 only. > + */ > +#define K230_SDHCI_CAPABILITIES_UNSUPPORTED \ > + (R_SDHC_CAPAB_ASYNC_INT_MASK | \ > + R_SDHC_CAPAB_TIMER_RETUNING_MASK | \ > + R_SDHC_CAPAB_RETUNING_MODE_MASK | \ > + R_SDHC_CAPAB_ADMA3_MASK) The reset value of the capability does not agree with the TRM. Please confirm the value on the real hardware, or just use the value from the TRM. > +#define K230_SDHCI_CAPAREG_IMPLEMENTED \ > + (K230_SDHCI_CAPAREG_RESET & ~K230_SDHCI_CAPABILITIES_UNSUPPORTED) > + > +#define K230_LO8(value) ((value) & 0xff) > +#define K230_HI8(value) (((value) >> 8) & 0xff) > + > +static const uint8_t k230_sdhci_preset_reset[K230_SDHCI_PRESET_SIZE] = { > + [K230_SDHCI_PRESET_INIT - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_INIT_RESET), > + [K230_SDHCI_PRESET_INIT - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_INIT_RESET), > + [K230_SDHCI_PRESET_DEFAULT_SPEED - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_DEFAULT_SPEED_RESET), > + [K230_SDHCI_PRESET_DEFAULT_SPEED - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_DEFAULT_SPEED_RESET), > + [K230_SDHCI_PRESET_HIGH_SPEED - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_HIGH_SPEED_RESET), > + [K230_SDHCI_PRESET_HIGH_SPEED - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_HIGH_SPEED_RESET), > + [K230_SDHCI_PRESET_SDR12 - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_SDR12_RESET), > + [K230_SDHCI_PRESET_SDR12 - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_SDR12_RESET), > + [K230_SDHCI_PRESET_SDR25 - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_SDR25_RESET), > + [K230_SDHCI_PRESET_SDR25 - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_SDR25_RESET), > + [K230_SDHCI_PRESET_SDR50 - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_SDR50_RESET), > + [K230_SDHCI_PRESET_SDR50 - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_SDR50_RESET), > + [K230_SDHCI_PRESET_SDR104 - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_SDR104_RESET), > + [K230_SDHCI_PRESET_SDR104 - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_SDR104_RESET), > + [K230_SDHCI_PRESET_DDR50 - K230_SDHCI_PRESET_BASE] = > + K230_LO8(K230_SDHCI_PRESET_DDR50_RESET), > + [K230_SDHCI_PRESET_DDR50 - K230_SDHCI_PRESET_BASE + 1] = > + K230_HI8(K230_SDHCI_PRESET_DDR50_RESET), > +}; > + > +static uint64_t k230_sdhci_preset_read(void *opaque, hwaddr addr, > + unsigned int size) > +{ > + return ldn_le_p(&k230_sdhci_preset_reset[addr], size); > +} > + > +static void k230_sdhci_preset_write(void *opaque, hwaddr addr, uint64_t value, > + unsigned int size) > +{ > + qemu_log_mask(LOG_GUEST_ERROR, > + "K230 SDHCI: write to read-only Preset Value register " > + "0x%03" HWADDR_PRIx "\n", > + K230_SDHCI_PRESET_BASE + addr); > +} > + > +static const MemoryRegionOps k230_sdhci_preset_ops = { > + .read = k230_sdhci_preset_read, > + .write = k230_sdhci_preset_write, > + .endianness = DEVICE_LITTLE_ENDIAN, > + .valid = { > + .min_access_size = 1, > + .max_access_size = 4, > + .unaligned = false, > + }, > +}; > + > +static const uint8_t k230_sdhci_pointer_reset[K230_SDHCI_POINTER_SIZE] = { > + [K230_SDHCI_P_UHS2_SETTINGS - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_UHS2_SETTINGS_RESET), > + [K230_SDHCI_P_UHS2_SETTINGS - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_UHS2_SETTINGS_RESET), > + [K230_SDHCI_P_UHS2_HOST_CAPAB - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_UHS2_HOST_CAPAB_RESET), > + [K230_SDHCI_P_UHS2_HOST_CAPAB - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_UHS2_HOST_CAPAB_RESET), > + [K230_SDHCI_P_UHS2_TEST - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_UHS2_TEST_RESET), > + [K230_SDHCI_P_UHS2_TEST - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_UHS2_TEST_RESET), > + [K230_SDHCI_P_EMBEDDED_CNTRL - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_EMBEDDED_CNTRL_RESET), > + [K230_SDHCI_P_EMBEDDED_CNTRL - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_EMBEDDED_CNTRL_RESET), > + [K230_SDHCI_P_VENDOR_AREA1 - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_VENDOR_AREA1_RESET), > + [K230_SDHCI_P_VENDOR_AREA1 - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_VENDOR_AREA1_RESET), > + [K230_SDHCI_P_VENDOR_AREA2 - K230_SDHCI_POINTER_BASE] = > + K230_LO8(K230_SDHCI_P_VENDOR_AREA2_RESET), > + [K230_SDHCI_P_VENDOR_AREA2 - K230_SDHCI_POINTER_BASE + 1] = > + K230_HI8(K230_SDHCI_P_VENDOR_AREA2_RESET), > +}; > + > +static uint64_t k230_sdhci_pointer_read(void *opaque, hwaddr addr, > + unsigned int size) > +{ > + return ldn_le_p(&k230_sdhci_pointer_reset[addr], size); > +} > + > +static void k230_sdhci_pointer_write(void *opaque, hwaddr addr, uint64_t value, > + unsigned int size) > +{ > + qemu_log_mask(LOG_GUEST_ERROR, > + "K230 SDHCI: write to read-only pointer register " > + "0x%03" HWADDR_PRIx "\n", > + K230_SDHCI_POINTER_BASE + addr); > +} > + > +static const MemoryRegionOps k230_sdhci_pointer_ops = { > + .read = k230_sdhci_pointer_read, > + .write = k230_sdhci_pointer_write, > + .endianness = DEVICE_LITTLE_ENDIAN, > + .valid = { > + .min_access_size = 1, > + .max_access_size = 4, > + .unaligned = false, > + }, > +}; > + > +/* > + * K230 uses the standard SDHCI register set at offset zero, followed by > + * UHS-II, DWC MSHC PHY, Embedded Control, and vendor-specific blocks. Most > + * side effects of analogue PHY behaviors not simulated. > + * > + * PHY_PWRGOOD is the sole synthesized status bit. Real hardware asserts it > + * after PHY power and reset sequencing; the SDK driver polls it during every > + * full controller reset. A virtual PHY has no settling interval or failure > + * condition, so the bit is permanently asserted and cannot be cleared by a > + * guest write. > + */ > +static uint64_t k230_sdhci_fallback_read(void *opaque, hwaddr addr, > + unsigned int size) > +{ > + K230SDHCIState *s = opaque; > + uint64_t value = ldn_le_p(&s->fallback_regs[addr], size); > + > + if (ranges_overlap(addr, size, K230_SDHCI_PHY_CNFG, > + sizeof(uint32_t)) && addr <= K230_SDHCI_PHY_CNFG) { > + unsigned int shift = (K230_SDHCI_PHY_CNFG - addr) * 8; > + > + value |= (uint64_t)K230_SDHCI_PHY_CNFG_PWRGOOD << shift; > + } > + > + return value; > +} > + > +static void k230_sdhci_fallback_write(void *opaque, hwaddr addr, > + uint64_t value, unsigned int size) > +{ > + K230SDHCIState *s = opaque; > + > + stn_le_p(&s->fallback_regs[addr], size, value); > + > + /* PWRGOOD reflects PHY state and is not software writable. */ > + s->fallback_regs[K230_SDHCI_PHY_CNFG] |= > + K230_SDHCI_PHY_CNFG_PWRGOOD; > +} > + > +static const MemoryRegionOps k230_sdhci_fallback_ops = { > + .read = k230_sdhci_fallback_read, > + .write = k230_sdhci_fallback_write, > + .endianness = DEVICE_LITTLE_ENDIAN, > + .valid = { > + .min_access_size = 1, > + .max_access_size = 4, > + .unaligned = false, > + }, > +}; > + > +static void k230_sdhci_reset(DeviceState *dev) > +{ > + K230SDHCIState *s = K230_SDHCI(dev); > + > + memset(s->fallback_regs, 0, sizeof(s->fallback_regs)); > + s->fallback_regs[K230_SDHCI_PHY_CNFG] = > + K230_SDHCI_PHY_CNFG_PWRGOOD; > + device_cold_reset(DEVICE(&s->sdhci)); > +} > + > +static void k230_sdhci_realize(DeviceState *dev, Error **errp) > +{ > + K230SDHCIState *s = K230_SDHCI(dev); > + SysBusDevice *sbd = SYS_BUS_DEVICE(dev); > + SysBusDevice *sdhci_sbd = SYS_BUS_DEVICE(&s->sdhci); > + > + memory_region_init(&s->container, OBJECT(s), "k230.sdhci-container", > + K230_SDHCI_REG_SIZE); > + sysbus_init_mmio(sbd, &s->container); > + > + memory_region_init_io(&s->iomem_fallback, OBJECT(s), > + &k230_sdhci_fallback_ops, s, > + "k230.sdhci-fallback", > + K230_SDHCI_REG_SIZE); > + memory_region_add_subregion(&s->container, 0, &s->iomem_fallback); > + > + if (!sysbus_realize(sdhci_sbd, errp)) { > + return; > + } > + memory_region_add_subregion_overlap( > + &s->container, 0, sysbus_mmio_get_region(sdhci_sbd, 0), 1); > + > + memory_region_init_io(&s->iomem_preset, OBJECT(s), > + &k230_sdhci_preset_ops, s, > + "k230.sdhci-preset", K230_SDHCI_PRESET_SIZE); > + memory_region_add_subregion_overlap(&s->container, > + K230_SDHCI_PRESET_BASE, > + &s->iomem_preset, 2); > + > + memory_region_init_io(&s->iomem_pointer, OBJECT(s), > + &k230_sdhci_pointer_ops, s, > + "k230.sdhci-pointers", K230_SDHCI_POINTER_SIZE); > + memory_region_add_subregion_overlap(&s->container, > + K230_SDHCI_POINTER_BASE, > + &s->iomem_pointer, 2); > + > + sysbus_pass_irq(sbd, sdhci_sbd); > + s->bus = qdev_get_child_bus(DEVICE(sdhci_sbd), "sd-bus"); > +} > + > +static const VMStateDescription vmstate_k230_sdhci = { > + .name = TYPE_K230_SDHCI, > + .version_id = 1, > + .minimum_version_id = 1, > + .fields = (const VMStateField[]) { > + VMSTATE_UINT8_ARRAY(fallback_regs, K230SDHCIState, > + K230_SDHCI_REG_SIZE), > + VMSTATE_END_OF_LIST() > + }, > +}; > + > +static void k230_sdhci_instance_init(Object *obj) > +{ > + K230SDHCIState *s = K230_SDHCI(obj); > + > + object_initialize_child(obj, "generic-sdhci", &s->sdhci, > + TYPE_SYSBUS_SDHCI); > + > + object_property_set_uint(OBJECT(&s->sdhci), "sd-spec-version", > + K230_SDHCI_SPEC_VERSION, > + &error_abort); > + object_property_set_uint(OBJECT(&s->sdhci), "capareg", > + K230_SDHCI_CAPAREG_IMPLEMENTED, > + &error_abort); > + object_property_set_uint(OBJECT(&s->sdhci), "uhs", UHS_I, &error_abort); > +} > + > +static void k230_sdhci_class_init(ObjectClass *klass, const void *data) > +{ > + DeviceClass *dc = DEVICE_CLASS(klass); > + > + dc->desc = "Kendryte K230 SDHCI Controller"; > + dc->realize = k230_sdhci_realize; > + device_class_set_legacy_reset(dc, k230_sdhci_reset); > + dc->vmsd = &vmstate_k230_sdhci; > + set_bit(DEVICE_CATEGORY_STORAGE, dc->categories); > +} > + > +static const TypeInfo k230_sdhci_type_info = { > + .name = TYPE_K230_SDHCI, > + .parent = TYPE_SYS_BUS_DEVICE, > + .instance_size = sizeof(K230SDHCIState), > + .instance_init = k230_sdhci_instance_init, > + .class_init = k230_sdhci_class_init, > +}; > + > +static void k230_sdhci_register_types(void) > +{ > + type_register_static(&k230_sdhci_type_info); > +} > + > +type_init(k230_sdhci_register_types) > diff --git a/hw/sd/meson.build b/hw/sd/meson.build > index b43d45bc56..a109635233 100644 > --- a/hw/sd/meson.build > +++ b/hw/sd/meson.build > @@ -10,3 +10,4 @@ system_ss.add(when: 'CONFIG_ASPEED_SOC', if_true: files('aspeed_sdhci.c')) > system_ss.add(when: 'CONFIG_ALLWINNER_H3', if_true: files('allwinner-sdhost.c')) > system_ss.add(when: 'CONFIG_NPCM7XX', if_true: files('npcm7xx_sdhci.c')) > system_ss.add(when: 'CONFIG_CADENCE_SDHCI', if_true: files('cadence_sdhci.c')) > +system_ss.add(when: 'CONFIG_K230_SDHCI', if_true: files('k230_sdhci.c')) > diff --git a/include/hw/sd/k230_sdhci.h b/include/hw/sd/k230_sdhci.h > new file mode 100644 > index 0000000000..a8389f1de4 > --- /dev/null > +++ b/include/hw/sd/k230_sdhci.h > @@ -0,0 +1,82 @@ > +/* > + * Kendryte K230 SDHCI controller > + * > + * Copyright (c) 2026 Xin Xie <[email protected]> > + * > + * SPDX-License-Identifier: GPL-2.0-or-later > + */ > + > +#ifndef HW_SD_K230_SDHCI_H > +#define HW_SD_K230_SDHCI_H > + > +#include "qemu/bitops.h" > +#include "hw/sd/sdhci.h" > +#include "qom/object.h" > + > +#define TYPE_K230_SDHCI "k230.sdhci" > +OBJECT_DECLARE_SIMPLE_TYPE(K230SDHCIState, K230_SDHCI) > + > +#define K230_SDHCI_REG_SIZE 0x1000 > + > +/* K230 TRM reset values for Capabilities Registers 1 and 2. */ > +#define K230_SDHCI_CAPABILITIES1_RESET 0x256ec881ULL > +#define K230_SDHCI_CAPABILITIES2_RESET 0x0800a177ULL > +#define K230_SDHCI_CAPAREG_RESET \ > + ((K230_SDHCI_CAPABILITIES2_RESET << 32) \ > + | K230_SDHCI_CAPABILITIES1_RESET) > + > +/* SDHCI Preset Value registers. */ > +#define K230_SDHCI_PRESET_BASE 0x060 > +#define K230_SDHCI_PRESET_SIZE 0x010 > +#define K230_SDHCI_PRESET_INIT 0x060 > +#define K230_SDHCI_PRESET_DEFAULT_SPEED 0x062 > +#define K230_SDHCI_PRESET_HIGH_SPEED 0x064 > +#define K230_SDHCI_PRESET_SDR12 0x066 > +#define K230_SDHCI_PRESET_SDR25 0x068 > +#define K230_SDHCI_PRESET_SDR50 0x06a > +#define K230_SDHCI_PRESET_SDR104 0x06c > +#define K230_SDHCI_PRESET_DDR50 0x06e > +#define K230_SDHCI_PRESET_INIT_RESET 0x00fa > +#define K230_SDHCI_PRESET_DEFAULT_SPEED_RESET 0x0004 > +#define K230_SDHCI_PRESET_HIGH_SPEED_RESET 0x0002 > +#define K230_SDHCI_PRESET_SDR12_RESET 0x0004 > +#define K230_SDHCI_PRESET_SDR25_RESET 0x0002 > +#define K230_SDHCI_PRESET_SDR50_RESET 0x0001 > +#define K230_SDHCI_PRESET_SDR104_RESET 0x0000 > +#define K230_SDHCI_PRESET_DDR50_RESET 0x0002 > + > +/* SDHCI v4 extension-area pointer registers. */ > +#define K230_SDHCI_POINTER_BASE 0x0e0 > +#define K230_SDHCI_POINTER_SIZE 0x00c > +#define K230_SDHCI_P_UHS2_SETTINGS 0x0e0 > +#define K230_SDHCI_P_UHS2_HOST_CAPAB 0x0e2 > +#define K230_SDHCI_P_UHS2_TEST 0x0e4 > +#define K230_SDHCI_P_EMBEDDED_CNTRL 0x0e6 > +#define K230_SDHCI_P_VENDOR_AREA1 0x0e8 > +#define K230_SDHCI_P_VENDOR_AREA2 0x0ea > +#define K230_SDHCI_P_UHS2_SETTINGS_RESET 0x0000 > +#define K230_SDHCI_P_UHS2_HOST_CAPAB_RESET 0x0f58 > +#define K230_SDHCI_P_UHS2_TEST_RESET 0x0f68 > +#define K230_SDHCI_P_EMBEDDED_CNTRL_RESET 0x0f6c > +#define K230_SDHCI_P_VENDOR_AREA1_RESET 0x0500 > +#define K230_SDHCI_P_VENDOR_AREA2_RESET 0x0384 > + > +/* DWC MSHC PHY register block. */ nits: remove the ending period. Please fix this globally in this patch series. > +#define K230_SDHCI_PHY_CNFG 0x300 > +#define K230_SDHCI_PHY_CNFG_RSTN BIT(0) > +#define K230_SDHCI_PHY_CNFG_PWRGOOD BIT(1) > + > +struct K230SDHCIState { > + SysBusDevice parent_obj; > + > + MemoryRegion container; > + MemoryRegion iomem_fallback; > + MemoryRegion iomem_preset; > + MemoryRegion iomem_pointer; > + BusState *bus; > + uint8_t fallback_regs[K230_SDHCI_REG_SIZE]; > + > + SDHCIState sdhci; > +}; > + > +#endif Regards, Bin