[PATCH] ARM: dts: aspeed: Correct indentation
Krzysztof Kozlowski <[email protected]> Mon, 6 Jul 2026 12:19:31 +0200
| Newsgroups | org.ozlabs.lists.linux-aspeed,org.infradead.lists.linux-arm-kernel,org.kernel.vger.linux-devicetree,org.kernel.vger.linux-kernel |
|---|---|
| Message-ID | <[email protected]> |
Correct spaces or mix of tabs+spaces into proper tab-indented lines. No functional impact (same DTB). Signed-off-by: Krzysztof Kozlowski <[email protected]> --- Ongoing bigger work for all bindings and DTS with built-in checker (dt-check-style). --- .../aspeed-bmc-inventec-transformers.dts | 200 +++++++++--------- .../boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts | 2 +- arch/arm/boot/dts/aspeed/aspeed-g6.dtsi | 2 +- 3 files changed, 102 insertions(+), 102 deletions(-) diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts index c713cb7a6187..e51c726b4a55 100644 --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts @@ -13,33 +13,33 @@ / { compatible = "inventec,transformer-bmc", "aspeed,ast2600"; aliases { - serial4 = &uart5; + serial4 = &uart5; }; chosen { - stdout-path = &uart5; - bootargs = "console=ttyS4,115200n8"; + stdout-path = &uart5; + bootargs = "console=ttyS4,115200n8"; }; memory@80000000 { - device_type = "memory"; - reg = <0x80000000 0x80000000>; + device_type = "memory"; + reg = <0x80000000 0x80000000>; }; leds { - compatible = "gpio-leds"; + compatible = "gpio-leds"; - // UID led - uid { - label = "UID_LED"; - gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; - }; + // UID led + uid { + label = "UID_LED"; + gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; + }; - // Heart beat led - heartbeat { - label = "HB_LED"; - gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; - }; + // Heart beat led + heartbeat { + label = "HB_LED"; + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; + }; }; }; @@ -47,8 +47,8 @@ &mdio0 { status = "okay"; ethphy0: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; }; }; @@ -64,22 +64,22 @@ &fmc { status = "okay"; flash@0 { - status = "okay"; - m25p,fast-read; - label = "bmc"; - spi-max-frequency = <33000000>; - spi-tx-bus-width = <2>; - spi-rx-bus-width = <2>; + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; #include "openbmc-flash-layout.dtsi" }; flash@1 { - status = "okay"; - m25p,fast-read; - label = "bmc2"; - spi-max-frequency = <33000000>; - spi-tx-bus-width = <2>; - spi-rx-bus-width = <2>; + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; }; }; @@ -89,12 +89,12 @@ &spi1 { pinctrl-0 = <&pinctrl_spi1_default>; flash@0 { - status = "okay"; - m25p,fast-read; - label = "bios"; - spi-max-frequency = <33000000>; - spi-tx-bus-width = <1>; - spi-rx-bus-width = <1>; + status = "okay"; + m25p,fast-read; + label = "bios"; + spi-max-frequency = <33000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <1>; }; }; @@ -115,9 +115,9 @@ &i2c0 { //Set bmc' slave address; bmc_slave@10 { - compatible = "ipmb-dev"; - reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; - i2c-protocol; + compatible = "ipmb-dev"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + i2c-protocol; }; }; @@ -129,9 +129,9 @@ &i2c3 { // FRU AT24C512C-SSHM-T status = "okay"; eeprom@50 { - compatible = "atmel,24c512"; - reg = <0x50>; - pagesize = <128>; + compatible = "atmel,24c512"; + reg = <0x50>; + pagesize = <128>; }; }; @@ -143,26 +143,26 @@ &i2c6 { status = "okay"; tmp75@49 { - compatible = "ti,tmp75"; - reg = <0x49>; + compatible = "ti,tmp75"; + reg = <0x49>; }; tmp75@4f { - compatible = "ti,tmp75"; - reg = <0x4f>; + compatible = "ti,tmp75"; + reg = <0x4f>; }; tmp468@48 { - compatible = "ti,tmp468"; - reg = <0x48>; + compatible = "ti,tmp468"; + reg = <0x48>; }; }; &i2c7 { status = "okay"; adm1278@40 { - compatible = "adi,adm1278"; - reg = <0x40>; + compatible = "adi,adm1278"; + reg = <0x40>; }; }; @@ -172,15 +172,15 @@ &i2c8 { status = "okay"; eeprom@51 { - compatible = "atmel,24c512"; - reg = <0x51>; - pagesize = <128>; + compatible = "atmel,24c512"; + reg = <0x51>; + pagesize = <128>; }; eeprom@53 { - compatible = "atmel,24c512"; - reg = <0x53>; - pagesize = <128>; + compatible = "atmel,24c512"; + reg = <0x53>; + pagesize = <128>; }; }; @@ -194,17 +194,17 @@ &i2c10 { status = "okay"; i2c-mux@71 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x71>; + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; }; i2c-mux@73 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x73>; + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x73>; }; }; @@ -213,46 +213,46 @@ &i2c11 { status = "okay"; i2c-mux@70 { - compatible = "nxp,pca9544"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x70>; + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; - pcie_eeprom_riser1: i2c@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; + pcie_eeprom_riser1: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; - eeprom@55 { - compatible = "atmel,24c512"; - reg = <0x55>; - pagesize = <128>; - }; - }; + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; - pcie_eeprom_riser2: i2c@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; + pcie_eeprom_riser2: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; - eeprom@55 { - compatible = "atmel,24c512"; - reg = <0x55>; - pagesize = <128>; - }; - }; + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; - pcie_eeprom_riser3: i2c@2 { - #address-cells = <1>; - #size-cells = <0>; - reg = <2>; + pcie_eeprom_riser3: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; - eeprom@55 { - compatible = "atmel,24c512"; - reg = <0x55>; - pagesize = <128>; - }; - }; + eeprom@55 { + compatible = "atmel,24c512"; + reg = <0x55>; + pagesize = <128>; + }; + }; }; }; @@ -260,8 +260,8 @@ &i2c12 { status = "okay"; psu0:psu0@58 { - compatible = "pmbus"; - reg = <0x58>; + compatible = "pmbus"; + reg = <0x58>; }; }; diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts index 8a7fb55ab489..5a3e8a3941d4 100644 --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts @@ -82,7 +82,7 @@ &fmc { flash@0 { status = "okay"; m25p,fast-read; - label = "bmc"; + label = "bmc"; #include "openbmc-flash-layout.dtsi" }; diff --git a/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi index 56bb3b0444f7..edf4b74f5aba 100644 --- a/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi +++ b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi @@ -517,7 +517,7 @@ timer: timer@1e782000 { clocks = <&syscon ASPEED_CLK_APB1>; clock-names = "PCLK"; status = "disabled"; - }; + }; uart1: serial@1e783000 { compatible = "ns16550a"; -- 2.53.0