[PATCH v5 08/21] board: mach-k3: r5: common: enable GTC after core_resume
"Richard Genoud (TI)" <[email protected]>
| Newsgroups | org.u-boot-project.lists.u-boot |
|---|---|
| Message-ID | <[email protected]> |
From: Abhash Kumar Jha <[email protected]> The GTC counter values are restored in the resume sequence by TIFS as part of the core_resume API. Enable GTC counter after it is restored. Also add a check to make sure that rproc_load only enables the GTC counter in the case of a cold boot. Signed-off-by: Abhash Kumar Jha <[email protected]> Co-developed-by: Richard Genoud (TI) <[email protected]> Signed-off-by: Richard Genoud (TI) <[email protected]> --- arch/arm/mach-k3/r5/lpm-common.c | 11 +++++++++++ drivers/remoteproc/ti_k3_arm64_rproc.c | 10 ++++++++-- 2 files changed, 19 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-k3/r5/lpm-common.c b/arch/arm/mach-k3/r5/lpm-common.c index ab39ea0cd67d..4f515b51fd40 100644 --- a/arch/arm/mach-k3/r5/lpm-common.c +++ b/arch/arm/mach-k3/r5/lpm-common.c @@ -311,6 +311,7 @@ static void resume_rproc_f(void) { struct power_domain rproc_pwrdmn; struct udevice *dev; + void *gtc_base; int ret; ret = uclass_get_device_by_seq(UCLASS_REMOTEPROC, 1, &dev); @@ -321,6 +322,16 @@ static void resume_rproc_f(void) if (ret) panic("power_domain_get_rproc() failed: %d\n", ret); + gtc_base = dev_read_addr_ptr(dev); + if (!gtc_base) + panic("Get GTC address failed\n"); + +#define GTC_CNTCR_REG 0x0 +#define GTC_CNTR_EN 0x3 + + /* GTC counter values have been restored by TIFS, so enable the counter */ + writel(GTC_CNTR_EN, gtc_base + GTC_CNTCR_REG); + ret = power_domain_on(&rproc_pwrdmn); if (ret) panic("power_domain_on failed: %d\n", ret); diff --git a/drivers/remoteproc/ti_k3_arm64_rproc.c b/drivers/remoteproc/ti_k3_arm64_rproc.c index 403c6bed2e8c..9b8a6b7dc53a 100644 --- a/drivers/remoteproc/ti_k3_arm64_rproc.c +++ b/drivers/remoteproc/ti_k3_arm64_rproc.c @@ -17,6 +17,7 @@ #include <dm/device_compat.h> #include <linux/err.h> #include <linux/soc/ti/ti_sci_protocol.h> +#include <mach/hardware.h> #include "ti_sci_proc.h" #define INVALID_ID 0xff @@ -78,8 +79,13 @@ static int k3_arm64_load(struct udevice *dev, ulong addr, ulong size) /* Store the clock frequency down for GTC users to pick up */ writel((u32)gtc_rate, rproc->gtc_base + GTC_CNTFID0_REG); - /* Enable the timer before starting remote core */ - writel(GTC_CNTR_EN, rproc->gtc_base + GTC_CNTCR_REG); + if (!j7xx_board_is_resuming()) { + /* + * In case of a fresh boot, enable the timer before + * starting the remote core. + */ + writel(GTC_CNTR_EN, rproc->gtc_base + GTC_CNTCR_REG); + } /* * Setting the right clock frequency would have taken care by