Re: setting INTERACTIVITY back to "not set"?
Nathan Stratton Treadway <[email protected]> Tue, 14 Nov 2017 18:01:07 -0500
| Newsgroups | gmane.comp.archivers.amanda.devel |
|---|---|
| Message-ID | <[email protected]> |
On Tue, Nov 14, 2017 at 12:59:42 -0500, Jean-Louis Martineau wrote:
> Nathan,
>
> Can you try the attached patch?
Yep, with the patch applied, I can successfully override to "not set" on
the command line (both the global setting and per-storage):
=====
# su backup -lc 'amadmin TestBackup config' | egrep "^[[:space:]]*INTERACT|DEFINE STORAGE"
INTERACTIVITY "inter_tty_email"
DEFINE STORAGE TestBackup {
INTERACTIVITY "inter_tty_email"
DEFINE STORAGE TestOffsite {
INTERACTIVITY "inter_tty"
# su backup -lc 'amadmin TestBackup config -ointeractivity=' | egrep "^[[:space:]]*INTERACT|DEFINE STORAGE"
INTERACTIVITY ""
DEFINE STORAGE TestBackup {
INTERACTIVITY ""
DEFINE STORAGE TestOffsite {
INTERACTIVITY "inter_tty"
# su backup -c 'amcheck -s TestBackup -ostorage=TestOffsite'
Amanda Tape Server Host Check
-----------------------------
NOTE: Holding disk '/amanda/TestBackup-holding': 413192 MB disk space available, using 412992 MB
ERROR: Failed to open /dev/tty: No such device or address
Server check took 0.126 seconds
(brought to you by Amanda 3.5)
# su backup -c 'amcheck -s TestBackup -ostorage=TestOffsite -ostorage:TestOffsite:interactivity='
Amanda Tape Server Host Check
-----------------------------
NOTE: Holding disk '/amanda/TestBackup-holding': 413192 MB disk space available, using 412992 MB
ERROR: No acceptable volumes found
Server check took 0.137 seconds
(brought to you by Amanda 3.5)
=====
... and also in the amanda.conf storage definition:
=====
# egrep -i "^[[:space:]]*INTERACT|DEFINE STORAGE" /etc/amanda/TestBackup/amanda.conf
interactivity "inter_tty_email"
define storage TestBackup {
define storage TestOffsite {
interactivity ""
# su backup -lc 'amadmin TestBackup config' | egrep "^[[:space:]]*INTERACT|DEFINE STORAGE"
INTERACTIVITY "inter_tty_email"
DEFINE STORAGE TestBackup {
INTERACTIVITY "inter_tty_email"
DEFINE STORAGE TestOffsite {
INTERACTIVITY ""
=====
However, in my testing I noticed that amgetconf treats a blank
interactivity as "no such parameter". I don't remember off-hand
how that worked before applying the patch, but it is different from
other options:
=====
# su backup -lc 'amadmin TestBackup config' | egrep -A1
"^[[:space:]]*INTERACT|DEFINE STORAGE"
INTERACTIVITY "inter_tty_email"
TAPERSCAN "taper_lexical"
--
DEFINE STORAGE TestBackup {
COMMENT ""
--
INTERACTIVITY "inter_tty_email"
SET-NO-REUSE no
--
DEFINE STORAGE TestOffsite {
COMMENT ""
--
INTERACTIVITY ""
SET-NO-REUSE no
# amgetconf TestBackup storage:TestOffsite:comment
# amgetconf TestBackup storage:TestOffsite:interactivity
amgetconf: no such parameter "storage:TestOffsite:interactivity"
=====
Similarly for the global parameter (i.e. if I comment out all
"interactivity" lines from my amanda.conf):
=====
~# su backup -lc 'amadmin TestBackup config' | egrep "^PRINTER|^INTERACTIVITY"
PRINTER ""
INTERACTIVITY ""
# amgetconf TestBackup printer
# amgetconf TestBackup interactivity
amgetconf: no such parameter "interactivity"
=====
(Looks like amgetconf also gives "no such parameter" error for
unset/empty taperscan and policy:
=====
# amgetconf TestBackup taperscan
taper_lexical
# amgetconf TestBackup taperscan -otaperscan=
amgetconf: no such parameter "taperscan"
# amgetconf TestBackup storage:TestBackup:policy
TestBackup
# amgetconf TestBackup storage:TestBackup:policy -ostorage:TestBackup:policy=
amgetconf: no such parameter "storage:TestBackup:policy"
=====
)
Nathan
----------------------------------------------------------------------------
Nathan Stratton Treadway - [email protected] - Mid-Atlantic region
Ray Ontko & Co. - Software consulting services - http://www.ontko.com/
GPG Key: http://www.ontko.com/~nathanst/gpg_key.txt ID: 1023D/ECFB6239
Key fingerprint = 6AD8 485E 20B9 5C71 231C 0C32 15F3 ADCD ECFB 6239