Re: lost interupt

Hi,
back again,
Well I have VIA chipset 
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
00:0b.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 
64/Model 64 Pro] (rev 15)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus 
Master IDE (rev 06)

Also, I have my cdrom and cdrw on hdc and hdd (In case I didn't metion it 
before) and scsi emulated to

scsibus1:
        1,0,0   100) 'TEAC    ' 'CD-532E-B       ' '3.0B' Removable CD-ROM
        1,1,0   101) 'TEAC    ' 'CD-W58E         ' '1.0A' Removable CD-ROM


Is there something I can do for getting more info from kernel error/debug 
output; more than 'lost interupt'?

regards, himba

Dne četrtek 5. junija 2003 20:20 je Ian Pilcher napisal(a):
> Bill Davidsen wrote:
> > What has this to do with the question asked? He didn't mention VIA, and I
> > have had no particular problems with VIA, SiS or Intel chipsets, all of
> > which work on decent motherboards. And an incompetent vendor can mess up
> > any chipset.
>
> This can happen with some VIA chipsets, but I don't think that anyone's
> ever figured out if the problem lies in the Northbridge (PCI timings or
> somesuch) or the Southbridge (IDE controller).
>
> It also seems to be dependent on the exact configuration of IDE devices.
> For example, I would get these errors when trying to rip audio tracks
> from hda or hdc in the following configuration:
>
>      VIA VT82C686B:      ide0:   hda:    Creative 52X CD-ROM
>                                  hdb:    (none)
>
>                          ide1:   hdc:    CyberDrv CD-R/RW
>                                  hdd:    (none)
>
>      Promise PDC20269:   ide2:   hde:    Maxtor 30GB HDD
>                                  hdf:    (none)
>
>                          ide3:   hdg:    Western Digital 120GB HDD
>                                  hdh:    (none)
>
>      Promise PDC20269:   ide4:   hdi:    Maxtor 120GB HDD
>                                  hdj:    (none)
>
>                          ide5:   hdk:    Maxtor 120GB HDD
>                                  hdl:    (none)
>
> With the following configuration, however, I can rip from hdc or hdd
> with no problem:
>
>      VIA VT82C686B:      ide0:   hda:    Maxtor 30GB HDD
>                                  hdb:    (none)
>
>                          ide1:   hdc:    CyberDrv CD-R/RW
>                                  hdd:    Creative 52X CD-ROM
>
>      Promise PDC20269:   ide2:   hde:    Western Digital 180GB HDD
>                                  hdf:    (none)
>
>                          ide3:   hdg:    Western Digital 120GB HDD
>                                  hdh:    (none)
>
>      Promise PDC20269:   ide4:   hdi:    Maxtor 120GB HDD
>                                  hdj:    (none)
>
>                          ide5:   hdk:    Maxtor 120GB HDD
>                                  hdl:    (none)
>
> <sarcasm>
> Of course, I'm using Red Hat, which packages cdparanoia as an RPM, so
> I'm sure that's the cause of all this.
> </sarcasm>

-- 
This €-mail was Kmailed.
--- >8 ----
List archives:  http://www.xiph.org/archives/
Paranoia homepage: http://www.xiph.org/paranoia/
To unsubscribe from this list, send a message to '[email protected]'
containing only the word 'unsubscribe' in the body.  No subject is needed.
Unsubscribe messages sent to the list will be ignored/filtered.