Re: lost interupt

I am sorry for the bad haiku that I sent in response earlier. Poor attempt at humor. 

Your symptoms sound a lot like a problem some people are having ripping audio from some CD-ROMS, in a system using a VIA IDE controller. If it's the same problem, I can tell you that this has been around for a while, and your best bet may be to try swapping out hardware. It's not a simple problem, and some CD-ROMS may work and not others. Try a different brand CD-ROM drive (e.g. Lite-On), or try an Intel based board. 

-Ted

On Thu, 5 Jun 2003 23:22:53 +0200
himbA <[email protected]> wrote:

> Hi,
> back again,
> Well I have VIA chipset 
> 00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
> 00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
> 00:0b.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 
> 64/Model 64 Pro] (rev 15)
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
> 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus 
> Master IDE (rev 06)
> 
> Also, I have my cdrom and cdrw on hdc and hdd (In case I didn't metion it 
> before) and scsi emulated to
> 
> scsibus1:
>         1,0,0   100) 'TEAC    ' 'CD-532E-B       ' '3.0B' Removable CD-ROM
>         1,1,0   101) 'TEAC    ' 'CD-W58E         ' '1.0A' Removable CD-ROM
> 
> 
> Is there something I can do for getting more info from kernel error/debug 
> output; more than 'lost interupt'?
> 
> regards, himba
> 
> Dne četrtek 5. junija 2003 20:20 je Ian Pilcher napisal(a):
> > Bill Davidsen wrote:
> > > What has this to do with the question asked? He didn't mention VIA, and I
> > > have had no particular problems with VIA, SiS or Intel chipsets, all of
> > > which work on decent motherboards. And an incompetent vendor can mess up
> > > any chipset.
> >
> > This can happen with some VIA chipsets, but I don't think that anyone's
> > ever figured out if the problem lies in the Northbridge (PCI timings or
> > somesuch) or the Southbridge (IDE controller).
> >
> > It also seems to be dependent on the exact configuration of IDE devices.
> > For example, I would get these errors when trying to rip audio tracks
> > from hda or hdc in the following configuration:
> >
> >      VIA VT82C686B:      ide0:   hda:    Creative 52X CD-ROM
> >                                  hdb:    (none)
> >
> >                          ide1:   hdc:    CyberDrv CD-R/RW
> >                                  hdd:    (none)
> >
> >      Promise PDC20269:   ide2:   hde:    Maxtor 30GB HDD
> >                                  hdf:    (none)
> >
> >                          ide3:   hdg:    Western Digital 120GB HDD
> >                                  hdh:    (none)
> >
> >      Promise PDC20269:   ide4:   hdi:    Maxtor 120GB HDD
> >                                  hdj:    (none)
> >
> >                          ide5:   hdk:    Maxtor 120GB HDD
> >                                  hdl:    (none)
> >
> > With the following configuration, however, I can rip from hdc or hdd
> > with no problem:
> >
> >      VIA VT82C686B:      ide0:   hda:    Maxtor 30GB HDD
> >                                  hdb:    (none)
> >
> >                          ide1:   hdc:    CyberDrv CD-R/RW
> >                                  hdd:    Creative 52X CD-ROM
> >
> >      Promise PDC20269:   ide2:   hde:    Western Digital 180GB HDD
> >                                  hdf:    (none)
> >
> >                          ide3:   hdg:    Western Digital 120GB HDD
> >                                  hdh:    (none)
> >
> >      Promise PDC20269:   ide4:   hdi:    Maxtor 120GB HDD
> >                                  hdj:    (none)
> >
> >                          ide5:   hdk:    Maxtor 120GB HDD
> >                                  hdl:    (none)
> >
> > <sarcasm>
> > Of course, I'm using Red Hat, which packages cdparanoia as an RPM, so
> > I'm sure that's the cause of all this.
> > </sarcasm>
> 
> -- 
> This €-mail was Kmailed.
> --- >8 ----
> List archives:  http://www.xiph.org/archives/
> Paranoia homepage: http://www.xiph.org/paranoia/
> To unsubscribe from this list, send a message to '[email protected]'
> containing only the word 'unsubscribe' in the body.  No subject is needed.
> Unsubscribe messages sent to the list will be ignored/filtered.
--- >8 ----
List archives:  http://www.xiph.org/archives/
Paranoia homepage: http://www.xiph.org/paranoia/
To unsubscribe from this list, send a message to '[email protected]'
containing only the word 'unsubscribe' in the body.  No subject is needed.
Unsubscribe messages sent to the list will be ignored/filtered.