Is Q DISK supposed to look like this?
Mike Voss <[email protected]>
| Newsgroups | gmane.comp.emulators.hercules390.vm |
|---|---|
| Message-ID | <[email protected]> |
This may be why I can't find DMKRIO ASSEMBLE. Disks D thru G aren't supposed to be empty, are they? q disk Label CUU M Stat Cyl Type Blksize Files Blks Used-(%) Blks Left Blk Total CMS191 191 A R/W 115 3350 800 8 23-00 65508 65531 CMS192 192 D R/W 115 3350 800 0 5-00 65526 65531 CMS193 193 E R/W 115 3350 800 0 15-00 65516 65531 CMS194 194 F R/W 115 3350 800 0 5-00 65526 65531 CMS195 195 G R/W 94 3350 800 0 5-00 53575 53580 CMSDSK 190 S R/O 59 3350 800 160 18037-54 15593 33630 MNT19D 19D U/S R/O 70 3350 800 348 4623-12 35277 39900 MNT19E 19E Y/S R/O 70 3350 800 630 20117-50 19783 39900 Ready; T=0.01/0.01 23:06:50 q cplevel SYSTEM 4381-A VM/370 Release 06 Hercules "SixPack" version 1.2: 07/14/10 11:38:11 Ready; T=0.01/0.01 23:11:29 Mike V --- On Wed, 8/11/10, Dave Wade <g4ugm-/rAkYNWUBEC+PENguQupYdBc4/[email protected]> wrote: From: Dave Wade <g4ugm-/rAkYNWUBEC+PENguQupYdBc4/[email protected]> Subject: RE: [H390-VM] Re: Sixpack 1.2: how to log in two users? To: [email protected] Date: Wednesday, August 11, 2010, 5:49 PM I don't have the six pack but I get get 2 x model 2 and 2 x model 4 devices connected on the five pack... Dave Wade G4UGM Illegitimi Non Carborundum > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Fran Hensler > Sent: 11 August 2010 22:16 > To: [email protected] > Subject: Re: [H390-VM] Re: Sixpack 1.2: how to log in two users? > > > Bob - > > I have not installed the 1.2 beta SixPack. > > I have in DMKRIO: > RDEVICE ADDRESS=(2C0,7),DEVTYPE=3278,MODEL=4 > and my SixPack.conf has: > > # Console Printers > > 0009 3215-C NOPROMPT > 000A 1052 NOPROMPT > > # Display Terminals > > 02C0 3270 > 02C1 3270 > 02C2 3270 > 02C3 3270 > 02C4 3270 > > When I do a CP Q 2C0-2C7 I get: > GRAF 2C0 LOGON AS MAINT > GRAF 2C1 ENABLED > GRAF 2C2 ENABLED > GRAF 2C3 ENABLED > GRAF 2C4 ENABLED > GRAF 2C5 OFFLINE > GRAF 2C6 OFFLINE > GRAF 2C7 OFFLINE > > The 5 terminals I have in the conf file were all ENAbled when > VM came up. > > I can connect to all 5 enabled terminals. > > I have no Model-2 terminals in my CONF. > Perhaps that is the key. > > /Fran Hensler at Slippery Rock University of Pennsylvania USA > for 47 years > mailto:[email protected] http://zvm.sru.edu/~fjh +1.724.738.2153 > "Yes, Virginia, there is a Slippery Rock" > ---------------------------------------------------------- > ------------ > > On Wed, 11 Aug 2010 05:48:50 -0000 Robert O'Hara said: > >Mike, > > > >Well, you have just exposed me as a noob regarding DMKRIO, > which is the > >file that defines CP's I/O configuration. The VM Sixpack DMKRIO > >ASSEMBLE is on MAINT 94, and has the following lines for > terminals and > >their controllers: > > > >RCTLUNIT ADDRESS=018,CUTYPE=3215 > > RDEVICE ADDRESS=004,DEVTYPE=3215 > > RDEVICE ADDRESS=005,DEVTYPE=3215 > > RDEVICE ADDRESS=006,DEVTYPE=3215 > > RDEVICE ADDRESS=007,DEVTYPE=3215 > > RDEVICE ADDRESS=008,DEVTYPE=3215 > > RDEVICE ADDRESS=009,DEVTYPE=3215 > > RDEVICE ADDRESS=00A,DEVTYPE=3215 > > RDEVICE ADDRESS=(01F),DEVTYPE=3215 > > > >RDEVICE ADDRESS=(010,7),DEVTYPE=3277 > > > >RCTLUNIT ADDRESS=0C0,CUTYPE=3272,FEATURE=32-DEVICE > > RDEVICE ADDRESS=(0C0,32),DEVTYPE=3277 > > > >RCTLUNIT ADDRESS=1C0,CUTYPE=3272,FEATURE=16-DEVICE > > RDEVICE ADDRESS=(1C0,7),DEVTYPE=3277 > > RDEVICE ADDRESS=(1C7),DEVTYPE=3284 > > RDEVICE ADDRESS=(1C8,7),DEVTYPE=3277 > > RDEVICE ADDRESS=(1CF),DEVTYPE=3284 > > > >RCTLUNIT ADDRESS=2C0,CUTYPE=3272,FEATURE=16-DEVICE > > RDEVICE ADDRESS=(2C0,7),DEVTYPE=3278,MODEL=4 > > RDEVICE ADDRESS=(2C7),DEVTYPE=3284 > > RDEVICE ADDRESS=(2C8,7),DEVTYPE=3277 > > RDEVICE ADDRESS=(2CF),DEVTYPE=3284 > > > >RCTLUNIT ADDRESS=3C0,CUTYPE=3272,FEATURE=16-DEVICE > > RDEVICE ADDRESS=(3C0,7),DEVTYPE=3277 > > RDEVICE ADDRESS=(3C7),DEVTYPE=3284 > > RDEVICE ADDRESS=(3C8,7),DEVTYPE=3277 > > RDEVICE ADDRESS=(3CF),DEVTYPE=3284 > > > >The configuration file as currently shipped with the SixPack > does not > >define this many terminals. If I expand it to match the above, it > >looks like this: > > > >0009 3215-C NOPROMPT > >000A 1052 NOPROMPT > > > >00C0.32 3270 > >01C0.7 3270 > >01C8.7 3270 > >02C0.7 3270 > >02C8.7 3270 > >03C0.7 3270 > >03C8.7 3270 > > > >With the above configuration, I can connect many 3278-2 (24 line) > >terminals. They come in at 0C0 and go up from there. > > > >Also, I can connect a 3278-4 (40 line) terminal at 2C0. But > I cannot > >connect a second 3278-4. > > > >Does anyone know what is amiss here? > > > >Thanks, Bob > > > > > > > >--- In [email protected], Mike Voss <mike@...> wrote: > >> > >> Now for an *actual* noob question: > >> > >> terminals 0C0-0C2 are defined in hercules, but I can only open a > >> session and > >connect to CP through 0C0. 0C1 just sits at the Hercules banner. > >> > >> I've heard the term directory, how does that interact with or > >> substitute for > >VM's IOGEN? Where do I find either of these entities? -Or does this > >have nothing at all to do with that? > >> > >> A two-or-three-sentence primer on VM I/O targeted to an MVSer will > >> probably > >kickstart me suitably. I know MVS sysgens but this seems to > come at me > >a little bit sideways. I'll wager that at the end of the day > it's more > >familiar than I think. > >> I always secretly wanted to be a DOS/VM guy but none of my > employers > >> ever > >wanted to, er, "re-size" their existing MVS installation. At my very > >first shop we were bringing the systems in-house from a > service bureau, > >and all the VM manuals had arrived, and I was burning through those > >when they changed their minds and I had to learn instead to support > >MVS/SP. Can't complain, it just would have been fun... -and > >retrospectively, the right call for a company of that size. > IBM sales > >was just too darn good. > >> > > > > > > > > > ------------------------------------ > > Yahoo! Groups Links > > >