Re: psscale annotation precision

Hi WSC,

Appears to be possible in GMT5 (see attached file).

But I need do remove two starting ";" in seis_eng.cpt to avoid this message:
psscale: Error: Color palette table seis_eng.cpt has an overlap between
slices 9 and 10

And need to run psscale two times to avoid this message:
psscale: Syntax error -L option: Cannot be used with -B option.

I used the following commands:
gmt psscale -V -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt
-B0:max=69.017075:/:gal: -S -N -K > scale1.ps
gmt psscale -V -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -L -S -N
--FORMAT_FLOAT_MAP=%g -O >> scale1.ps

Regards,

Marcelo



On Wed, Nov 20, 2013 at 7:29 AM, Peter Schmidt <[email protected]>wrote:

>  To my knowledge this cannot be solved (in GMT4 not sure about GMT5). A
> workaround (albeit tedious) is to plot as many colorscales as you want
> annotations and use the -B option to plot a single annotation at the time,
> e.g.
>
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4000.01-40000 -L -S -K
> --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4000.07-40000 -L -S -K
> -O --D_FORMAT=%.2f> scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4000.38-40000 -L -S -K
> -O --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4001.97-40000 -L -S -K
> -O --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4010.25-40000 -L -S -K
> -O --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4053.28-40000 -L -S -K
> -O --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B4276.93-40000 -L -S -K
> -O --D_FORMAT=%.2f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B5439-40000 -L -S -K -O
> --D_FORMAT=%.0f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B11482-40000 -L -S -K -O
> --D_FORMAT=%.0f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B38800 -L -S -K -O
> --D_FORMAT=%.0f > scale.ps
> psscale -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt -B40000:max=69.017075:/:gal:
> -L -S -O > scale.ps
>
> should do the trick
>
> \p
>
>
> On 11/20/2013 10:07 AM, WSC wrote:
>
> Hi,
> I used the following following command to plot a scale that i attached.
>
>  psscale -V -D3.3i/1.5i/6.6i/0.25ih -Cseis_eng.cpt
> -B:max=69.017075:/:gal:  -L -S -N >scale.ps
>
>  and what I want is the annotation can be marked like the color_cpt file
> attached ,which is:the float number can be marked with 2 or 3 numbers
> after the dot, and the Integer numer are just marked what it is !
> Simply, 0.014 is annotated "0.014",But "3899" is "3899", Not "3899.000"!
>
>  Please Help!
> Thanks!
>
>  WSC
>
>
>
>
>
> --
> ********************************************************************************
> Peter Schmidt                                      Tel: +46-18-4717104
> Swedish National Seismological Network (SNSN)   Mobile: +46-73-3190975
> Dept. of Earth Sciences:geophysics              e-mail: [email protected]
> Uppsala University
> Villavagen 16
> SE-75236 Uppsala
> ********************************************************************************
>
>  To unsubscribe, send the message "signoff gmt-help" to
> [email protected]

To unsubscribe, send the message "signoff gmt-help" to [email protected]