Communications Error

Hi

I have xda || PDA   and I was tring to sync my PDA  with linux so I
follow the page :

http://synce.sourceforge.net/synce/howto.php

and was able to load the ipaq module and to detect my pda when I plug it in :

hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:1d.1: port 2 portsc 008a
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
usb 3-2: USB disconnect, address 47
usb 3-2: usb_disable_device nuking all URBs
usb 3-2: unregistering interface 3-2:1.0
PocketPC PDA ttyUSB1: PocketPC PDA converter now disconnected from ttyUSB1
ipaq 3-2:1.0: device disconnected
usb 3-2:1.0: hotplug
usb 3-2: unregistering device
usb 3-2: hotplug
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100


now when I type

synce-serial-config usb/tts/0

USER= dccm

synce-serial-start


I get the following message from ActiveSync in the PDA :

+-------------------------------------------------------+
 |          Communications Error              |
+-------------------------------------------------------+
 |  Cannot start communications with     |
 |   the desktop computer                      |
 |                                                         |
 |  Reconnect your device if the problem  |
 | persists,see Microsoft ActiveSync Help|
------------------------------------------------------------


and in the log message I got :

Dec 26 09:13:50 lnx1w034 uhci_hcd 0000:00:1d.1: port 2 portsc 0093
Dec 26 09:13:50 lnx1w034 hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
Dec 26 09:13:50 lnx1w034 hub 3-0:1.0: debounce: port 2: total 100ms
stable 100ms status 0x101
Dec 26 09:13:50 lnx1w034 usb 3-2: new full speed USB device using address 106
Dec 26 09:13:50 lnx1w034 usb 3-2: new device strings: Mfr=0,
Product=0, SerialNumber=0
Dec 26 09:13:50 lnx1w034 usb 3-2: hotplug
Dec 26 09:13:50 lnx1w034 usb 3-2: adding 3-2:1.0 (config #1, interface 0)
Dec 26 09:13:50 lnx1w034 usb 3-2:1.0: hotplug
Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: usb_probe_interface
Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: usb_probe_interface - got id
Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: PocketPC PDA converter detected
Dec 26 09:13:50 lnx1w034 usb 3-2: PocketPC PDA converter now attached to ttyUSB1


and when I run pstatus I get :
pstatus: Unable to initialize RAPI: An unspecified failure has occurred


Any Help please


-- 
Best Regards,
--------------------
-*- If Linux doesn't have the solution, you have the wrong problem -*-


-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/