Re: Communications Error

Sorry

After rebooting the system everything went fine,  I feel I am in windows :)


On Sun, 26 Dec 2004 09:17:21 +0300, regatta <[email protected]> wrote:
> Hi
> 
> I have xda || PDA   and I was tring to sync my PDA  with linux so I
> follow the page :
> 
> http://synce.sourceforge.net/synce/howto.php
> 
> and was able to load the ipaq module and to detect my pda when I plug it in :
> 
> hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
> uhci_hcd 0000:00:1d.1: port 2 portsc 008a
> hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
> usb 3-2: USB disconnect, address 47
> usb 3-2: usb_disable_device nuking all URBs
> usb 3-2: unregistering interface 3-2:1.0
> PocketPC PDA ttyUSB1: PocketPC PDA converter now disconnected from ttyUSB1
> ipaq 3-2:1.0: device disconnected
> usb 3-2:1.0: hotplug
> usb 3-2: unregistering device
> usb 3-2: hotplug
> hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
> 
> now when I type
> 
> synce-serial-config usb/tts/0
> 
> USER= dccm
> 
> synce-serial-start
> 
> I get the following message from ActiveSync in the PDA :
> 
> +-------------------------------------------------------+
>  |          Communications Error              |
> +-------------------------------------------------------+
>  |  Cannot start communications with     |
>  |   the desktop computer                      |
>  |                                                         |
>  |  Reconnect your device if the problem  |
>  | persists,see Microsoft ActiveSync Help|
> ------------------------------------------------------------
> 
> and in the log message I got :
> 
> Dec 26 09:13:50 lnx1w034 uhci_hcd 0000:00:1d.1: port 2 portsc 0093
> Dec 26 09:13:50 lnx1w034 hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
> Dec 26 09:13:50 lnx1w034 hub 3-0:1.0: debounce: port 2: total 100ms
> stable 100ms status 0x101
> Dec 26 09:13:50 lnx1w034 usb 3-2: new full speed USB device using address 106
> Dec 26 09:13:50 lnx1w034 usb 3-2: new device strings: Mfr=0,
> Product=0, SerialNumber=0
> Dec 26 09:13:50 lnx1w034 usb 3-2: hotplug
> Dec 26 09:13:50 lnx1w034 usb 3-2: adding 3-2:1.0 (config #1, interface 0)
> Dec 26 09:13:50 lnx1w034 usb 3-2:1.0: hotplug
> Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: usb_probe_interface
> Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: usb_probe_interface - got id
> Dec 26 09:13:50 lnx1w034 ipaq 3-2:1.0: PocketPC PDA converter detected
> Dec 26 09:13:50 lnx1w034 usb 3-2: PocketPC PDA converter now attached to ttyUSB1
> 
> and when I run pstatus I get :
> pstatus: Unable to initialize RAPI: An unspecified failure has occurred
> 
> Any Help please
> 
> 
> --
> Best Regards,
> --------------------
> -*- If Linux doesn't have the solution, you have the wrong problem -*-
> 


-- 
Best Regards,
--------------------
-*- If Linux doesn't have the solution, you have the wrong problem -*-


-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/